SATO DR300 manual OFF Status XON-OFF

Page 91

	DR300 Operator Manual		Appendix A

	Separate sheet 1 (Parity setting)
	2	3	Content
	ON	ON	(Reserved)
	ON	OFF	Odd
	OFF	ON	Even
	OFF	OFF	None
	Separate sheet 2 (Baud rate setting)
	5	6	Content
	ON	ON	2400 bps
	ON	OFF	4800 bps
	OFF	ON	19200 bps
	OFF	OFF	9600 bps
	Separate sheet 3 (Protocol setting)
	7	8	Content
	ON	ON	(Reserved)
	ON	OFF	STATUS 3
	OFF	ON	XON-OFF
	OFF	OFF	Ready/Busy
	DIPSW 2
	No.	Setting	Content
	1	ON	Direct Thermal
		OFF	Thermal Transfer
	2	ON	(Reserved) / Reflecting type sensor
		OFF	(Reserved) / See through type sensor
	3	ON	Head Check, Yes
		OFF	Head Check, No
	4	ON	Hex dump function, Yes
		OFF	Hex dump function, No
	5	ON	Multi items receive mode
		OFF	1 item receive mode
	6	ON	(Reserved)
		OFF	(Reserved)
	7	ON	Size detection, Yes
		OFF	Size detection, Yes
	8	ON	Tear off (Dispense), Yes
		OFF	Tear off (Dispense), No

*Pitch sensor (DSW2-2) is effective only during service, test print. It is void during test print.

89

Image 91

Contents DR300 Copyright 438A Alexandra Road #05-01/02 Alexandra Technopark SingaporeTable of Contents Online Programming …………………………………………… Operation Panel …………………………………………………Serial Interface ………………………………………………… Appendix a Basic Specification ………………………………………………Appendix B Character Code Table ………………………………………… Installation and Operation Instruction Installation and Handling InstructionUnpacking Printer Unit Unpacking Touch Screen Optional Item Accessories Checklist Card Cover Printer cover Power SwitchNames of Parts Sliding GuideOperational Panel Unit Touch Screen / KeypadDisplay Card Cover Unit Back Panel Unit Setting Paper Setting of Label and Carbon RibbonSetting Rolled Paper DR300 Operator Manual DR300 Operator Manual Setting Large Diameter Rolled Label Setting Carbon Ribbon Setting Label and Carbon Ribbon Take caution not to trap your finger when closing the cover Pitch Sensor AdjustmentDR300 Operator Manual DR300 Operator Manual Setting of Label and Carbon Ribbon Stop Position Adjustment DR300 Operator Manual Cutting Paper with Perforation Cut Position Adjustment Cutting of LabelCutter Replacement Tag Guide Set Position Basic Usage of StackerTag Guide Position Stack Position Adjustment, Small Tag Less than 35mmSwitch off Power Switch Power SupplySetting Power Supply Supply PowerCheck Point Remedy Simple TroubleshootingPaper feeds, but no printing Print image shifts from its position Frequency for maintenance Daily MaintenanceCleaning method for printer parts DR300 Operator Manual PC Card Optional PC CardMemory Card Battery Installation / Exchange DR300 Operator Manual Operation Panel Normal ModeOperation Overview Darkness User ModeSelection for Large Label Size Paper Perform Test PrintingSetting Service Mode Default & Service Mode Setting Default ValuePitch a D J Pitch ADJCUT ADJ SET Time Back ADJCode ADJ Setting Non-Standard ProtocodeSTX 7 B Cursor moves to 1 place after set Price ADJ YEN Currency Font SettingPrice ADJ Price ADJ DollarFactory Mode NON ALL, HED, CUT Print Factory ModeNON ALL Head CUT Basic Construction Contents CommandOnline Programming STX Command summary Detail DescriptionInitial Designation Command End Designation CommandDigit Position Data Description Media Parameter TransmissionMaxi Field Parameter TransmissionBOOKLAND*1 OCR-A OCR-B On-line Mode Field Parameter SummaryINT2OF5 Time Field 24H Field data transmission Graphic data transmission Digit Designated Designated Description Position Normal, calendar, true type fieldDigit Designated Item Designated Description Position DD. MM. Yyyy MM. DD. Yyyy Bookland Bar Code FieldHorizontal Position 001~640 Horizontal position dot Graphic Field Transmission DDD DR300 Operator Manual Digit Designated Item Designated Description Position DR300 Operator Manual DR300 Operator Manual Definition Matrix Size Input Data Size Correction level = DR300 Operator Manual DR300 Operator Manual 2D Bar Code Command QR Code Command DR300 Operator Manual Version Error Numeric Alphanumeric Kanji Binary Correction Version Error Numeric Alphanumeric Kanji Binary Correction Version Error Numeric Alphanumeric Kanji Binary Correction Maxi Code Command Serial Interface Serial InterfaceXON/OFF Ready/Busy XON / Xoff Status 3 Protocol Status Summary Table Description Status TransmissionHex DR300 Operator Manual Return Sequence Cancel Demanding Command Reference Flow Chart Basic Specification DR 300 General Specifications Operating Environmental Condition Label & Carbon Ribbon SpecificationDR 300 Software Specifications DIP-Switch Setting DIP-Switch SettingPrinter Main Body Operation Unit OFF Status XON-OFF Setting Content Enable Change parameter by touch screen Character Code Table Appendix BDR300 Operator Manual DR300 Operator Manual DR300 Operator Manual

Related manuals

Manual 18 pages 57.39 Kb