Xantrex Technology XDI2048 manual How to Setup For the First Time, Hardware Setup

Page 58

Remote Communication & Monitoring

How to Setup For the First Time

Hardware Setup

In order to communicate to the XDI Ethernet for the first time, you will need a CAT5/CAT5e cable and a computer with an Ethernet adapter installed.

Setting up to configure for the first time:

1.Wire up the rack mount assembly as stated in Chapter 2.

2.Connect to the unit as shown in Figure 4-2, “First Time Setup Connections” on page 4–4.

3.Turn on the inverter.

4.Configure the computer’s Ethernet adapter settings (contact Network Administrator).

5.Open your Web browser and go to the default IP address (Table 4-1).

Special cross-over cable required

PC

Inverter

Network Setup (PC to Inverter)

OR

PC

Hub

Inverter

Network Setup (PC to Hub to Inverter)

Figure 4-2First Time Setup Connections

4-4	TM-DIOP-01XN-01

Image 58

Contents XDI2048 2kVA/1.5kW Page Xantrex Datacom Inverter Date and Revision Audience PurposeScope OrganizationConventions Used Related InformationImportant Safety Instructions Page Contents Inverter Module Installation and Operation Troubleshooting Remote Communication & MonitoringSpecifications Warranty and Product InformationFigures Xii Tables Xiv Introduction Inverter Information Features and OptionsDescription Features and Functions Ethernet InformationPart Number and Ordering Information XDI2048HV-RMAssembly Initial Inspection Packing ListPackaging for Shipping or Storage 2Shipping or Storage Carton LabelIntroduction Rack Mount Frame Rear ViewInstallation Into Cabinet Style Equipment Racks Location, Mounting and VentilationInstallation into Relay Racks Installing into Relay RacksInput Connector and Cables DC Input PowerDC Input Wire Connection Connecting the Input Wires Load Wiring AC Load and Signal Line ConnectionAC Output Connector AC Output Voltage WireLoad Connection User Line Connection OverviewUser Line Connection User Line ConnectorUser Line Wiring User Line ConnectionSpecifications CAN/SYNC ConnectorCAN/SYNC Connection CAN/SYNC Pin-out CAN/SYNC WiringTerminals Function Parallel Operation Connection SchemesStand-Alone Operation ConnectionParallel Operation Split-Phase Operation Split Phase OperationLoad Terminal Voltage Wiring Output Configuration Three Phase Operation33-Phase Configurations Terminals Model VoltagePhase Synchronization and Signal Wiring 103-Phase Sync ConnectionPhase, 3-Wire Delta Output Wiring Phase, 3-Wire Y-Connection Output WiringPhase, 4-Wire Y-Connection Output Wiring Ethernet PortPage Operation Installation into Rack Mount Frame Installing an Inverter into a Rack 2Inverter Front PanelTheory of Operation Operation of Inverter ModuleSystem Startup Standby Mode Cooling FansFront Panel 2User Line PinsUser Interface User LinesInput Voltage Protection Protections and AlarmsOverview Output Voltage ProtectionOverload Protection 3Overload curveShort-circuit Protection Over Temperature Protection OTPInternal Diagnostics Over-Current protectionFuses and Grounding Output AC AlarmIncorrect Connection Protection Maintenance To Clear an Alarm4Replacing the Fan Filters Monitoring Web-enabled User Interface Initial SetupInitial Setup Ethernet Interface PCBHow to Setup For the First Time Hardware Setup1Default Settings Ethernet SetupSetting Default Value 2User Configured Settings ResettingSettingValue Setting Reset Value 3Reset SettingsRemoving Unit’s Top Cover Ethernet Reset Jumper Operating Instructions Network Connection5Network Setup Using Dhcp What Power On DoesPassword 6Password Confirmation BoxesAutomatic Power-On Email How to Use the Web InterfaceManage Object DescriptionSetup 8Setup Page of Web Interface5Setup Page of Web Interface Monitor 9Monitor Page of Web Interface6Monitor Page of Web Interface Automatic Shutdown Email Code Fault DescriptionShutdown Code TM-DIOP-01XN-01 Troubleshooting Emergency Shutdown User DiagnosticsUnusual or Erratic Operation 1Inverter Diagnostics Diagnostic GuideSymptom Check 2Ethernet Diagnostics Specifications Inverter Specifications Electrical SpecificationsInverter Specifications Environmental Specifications Regulatory ApprovalsMechanical Specifications Inverter and Rack Mount Frame Dimensions Figure A-1Ethernet Specifications Page Warranty and Product Information WarrantyDisclaimer ProductReturn Material Authorization Policy ExclusionsOut of Warranty Service Return ProcedureInformation About Your System Page Xantrex Technology Inc