Fujitsu PG-FCS103, PG-FCS102, BX620 manual Installing a 1Gbit/s Ethernet I/O Module

Page 15

2 Installing a 1Gbit/s Ethernet I/O Module

This chapter explains the installation procedure in the server blade.

WARNING

• When installing or removing this product, make sure to remove the server blade from the chassis. Failure to do so may cause electric shock.

For details on how to remove the server blade from the chassis, refer to "Blade Server System Unit Hardware Guide".

CAUTION

•The circuit boards and soldered parts of internal options are exposed. They can be damaged by static electricity. Before handling them, first touch a metal part of the server blade to discharge static electricity from your body.

•Do not touch the circuitry on boards or soldered parts. Hold the metallic areas or the edges of the circuit boards.

•These products are susceptible to static electricity. Place them on conductive pads or keep them in their packaging as long as they are not necessary.

2 Installing a 1Gbit/s Ethernet I/O Module 115

Image 15

Contents 101 Before Reading This ManualCD-ROM drive\Setup.exe SymbolsEntering commands Keys Symbols DefinitionAbbreviations 103Product names Expressions and abbreviations Handling this product Recycle104 Contents Specifications Overview106 Functionality and Features FeaturesFunctional Description TCP Offload Engine TOE Broadcom Advanced Control Suite 2 BACS2108 Types of Teams Load Balancing and Fault ToleranceTeaming Function Broadcom Advanced Server Program Bsap Overview110 Smart Load Balancing and FailoverLink Aggregation 802.3ad Generic Trunking FEC/GEC/802.3ad-Draft StaticWindows Server With SNP SLB Auto-Fallback DisableVlan Overview Virtual LAN FunctionLiveLink Teaming and Large Send Offload/Checksum Offload SupportComponent Description PC #3 PC #5. Tagging is not enabled on PC #3 switch portAdding VLANs to Teams 114Installing a 1Gbit/s Ethernet I/O Module 116 Installing in a Server BladeInstallation Position of the 1Gbit/s Ethernet I/O Module Installation Procedure for the 1Gbit/s Ethernet I/O ModuleSecure the 1Gbit/s Ethernet I/O Module with the screws Install the 1Gbit/s Ethernet I/O ModuleInstall the server blade to the chassis Remove the top coverInstalling the Driver Software Installing the LAN DriversClick Next Glossary Broadcom Gigabit Ethernet Overview120 Teaming and Network Addresses Teaming ConceptsTeaming and Network Addresses Network Addressing122 Types of TeamsBroadcom Gigabit Ethernet Teaming Services 124 Link Aggregation Ieee 802.3ad LacpGeneric Trunking Software ComponentsSoftware Broadcom Name Windows File Name Component Hardware Requirements126 Broadcom Teaming Software ComponentSupported Features by Team Type Configuring Teaming128 Selecting a Team Type Process for Selecting a Team TypeYes Intermediate Driver Teaming MechanismsArchitecture 130Inbound Traffic Flow SLB Only Outbound Traffic FlowProtocol Support 132Or the streams may look like this Switch-Independent Types of TeamsPerformance Switch-Dependent Generic Static Trunking134 Dynamic Trunking Ieee 802.3ad Link Aggregation Feature Attribute 136Outgoing packet management 100 Incoming/outgoing Same speed Speeds Supported for Each Type of TeamType of Team Link Speed Traffic Direction Speed Support 10/100/1000 Incoming/outgoing Mixed speedAdapter Properties Supported by Teaming Virtual Adapter Wake on LAN Preboot Execution environment PXETeaming and Other Advanced Networking Properties 138Jumbo Frames Checksum OffloadIeee 802.1p QoS Tagging Large Send OffloadGeneral Network Considerations Teaming Across SwitchesSwitch-Link Fault Tolerance Preboot Execution EnvironmentRed ARP TableBlue 100=49C9 SLB Team 102=5ECA 8283142 Spanning Tree Algorithm 144 Topology Change Notice TCNPort Fast/Edge Port Layer 3 Routing/SwitchingTeaming with Hubs for troubleshooting purposes only Hub Usage in Teaming Network ConfigurationsTeaming with Microsoft NLB/WLBS SLB TeamsSLB Team Connected to a Single Hub Generic and Dynamic Trunking FEC/GEC/IEEE 802.3adTeaming Configuration Tips Troubleshooting Teaming ProblemsQuestion Answer Troubleshooting GuidelinesFrequently Asked Questions 148Adapter Be configured on the same server? ServerIs restored fallback? It must be upgraded using the Setup installer150 Message Cause Corrective Action Number Event Log MessagesWindows System Event Log messages Base Driver Physical Adapter/MiniportDuplex settings Medium not supported Reboot the operating152 Unable to register with Driver cannot Unload any Ndis Intermediate Driver Virtual Adapter/TeamUnspecified failure during Intermediate Driver Event Log MessagesSystem on which it is Support the operating Release notes and installSuccessfully enabled a Only Interface 154Message Cause Corrective Action Number BACS2 Overview 156Third pane contains the Menu bar Only available with this product J5.4.8 Licensespg.175 Types of Information Provided by BACS2Function Details Licenses158 Installing the BACS2Installer starts up For Windows Server 2003License agreement window appears 160 Custom Set up window appearsFor Windows Server 2003, Windows 2000 Server CD-ROM drive \PROGRAMS\GENERAL\Broadcom\MgmtApps\setup.exe162 Setting of BACS2Starting BACS2 Vital SignFollowing network status information is provided Network StatusWith headers appended to them By the host CPU164 Team StatusRange from 2 to Memory Address ResourcesFollowing information can be checked on the Resources tab Function number for the second port is Interrupt RequestHardware 166Following information can be checked on the Hardware tab 802.1p QOS Not enable QoS. Otherwise, problems may occurAdvanced Following information can be checked on the Advanced tab168 Sets the speed at 10 Mbit/s and the mode to Full-Duplex Locally AdministeredNot Present default Administered address include the followingDiagnostics Network Test170 Identifying the adapter Control RegistersStatistics General Statistics172 Ieee 802.3 Statistics 174 Command Length = MAC Rx w/ PauseCommand Custom StatisticsLicenses 176 Configuring TeamingUsing the Broadcom Teaming Wizard Creating and Modifying a Team Using the Teaming WizardOn the BACS2 Tools menu, click Create a Team 178 Broadcom Advanced Control Suite 2 BACS2 Select the standby member from the list of adapters Broadcom Advanced Control Suite 2 BACS2 Type the Vlan name and then click Next 182 To tag the VLAN, click Tagged and then click Next Value must be between 1 Type the Vlan tag value and then click NextClick Yes to add another Vlan and then click Next 184Click Finish to commit the changes Click the BACS2 Tools menu → Create a Team Using Expert ModeTo work without the wizard, click Expert Mode Creating a TeamBroadcom Advanced Control Suite 2 BACS2 Configure the team IP address Modifying a Team188 Following shows how to modify a team Adding a VlanWizard Welcome screen appears Type the Vlan ID and Vlan name, and click Apply Viewing Vlan Properties and Running Vlan TestsClick the Tools menu → Configure a Team Deleting a VlanClick Remove Vlan Click Apply 192 Following shows how to configure a LiveLinkRepeat for each of the other listed team members Click Apply Configuring LiveLink in VLAN-tagged EnvironmentsViewing the Team Properties and Statistics Saving and Restoring a ConfigurationFollowing shows how to save a configuration Following shows how to restore a configurationAppendix a Contact 196 Primergy