Black Box ServSwitch manual Enter the starting cpu number →

Page 87

MATRIX SERVSWITCH™

7.2.1OPTION 1. CHANGE STARTING COMPUTER

This option can only be changed if your computer or terminal is attached to the serial port of port board 1 (the bottom board that includes CPU ports 1 through 4—see Figure 2-3 in Section 2.4 for board numbering).

The serial options menu displays the currently configured starting-CPU number in option 1. To change option 1 (starting CPU), press 1; you’ll see this prompt:

Enter the starting cpu number

Type the new number and press [Enter]. The serial options menu will be displayed again. Use option 7 to permanently save this change to the flash memory of the port board (see Section 7.2.6), then cycle power to the Switch to distribute the change to all of the other port boards in the Switch.

7.2.2OPTION 2. CHANGE SERIAL-PORT BAUD RATE (DATA RATE)

Change the setting of this option to change the baud rate (data rate) of the Matrix ServSwitch port board you are communicating with. Before you select it, this option will show the current speed of the port board’s serial port as either “9600” or “57,600” (bps). You can change this rate just by pressing 2 to select this option, so be careful about doing that. After you do select this option, these messages will appear (still at the old data rate):

Baud rate changed to 9600 [or 57,600]

Set baud rate of your terminal to 9600 [or 57,600] and press

return

If you’re using a terminal or a better communication program, you will be able to change your terminal’s or communication program’s data rate on the fly to match that of the Switch’s port board. (Refer to the comm program’s manual or online help for instructions on doing this.) If you’re using Windows Hyperterminal, however, you’ll need to temporarily disconnect from the Switch, change the data rate, then reconnect:

1.Select “Disconnect” from the “Call” pulldown menu.

2.Select “Properties” from the “File” pulldown menu.

3.Select “Configure” and change the data rate in the field labeled “Baud rate.”

4.Press “OK” to save your new PC data rate.

5.Select “Connect” from the “Call” pulldown menu.

Once you’ve changed the data rate on your end, press [Enter]. The serial options menu will be displayed again, at the new port-board data rate. Use option 7 to permanently save this change to the port board’s flash memory (see

Section 7.2.6).

