Fujitsu MB88121 SERIES, MB91460 SERIES manual Starter kit status after power on

Page 13

SK-91F467-FLEXRAY V1.1

Installation

For the power supply of the SK-91F467-FLEXRAY a DC input voltage of 9V – 12V is recommended. The positive voltage (+) must be connected to the shield, and ground (GND) must be connected to the centre of the connector X5!

After power-on of the SK-91F467-FLEXRAY, the four red power-on LEDs D24 (5V), D30 (3.3V), D34 (2.5V) and D40 (1.8V) should be light. The reset LED D18 should be off.

Additionally the LED D2 and D4 should be on. The starter kit is delivered with programmed Softune Workbench Monitor Debugger in internal Flash of MB91F467D series. The monitor debugger is checking also the external SRAM access at CS1. In case of successful access to external SRAM the LED D2 and D4 are ON. In case of failed access LED D1 and D4 are set to ON.

Figure 2-5: Starter kit status after power on

© Fujitsu Microelectronics Europe GmbH

- 13 -

FMEMCU-UG-910017-11

Image 13

Contents MB88121 Series MB91460 Series Revision History Date IssueNo Liability for Consequential Damages Warranty and DisclaimerContents Connectors Trouble Shooting SILK-PLOT of the Board Abstract IntroductionFeatures General Description External Bus interface Connectors MCU Operating ModeOn Board Memory MCU ClocksPower Supply MCU PinsUser Buttons User LEDs and optional LCDAC plug adapter InstallationStarter kit status after power on Jumper Description / Function Type Default Jumper SettingsUART4 RTS CTS Jumper settingsJumper Location Default Jumper SettingsSoftune Workbench start menu location Software Installation Installation of Softune WorkbenchSoftune Workbench V6 IDE DIP switch Setting Logical value Jumpers and SwitchesMCU Operating Mode MCU Operating-Mode S5FlexRay CC Operating-Mode S2 FlexRay CC Operating ModeFlexRay CC SPI Settings FlexRay CC SPI Settings S1Power Switch Switch Setting DescriptionJumper Setting Description Power supply configurationsRegulator Test point Voltage Voltage Test PointsMCU Analogue Power Supply Voltage MCU Power Supply VoltageMCU Power Supply SK-91F467-FLEXRAY MCU ADC Supply FlexRay CC Power Supply Voltage at SK-91F467-FLEXRAYFlexRay CC Supply JP7 MCU-FlexRay CC Connection at SK-91F467-FLEXRAY10 MCU-FlexRay CC Connection Channel aChannel B 11 FlexRay CH-A Configuration12 FlexRay CH-B Configuration 13 FT1080 Control Settings 3 FT1080 Control Settings S614 FT1080 Connection to MCU LIN / RS-232 Uart CAN0 CAN215 CAN-MCU connection Uart 16 UART2 SettingsUart 4 Flash programming 17 UART4 Settings18 UART5 Settings DIP switch Setting Description User DIP Switch 8 Bit S4User Push Buttons INT0, INT1, INT2 and ICU0/TIN0 22 Reset Connections Reset Generation23 Supply Monitor Settings By default the Uart reset is disabled 24 Reset Uart SelectionPower Connector ConnectorsUart / LIN Connector X1, X4 Pin Number Pin Signal DescriptionFlexRay Connector X2 Can Connector X9, X10Can Connector Signals FlexRay Connector SignalsFlexRay Physical Layer Modules FlexRay Physical Layer Module Connector X3USER-LEDs and optional LC-Display D1-D16, J6 LED/LCD SignalsMCU Pin Connectors J1-J4 In-Circuit-Programming ConnectorIn-Circuit Programming Connector Connector MCU PinsVG96 X13 Signals External Bus Connectors X13, X14 4.9.1 VG96ABC DIN 41612VG48 X14 Signals Distance between VG-Connectors2 VG48ABC DIN 41612 Softune Workbench main window Introduction to Softune WorkbenchSK-91F467-FLEXRAY Getting Started Create a New Project Project Start-upEnter the folder myapplication Edit myapplication.prjOpen Softune Workbench workspace *.wsp Select Active Configuration Mondebug Use Active Configuration MondebuginternalSoftune Workbench Linker Mapping Start Softune Monitor Debugger via the Debug Command Use Active configuration StandaloneGeneral Description Softune Workbench Monitor DebuggerUser LEDs U1, MCU MB91F467DA DIP switch S5, default all OFFSWB debugging window Basic Debugger Features Use the button INT0 on the SK-91F467-xxx for Abort function Advanced Monitor Debugger FeaturesExample SK-91F467-FLEXRAY Getting Started Memory Map of Softune Workbench Monitor debugger Memory Configuration for User ApplicationsMemory Type Used for Areas Sections 0x0080.0000 0x009F.FFFF Checklist for project configurationProgramming internal Flash of MB91F467DA series Flash ProgrammingFMEMCU-UG-910017-11 Fujitsu Microelectronics Europe GmbH FME Flash Programmer output message window Trouble shooting Trouble shootingTop Side Silk-Plot of the BoardBoard Layout Bottom Side Bottom SideSK-91F467-FLEXRAY PCB HistoryHistory PCB Related Products AppendixInformation on the WWW Tables Trouble shooting History PCB Figures Usart Abbreviations