TRENDnet BRF114 manual Data - Special Applications Screen, Using a Special Application

Page 48

Figure 28: Special Applications Screen

TW100-BRF114 User’s Guide

Figure 28: Special Applications Screen

Data - Special Applications Screen

Checkbox

Name

Incoming Ports

Outgoing Ports

Use this to Enable or Disable this Special Application as required.

Enter a descriptive name to identify this Special Application.

•Type - Select the protocol (TCP or UDP) used when you receive data from the special application or service. (Note: Some applications use different protocols for outgoing and incoming data).

•Start - Enter the beginning of the range of port numbers used by the application server, for data you receive. If the application uses a single port number, enter it in both the "Start" and "Finish" fields.

•Finish - Enter the end of the range of port numbers used by the applica- tion server, for data you receive.

•Type - Select the protocol (TCP or UDP) used when you send data to the remote system or service.

•Start - Enter the beginning of the range of port numbers used by the application server, for data you send to it. If the application uses a sin- gle port number, enter it in both the "Start" and "Finish" fields.

•Finish - Enter the end of the range of port numbers used by the applica- tion server, for data you send to it. If the application uses a single port number, enter it in both the "Start" and "Finish" fields.

Using a Special Application

•Configure the Special Applications screen as required.

•On your PC, use the application normally. Remember that only one (1) PC can use each Special application at any time. Also, when 1 PC is finished using a particular Special Ap- plication, there may need to be a "Time-out" before another PC can use the same Special Application. The "Time-out" period may be up to 3 minutes.

