Fujitsu MB88121 SERIES Project Start-up, Create a New Project, Enter the folder myapplication

Page 47

SK-91F467-FLEXRAY V1.1

Getting Started

5.2Project Start-up

In order to allow a quick and smooth project start-up Fujitsu Microelectronics Europe supplies a template project as a reference. The easiest way to start a new project is to make a copy of the template project and use this copy as a start-up. The template includes the latest start91460.asm file, MCU header file, IRQ table, basic linker and C-Compiler settings.

Note:

In any case the settings done in the template must be checked and have to be adjusted to the specific needs and settings of the final application. The template is providing an example for building up a new project.

THIS SAMPLE CODE IS PROVIDED AS IS AND IS SUBJECT TO ALTERATIONS. FUJITSU MICROELECTRONICS ACCEPTS NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS

OR/ELIGIBILITY FOR ANY PURPOSES.

(C) Fujitsu Microelectronics Europe GmbH

5.2.1Create a New Project:

1.In order to start a new user-project use the “91460_template_91467d” project

2.Copy the folder 91460_template_91467d and rename the folder to e.g. my_application

3.Enter the folder “my_application”

Rename “91460_template_91467d.prj” into “my_application.prj” Rename “91460_template_91467d” into “my_application.wsp”

4.Edit “my_application.prj”

Rename “91460_template_91467d” -> “my_application”

5.Edit “my_application.wsp”

Rename “91460_template_91467d” -> “my_application”

© Fujitsu Microelectronics Europe GmbH

- 47 -

FMEMCU-UG-910017-11

Image 47
Contents MB88121 Series MB91460 Series Revision History Date IssueNo Liability for Consequential Damages Warranty and DisclaimerContents Connectors Trouble Shooting SILK-PLOT of the Board Abstract IntroductionFeatures General Description MCU Clocks MCU Operating ModeExternal Bus interface Connectors On Board MemoryUser LEDs and optional LCD MCU PinsPower Supply User ButtonsAC plug adapter InstallationStarter kit status after power on Jumper Description / Function Type Default Jumper SettingsUART4 RTS CTS Jumper settingsJumper Location Default Jumper SettingsSoftune Workbench start menu location Software Installation Installation of Softune WorkbenchSoftune Workbench V6 IDE MCU Operating-Mode S5 Jumpers and SwitchesDIP switch Setting Logical value MCU Operating ModeFlexRay CC Operating-Mode S2 FlexRay CC Operating ModeFlexRay CC SPI Settings FlexRay CC SPI Settings S1Power supply configurations Switch Setting DescriptionPower Switch Jumper Setting DescriptionRegulator Test point Voltage Voltage Test PointsMCU Power Supply SK-91F467-FLEXRAY MCU Power Supply VoltageMCU Analogue Power Supply Voltage FlexRay CC Supply FlexRay CC Power Supply Voltage at SK-91F467-FLEXRAYMCU ADC Supply JP7 MCU-FlexRay CC Connection at SK-91F467-FLEXRAY10 MCU-FlexRay CC Connection Channel aChannel B 11 FlexRay CH-A Configuration12 FlexRay CH-B Configuration 14 FT1080 Connection to MCU 3 FT1080 Control Settings S613 FT1080 Control Settings 15 CAN-MCU connection CAN0 CAN2LIN / RS-232 Uart Uart 16 UART2 SettingsUart 4 Flash programming 17 UART4 Settings18 UART5 Settings User Push Buttons INT0, INT1, INT2 and ICU0/TIN0 User DIP Switch 8 Bit S4DIP switch Setting Description 23 Supply Monitor Settings Reset Generation22 Reset Connections By default the Uart reset is disabled 24 Reset Uart SelectionPin Number Pin Signal Description ConnectorsPower Connector Uart / LIN Connector X1, X4FlexRay Connector Signals Can Connector X9, X10FlexRay Connector X2 Can Connector SignalsFlexRay Physical Layer Modules FlexRay Physical Layer Module Connector X3USER-LEDs and optional LC-Display D1-D16, J6 LED/LCD SignalsConnector MCU Pins In-Circuit-Programming ConnectorMCU Pin Connectors J1-J4 In-Circuit Programming ConnectorVG96 X13 Signals External Bus Connectors X13, X14 4.9.1 VG96ABC DIN 416122 VG48ABC DIN 41612 Distance between VG-ConnectorsVG48 X14 Signals Softune Workbench main window Introduction to Softune WorkbenchSK-91F467-FLEXRAY Getting Started Edit myapplication.prj Project Start-upCreate a New Project Enter the folder myapplicationOpen Softune Workbench workspace *.wsp Select Active Configuration Mondebug Use Active Configuration MondebuginternalSoftune Workbench Linker Mapping Start Softune Monitor Debugger via the Debug Command Use Active configuration StandaloneGeneral Description Softune Workbench Monitor DebuggerUser LEDs U1, MCU MB91F467DA DIP switch S5, default all OFFSWB debugging window Basic Debugger Features Use the button INT0 on the SK-91F467-xxx for Abort function Advanced Monitor Debugger FeaturesExample SK-91F467-FLEXRAY Getting Started Memory Type Used for Areas Sections Memory Configuration for User ApplicationsMemory Map of Softune Workbench Monitor debugger 0x0080.0000 0x009F.FFFF Checklist for project configurationProgramming internal Flash of MB91F467DA series Flash ProgrammingFMEMCU-UG-910017-11 Fujitsu Microelectronics Europe GmbH FME Flash Programmer output message window Trouble shooting Trouble shootingTop Side Silk-Plot of the BoardBoard Layout Bottom Side Bottom SideHistory PCB PCB HistorySK-91F467-FLEXRAY Related Products AppendixInformation on the WWW Tables Trouble shooting History PCB Figures Usart Abbreviations