86

Image 87
Contents SW741A-R3 SW742A-R3 SW743A-R3 SW761A-R3 SW762A-R3 SW763A-R3 SW741A-R3 SW742A-R3 SW743A-R3 SW761A-R3 SW762A-R3 SW763A-R3 Welcome to the ServSwitchTM FamilyMatrix Servswitch European Union Declaration of Conformity Matrix Servswitch NOM Statement Contents Table of Contents Matrix Servswitch Appendix Hardware SpecificationsMaximum SpecificationsMaximum Altitude Temperature TolerancePower WeightComplete Package IntroductionSecurity FeaturesUpgradability CompatibilityOn-Screen Display Technology FlexibilityFront Panel Front panel of a 2 x 16 Matrix ServSwitch SW743A-R3Right/Green CPU Power Panel Label DescriptionLeft/Red Select Rear Panel Designation Connector DescriptionSee Section KVM 1RS-232 N Equipment Requirements Cable RequirementsQuick Setup Guide Installation and PreconfigurationCpus Installation and Preconfiguration Matrix Servswitch Keyboard mapping by the Matrix ServSwitch Monitor Video quality vs. distance for original Serv cables Video quality vs. distance for coaxial cables Important Note Installation ProcedureRackmounting Optional Connecting Cpus Connecting Other Matrix Servswitches Optional Powering UP the Switches Switching and Accessing the Display from the Keyboard Expansion Module and its input and output ports Daisychaining Matrix ServSwitchesBus topology Ring topology Power-Up Procedure Diagnostic screen Diagnostic Messages Description Ports see SectionSection Configuration Checksum Error Kernel ErrorMain Program Error Sram ErrorKernel is bad, load new kernel through serial port Error reason Hit space bar within 5 seconds to get serial options menu Initial Configuration Initially Configuring Multiple Daisychained Units CPU Ports KVM Full ConfigurationUsing the Menu Saving configuration changes Configure password Configuring the SystemPC keyboard rate PC keyboard delayStarting computer number Maximum computerScreen saver time Sun keyboard language multiplatform models onlyMenu color scheme Screen saverBackground color, text color PositionFadeout Configuring Computers Computer NumberComputer Name Keyboard Bus Configuring User StationsProfile ResolutionKVM Name StartConfiguring User Definitions PasswordUser name Configure Profile Configuring User ProfilesAccess NameConnect Share ScanLogout Configuring Groups Group n where n = 1 throughComputer Group Name Slot PowerStatus ComputersVer UserStatus Logging On-Screen Functions, Same-Port Users, and Connection ModesStatus Control Room Connection-Status MessagesReasons for connection failure Disconnect-status message Reasons for disconnection User Stations Attached to Same-Numbered Ports A 6-user-by-8-computer Matrix ServSwitch/ServShare system Connection Modes Connection dynamics between users Command Summary Keyboard CommandsKeyboard Commands Display CPU List Ctrl Esc Display Configuration Menu Ctrl F12Select Computer Ctrl xxxx Enter Switch to the Next Port in Sequence Ctrl +Switch to the Previous Port in Sequence Ctrl Switch to the Prior Port Ctrl ← or Ctrl BackspaceDisconnect Ctrl Q Reset Ctrl RDisplay User-Station Status Ctrl D Log Out Ctrl LSend Null Byte to PS/2 Type Mouse Ctrl N Reset/Enable Mouse in Windows NT and Unix Ctrl OStart Scan Ctrl S Identify Firmware Revision CtrlEnd Scan Ctrl Pass This Command Through Ctrl X or Ctrl TabBasic Setup Establishing a Serial Connection Using the Serial PortsSerial Options Menu Using the Serial PortsEnter the starting cpu number → Waiting for file Receive failed Try again Y/N Sending flash program code to system Flash programming Option 8. Exit and Restart Unit Common Problems TroubleshootingCharacters that you type come up wrong or missing You can’t switch ports from the keyboardAn IBM compatible computer’s mouse driver doesn’t load You can’t seem to scan or switch to certain ports at allYou can’t access all the functions of your mouse Your PS/2 mouse gets out of syncYour mouse doesn’t move the pointer/cursor Your video is not synchronized or is the wrong color Your monitor display is fuzzyMatrix ServSwitch doesn’t work with your docking station Matrix ServSwitch doesn’t work with your IBM ThinkPadYour on-screen display is not synchronized Shipping and Packaging Calling Black BoxDerived from hardware Appendix a Nvram Factory Defaults100 Appendix B Cable Product Codes 102 103 Appendix C Pinout of Serial Ports Key Pressed on Scan Code LK461 Keyboard Appendix D The LK461 KeyboardSetting the RING/BUS Jumper Jumper JP1 on Expansion Modules Appendix E Installing Modules Matrix ServSwitchSwapping In an Expansion Module Swapping In a Terminator Module Not Recommended Appendix F Rackmounting Matrix ServSwitch Figure F-1. Rackmount assembly Page Page
Related manuals
Manual 4 pages 8.8 Kb Manual 20 pages 59.79 Kb

ServSwitch specifications

The Black Box SRX ServSwitch is an innovative KVM (Keyboard, Video, Mouse) switch that offers robust solutions for managing multiple computers from a single workstation. This device stands out in environments ranging from data centers to broadcasting studios, where efficient control over multiple systems is crucial.

One of the key features of the SRX ServSwitch is its high-resolution video support. It can handle video resolutions up to 4K at 60Hz, ensuring that users can enjoy sharp and clear visuals without lag. This level of performance is essential for professionals who rely on precise graphics for tasks such as video editing and design work.

The SRX ServSwitch employs advanced USB technology, allowing for seamless connectivity with various peripherals. It supports USB 2.0 devices, which means users can connect printers, external drives, and other devices without worrying about compatibility issues. Additionally, the switch allows for USB device sharing, enabling multiple computers to access the same peripherals efficiently.

Security is a significant concern in today’s IT environments, and the Black Box SRX ServSwitch addresses this through its advanced security features. It includes support for secure booting and end-to-end encryption, ensuring that data remains protected when switching between systems. This makes it suitable for environments that handle sensitive information, such as financial institutions or healthcare facilities.

The design of the SRX ServSwitch is another standout characteristic. With its easy-to-use interface, users can quickly switch between connected systems using hotkey commands or the push-button interface. This usability improves productivity since users can manage multiple systems without the hassle of different keyboards and mice.

Furthermore, the SRX ServSwitch is built to be scalable, allowing for the addition of more channels as needed. This flexibility means that organizations can adapt their KVM switch setup as their operational needs grow. It supports both local and remote management, offering organizations the ability to control systems from various locations seamlessly.

The build quality of the Black Box SRX ServSwitch is robust, designed to handle the rigors of continuous use in demanding environments. It is compatible with various operating systems, ensuring that users can integrate it into their existing setups without significant reconfiguration.

In summary, the Black Box SRX ServSwitch offers a comprehensive solution for KVM management, characterized by high-resolution video support, USB compatibility, security features, easy usability, scalability, and durability. It is a valuable investment for organizations seeking an efficient way to manage multiple systems centrally.