SATO DR300 manual Setting Non-Standard Protocode, Code ADJ

Page 44

DR300 Operator Manual	Chapter 8 - Operation Panel

TME 0 0 : 0 0 8 0 / 0 1 / 0 1

FEED key

TME 0 0 : 0 0 8 0 / 0 1 / 0 1

FEED key

TME 0 0 : 0 0 8 0 / 0 1 / 0 1

FEED key

TME 0 0 : 0 0 8 0 / 0 1 / 0 1

FEED key

SERVICE

LVL SET

**Time (hour, minute, second) can incremented by pressing <LINE> key and confirm by pressing <FEED> key.

[8]Setting Non-Standard Protocode

1)Power on printer while holding down <LINE> and <FEED> keys.

DEFAULT

NO YES

2)Push <FEED> key 2 times and <LINE> key 5 times.

CODE ADJ

3)It advances to non-standard code setting by pushing <FEED>. Key. STX is displayed first. The displayed data at this time becomes presently set code data. (Setting sequence is STX-ETX-ESC-ENQ-CAN)

CODE ADJ

STX : 7 B

42

Image 44

Contents DR300 438A Alexandra Road #05-01/02 Alexandra Technopark Singapore CopyrightTable of Contents Operation Panel ………………………………………………… Online Programming ……………………………………………Appendix B Character Code Table ………………………………………… Appendix a Basic Specification ………………………………………………Serial Interface ………………………………………………… Installation and Handling Instruction Installation and Operation InstructionUnpacking Printer Unit Unpacking Touch Screen Optional Item Accessories Checklist Printer cover Power Switch Names of PartsSliding Guide Card CoverDisplay Touch Screen / KeypadOperational Panel Unit Card Cover Unit Back Panel Unit Setting Rolled Paper Setting of Label and Carbon RibbonSetting Paper DR300 Operator Manual DR300 Operator Manual Setting Large Diameter Rolled Label Setting Carbon Ribbon Setting Label and Carbon Ribbon Pitch Sensor Adjustment Take caution not to trap your finger when closing the coverDR300 Operator Manual DR300 Operator Manual Setting of Label and Carbon Ribbon Stop Position Adjustment DR300 Operator Manual Cut Position Adjustment Cutting of Label Cutting Paper with PerforationCutter Replacement Basic Usage of Stacker Tag Guide Set PositionStack Position Adjustment, Small Tag Less than 35mm Tag Guide PositionPower Supply Setting Power SupplySupply Power Switch off Power SwitchSimple Troubleshooting Check Point RemedyPaper feeds, but no printing Print image shifts from its position Daily Maintenance Frequency for maintenanceCleaning method for printer parts DR300 Operator Manual Optional PC Card PC CardMemory Card Battery Installation / Exchange DR300 Operator Manual Operation Overview Normal ModeOperation Panel User Mode DarknessPerform Test Printing Selection for Large Label Size PaperSetting Default Value Setting Service Mode Default & Service ModeCUT ADJ Pitch ADJPitch a D J Back ADJ SET TimeSetting Non-Standard Protocode Code ADJSTX 7 B Cursor moves to 1 place after set Currency Font Setting Price ADJPrice ADJ Dollar Price ADJ YENNON ALL Head CUT Factory ModeFactory Mode NON ALL, HED, CUT Print Online Programming CommandBasic Construction Contents Command summary Detail Description Initial Designation CommandEnd Designation Command STXMedia Parameter Transmission Digit Position Data DescriptionBOOKLAND*1 Field Parameter TransmissionMaxi On-line Mode Field Parameter Summary OCR-A OCR-BINT2OF5 Time Field 24H Field data transmission Graphic data transmission Normal, calendar, true type field Digit Designated Designated Description PositionDigit Designated Item Designated Description Position DD. MM. Yyyy MM. DD. Yyyy Bar Code Field BooklandHorizontal Position 001~640 Horizontal position dot Graphic Field Transmission DDD DR300 Operator Manual Digit Designated Item Designated Description Position DR300 Operator Manual DR300 Operator Manual Definition Matrix Size Input Data Size Correction level = DR300 Operator Manual DR300 Operator Manual 2D Bar Code Command QR Code Command DR300 Operator Manual Version Error Numeric Alphanumeric Kanji Binary Correction Version Error Numeric Alphanumeric Kanji Binary Correction Version Error Numeric Alphanumeric Kanji Binary Correction Maxi Code Command XON/OFF Serial InterfaceSerial Interface Ready/Busy XON / Xoff Status 3 Protocol Hex Status TransmissionStatus Summary Table Description DR300 Operator Manual Return Sequence Cancel Demanding Command Reference Flow Chart Basic Specification DR 300 General Specifications Label & Carbon Ribbon Specification Operating Environmental ConditionDR 300 Software Specifications Printer Main Body Operation Unit DIP-Switch SettingDIP-Switch Setting OFF Status XON-OFF Setting Content Enable Change parameter by touch screen Appendix B Character Code TableDR300 Operator Manual DR300 Operator Manual DR300 Operator Manual

Related manuals

Manual 18 pages 57.39 Kb