SATO DR300 manual Setting Default Value, Setting Service Mode Default & Service Mode

Page 41

DR300 Operator Manual

Chapter 8 - Operation Panel

 

 

[6] Setting Default Value

DEFAULT

NO YES

DEFAULT

COMPLETE

To enter this mode, power on printer while holding down <FEED> and <LINE> keys simultaneously.

Press <FEED> and <LINE> keys when power on printer, buzzer sounds, and press <LINE> key to move cursor to [YES]. Confirm by pressing <FEED> key.

[7] Setting Service Mode (Default & Service Mode)

To enter this mode, power on printer while holding down <FEED> and <LINE> keys simultaneously.

DEFAULT

NO YES

FEED key

SERVICE MODE

FEED key

SERVICE

LVL SET

FEED key

Tctr [0.0v]

TH [0.0v]

Press <FEED> and <LINE> keys while power on printer, buzzer sounds and press <LINE> key to move cursor to [NO]. Confirm by pressing <FEED> key.

LINE key

Setting sensor level

<LINE> key : proceed to pitch adjustment setting.

<FEED> key : selection of sensor level and threshold level.

39

Image 41
Contents DR300 Copyright 438A Alexandra Road #05-01/02 Alexandra Technopark SingaporeTable of Contents Online Programming …………………………………………… Operation Panel …………………………………………………Appendix B Character Code Table ………………………………………… Appendix a Basic Specification ………………………………………………Serial Interface ………………………………………………… Installation and Operation Instruction Installation and Handling InstructionUnpacking Printer Unit Unpacking Touch Screen Optional Item Accessories Checklist Names of Parts Printer cover Power SwitchSliding Guide Card CoverDisplay Touch Screen / KeypadOperational Panel Unit Card Cover Unit Back Panel Unit Setting Rolled Paper Setting of Label and Carbon RibbonSetting Paper DR300 Operator Manual DR300 Operator Manual Setting Large Diameter Rolled Label Setting Carbon Ribbon Setting Label and Carbon Ribbon Take caution not to trap your finger when closing the cover Pitch Sensor AdjustmentDR300 Operator Manual DR300 Operator Manual Setting of Label and Carbon Ribbon Stop Position Adjustment DR300 Operator Manual Cutting Paper with Perforation Cut Position Adjustment Cutting of LabelCutter Replacement Tag Guide Set Position Basic Usage of StackerTag Guide Position Stack Position Adjustment, Small Tag Less than 35mmSetting Power Supply Power SupplySupply Power Switch off Power SwitchCheck Point Remedy Simple TroubleshootingPaper feeds, but no printing Print image shifts from its position Frequency for maintenance Daily MaintenanceCleaning method for printer parts DR300 Operator Manual PC Card Optional PC CardMemory Card Battery Installation / Exchange DR300 Operator Manual Operation Overview Normal ModeOperation Panel Darkness User ModeSelection for Large Label Size Paper Perform Test PrintingSetting Service Mode Default & Service Mode Setting Default ValueCUT ADJ Pitch ADJPitch a D J SET Time Back ADJCode ADJ Setting Non-Standard ProtocodeSTX 7 B Cursor moves to 1 place after set Price ADJ Currency Font SettingPrice ADJ Dollar Price ADJ YENNON ALL Head CUT Factory ModeFactory Mode NON ALL, HED, CUT Print Online Programming CommandBasic Construction Contents Initial Designation Command Command summary Detail DescriptionEnd Designation Command STXDigit Position Data Description Media Parameter TransmissionBOOKLAND*1 Field Parameter TransmissionMaxi OCR-A OCR-B On-line Mode Field Parameter SummaryINT2OF5 Time Field 24H Field data transmission Graphic data transmission Digit Designated Designated Description Position Normal, calendar, true type fieldDigit Designated Item Designated Description Position DD. MM. Yyyy MM. DD. Yyyy Bookland Bar Code FieldHorizontal Position 001~640 Horizontal position dot Graphic Field Transmission DDD DR300 Operator Manual Digit Designated Item Designated Description Position DR300 Operator Manual DR300 Operator Manual Definition Matrix Size Input Data Size Correction level = DR300 Operator Manual DR300 Operator Manual 2D Bar Code Command QR Code Command DR300 Operator Manual Version Error Numeric Alphanumeric Kanji Binary Correction Version Error Numeric Alphanumeric Kanji Binary Correction Version Error Numeric Alphanumeric Kanji Binary Correction Maxi Code Command XON/OFF Serial InterfaceSerial Interface Ready/Busy XON / Xoff Status 3 Protocol Hex Status TransmissionStatus Summary Table Description DR300 Operator Manual Return Sequence Cancel Demanding Command Reference Flow Chart Basic Specification DR 300 General Specifications Operating Environmental Condition Label & Carbon Ribbon SpecificationDR 300 Software Specifications Printer Main Body Operation Unit DIP-Switch SettingDIP-Switch Setting OFF Status XON-OFF Setting Content Enable Change parameter by touch screen Character Code Table Appendix BDR300 Operator Manual DR300 Operator Manual DR300 Operator Manual
Related manuals
Manual 18 pages 57.39 Kb