SATO DR300 manual Print image shifts from its position

Page 31

DR300 Operator Manual

Chapter 5 - Power Supply

 

 

Print image shifts from its position

 

 

Check Point

 

 

Remedy

1.

Are the labels and carbon ribbons

Check if labels and carbon ribbons are

 

properly set?

 

 

fixed firmly and at the correct position by

 

 

 

 

 

lifting head assembly.

2.

Is the platen roller dirty?

 

 

Clean dirt off from platen roller with

 

 

 

 

 

cleaning kit.

3.

Are deformed labels or carbon

Use genuine SATO new labels and carbon

 

ribbons being used?

 

 

ribbons which are in good condition.

4.

Are genuine labels and carbon

Genuine labels and carbon ribbons

 

ribbons

exclusively

for

this

exclusively for this equipment must be

 

equipment being used?

 

 

used.

 

 

 

 

 

Available from SATO.

5.

Is the content of data or signal from

Re-set printer with power off/on.

 

the computer correct?

 

 

If similar message is displayed, check

 

 

 

 

 

content of software and communication

 

 

 

 

 

settings at the computer side.

6.

Is the print position offset setting

Adjust the print position offset.

 

correct?

 

 

 

 

Disconnect printer from mains before cleaning.

29

Image 31
Contents DR300 Copyright 438A Alexandra Road #05-01/02 Alexandra Technopark SingaporeTable of Contents Online Programming …………………………………………… Operation Panel …………………………………………………Serial Interface ………………………………………………… Appendix a Basic Specification ………………………………………………Appendix B Character Code Table ………………………………………… Installation and Operation Instruction Installation and Handling InstructionUnpacking Printer Unit Unpacking Touch Screen Optional Item Accessories Checklist Card Cover Printer cover Power SwitchNames of Parts Sliding GuideOperational Panel Unit Touch Screen / KeypadDisplay Card Cover Unit Back Panel Unit Setting Paper Setting of Label and Carbon RibbonSetting Rolled Paper DR300 Operator Manual DR300 Operator Manual Setting Large Diameter Rolled Label Setting Carbon Ribbon Setting Label and Carbon Ribbon Take caution not to trap your finger when closing the cover Pitch Sensor AdjustmentDR300 Operator Manual DR300 Operator Manual Setting of Label and Carbon Ribbon Stop Position Adjustment DR300 Operator Manual Cutting Paper with Perforation Cut Position Adjustment Cutting of LabelCutter Replacement Tag Guide Set Position Basic Usage of StackerTag Guide Position Stack Position Adjustment, Small Tag Less than 35mmSwitch off Power Switch Power SupplySetting Power Supply Supply PowerCheck Point Remedy Simple TroubleshootingPaper feeds, but no printing Print image shifts from its position Frequency for maintenance Daily MaintenanceCleaning method for printer parts DR300 Operator Manual PC Card Optional PC CardMemory Card Battery Installation / Exchange DR300 Operator Manual Operation Panel Normal ModeOperation Overview Darkness User ModeSelection for Large Label Size Paper Perform Test PrintingSetting Service Mode Default & Service Mode Setting Default ValuePitch a D J Pitch ADJCUT ADJ SET Time Back ADJCode ADJ Setting Non-Standard ProtocodeSTX 7 B Cursor moves to 1 place after set Price ADJ YEN Currency Font SettingPrice ADJ Price ADJ DollarFactory Mode NON ALL, HED, CUT Print Factory ModeNON ALL Head CUT Basic Construction Contents CommandOnline Programming STX Command summary Detail DescriptionInitial Designation Command End Designation CommandDigit Position Data Description Media Parameter TransmissionMaxi Field Parameter TransmissionBOOKLAND*1 OCR-A OCR-B On-line Mode Field Parameter SummaryINT2OF5 Time Field 24H Field data transmission Graphic data transmission Digit Designated Designated Description Position Normal, calendar, true type fieldDigit Designated Item Designated Description Position DD. MM. Yyyy MM. DD. Yyyy Bookland Bar Code FieldHorizontal Position 001~640 Horizontal position dot Graphic Field Transmission DDD DR300 Operator Manual Digit Designated Item Designated Description Position DR300 Operator Manual DR300 Operator Manual Definition Matrix Size Input Data Size Correction level = DR300 Operator Manual DR300 Operator Manual 2D Bar Code Command QR Code Command DR300 Operator Manual Version Error Numeric Alphanumeric Kanji Binary Correction Version Error Numeric Alphanumeric Kanji Binary Correction Version Error Numeric Alphanumeric Kanji Binary Correction Maxi Code Command Serial Interface Serial InterfaceXON/OFF Ready/Busy XON / Xoff Status 3 Protocol Status Summary Table Description Status TransmissionHex DR300 Operator Manual Return Sequence Cancel Demanding Command Reference Flow Chart Basic Specification DR 300 General Specifications Operating Environmental Condition Label & Carbon Ribbon SpecificationDR 300 Software Specifications DIP-Switch Setting DIP-Switch SettingPrinter Main Body Operation Unit OFF Status XON-OFF Setting Content Enable Change parameter by touch screen Character Code Table Appendix BDR300 Operator Manual DR300 Operator Manual DR300 Operator Manual
Related manuals
Manual 18 pages 57.39 Kb