44

Image 48

Contents Page Page Table of Contents TW100-BRF114 FeaturesPackage Contents CHAPTER 2 INSTALLATIONAPPENDIX A TROUBLESHOOTING General ProblemsInternet Access APPENDIX B SPECIFICATIONSTW100-BRF114 Features Internet Access FeaturesIntroduction ChapterLAN Features Configuration & ManagementSecurity Features Advanced Internet FunctionsPackage Contents Physical Details Front-mounted LEDsPower Green Status Red On - Corresponding LAN hub port is using 100BaseTRear Panel Reset ButtonTo Clear All Data and restore the factory default values Power portInstallation ProcedureRequirements This Chapter covers the physical installation of the TW100-BRF1144. Power Up 3. Connect WAN Cable5. Check the LEDs Setup OverviewThis Chapter provides Setup details of the TW100-BRF114 To Do thisConfiguration Program PreparationUsing your Web Browser If you cant connectSetup Wizard Common Connection TypesType DetailsOther Modems e.g. Broadband Wireless Big Pond Cable AustraliaSingTel RAS Home Screen Navigation & Data InputFigure 5 Home Screen LAN Screen CancelFigure 6 LAN Screen TCP/IPDHCP Using the TW100-BRF114 s DHCP ServerUsing another DHCP Server To Configure your PCs to use DHCPPassword Screen Figure 7 Password ScreenFigure 8 Password Dialog PC Configuration TCP/IP Settings - OverviewWindows Clients Checking TCP/IP Settings - Windows 9x/ME Using DHCPUsing Specify an IP Address Figure 9 Network ConfigurationPC Configuration Figure 11 Gateway Tab Win 95/98/MEFigure 12 DNS Tab Win 95/98/ME Checking TCP/IP Settings - Windows NT4.0 Figure 13 Windows NT4.0 - TCP/IPObtain an IP address from a DHCP Server Specify an IP AddressFigure 14 Windows NT4.0 - IP Address Figure 15 - Windows NT4.0 - Add Gateway Figure 16 Windows NT4.0 - DNS Checking TCP/IP Settings - Windows Figure 17 Network Configuration Win1. Select Control Panel - Network and Dial-up Connection Figure 18 TCP/IP Properties Win Checking TCP/IP Settings - Windows XP Figure 19 Network Configuration Windows XP1. Select Control Panel - Network Connection Figure 20 TCP/IP Properties Windows XP Checking TCP/IP Settings - Windows Vista PC Configuration Internet Access 1. Select Start Menu - Settings - Control Panel - Internet Options2. Select Set up or change your Internet Connection 3. Select Set up a Connection or NetworkClick Save, then OK. Configuration is now complete Macintosh Clients Linux ClientsOther Unix Systems Ensure you are logged in as root before attempting any changesOperation and Status OperationStatus Screen This indicates the current connection method, as set in the SetupConnection Status - PPPoE Broadband ModemInternet Connection Internet IP AddressFigure 22 PPPoE Status Screen ConnectionPhysical Address PPPoE Link StatusConnection Log Messages MessageDescription Connection Status - PPTP Figure 23 PPTP Status ScreenPPTP Status Connection Status - Telstra Big Pond Figure 24 Telstra Big Pond Status ScreenConnection Status Connection Details - SingTel RAS Default GatewayFigure 25 Connection Details - SingTel RAS RAS PlanConnection Details - Fixed/Dynamic IP Address Release/RenewButton will display EITHERDNS IP Address Internet Features Advanced Internet ScreenFigure 27 Internet Screen Communication Applications Special ApplicationsCommunication Applications Select an ApplicationUsing a Special Application Data - Special Applications ScreenFigure 28 Special Applications Screen Checkbox Name Incoming Ports Outgoing PortsPage URL Filter Screen Figure 29 URL Filter ScreenFilter Strings Current EntriesDynamic DNS Domain Name Server Dynamic DNS ScreenThe Service works as follows DDNS ServicePassword DDNS DataUser Name Domain NameMAC Address MAC Address ScreenDefault Figure 31 MAC address ScreenVirtual Servers IP Address seen by Internet UsersFigure 32 Virtual Servers Virtual Servers Screen EnableFigure 33 Virtual Servers Screen ServersDefining your own Virtual Servers DefaultsDisable All UpdateConnecting to the Virtual Servers Other Features and Settings UpgradeRemote ManagementAccess Control Access Control ScreenOverview If required, you can also define your own ServicesInternet Access ServicesEdit Service List GroupGroup Members Screen PCs not assigned to any group will be in the Default groupPCs deleted from any other Group will be added to the Default group View LogDefault Schedule Screen Figure 36 Default Schedule ScreenEnter the start using a 24 hr clock Enter the finish time using a 24 hr clockServices Screen Figure 37 Access Control - ServicesAvailable Services Available ServicesAccess Control Log Date/TimeSource IP address MAC addressRemote Management Enable RemoteFigure 38 Remote Management Screen Remote ManagementPC Database PC Database ScreenFigure 39 PC Database Known PCsAdministration Generate ReportAdvanced PC Database Admin Figure 40 PC Database AdminPC Properties DCHP Client - Reserved IP Address - Select this if the PC is setUpdate Selected Add as NewEntry Standard ScreenUpgrade Firmware To perform the Firmware UpgradeFigure 41 Upgrade Firmware Screen Options Backup DNSFigure 42 Options Screen MTU sizeSecurity Enable DoSFigure 43 Security Screen FirewallAllow IPsec Allow PPTPAllow L2TP Logs Enable LogsAdjust for Daylight Figure 44 Logs ScreenE-Mail Logs Send E-mail alertE-mail Logs SendRouting Routing ScreenUsing this Screen Open Routing and Remote AccessEnable RIP Figure 45 Routing ScreenStatic Routing Static RoutingConfiguring Other Routers on your LAN Destination IP AddressGateway IP Address MetricStatic Routing - Example For Router As Default RouteFor Router Bs Default Route For the TW100-BRF114 s Routing TableTroubleshooting General ProblemsAppendix A This Appendix covers the most likely problems and their solutionsInternet Access Problem 1 When I enter a URL or IP address I get a time out errorAppendix B Specifications TW100-BRF114Regulatory Approvals Appendix B - Specifications