Fujitsu PG-FCS103, PG-FCS102, BX620 manual Port Fast/Edge Port, Layer 3 Routing/Switching

Page 45

4.8.5Port Fast/Edge Port

To reduce the effect of TCNs on the network (for example, increasing flooding on switch ports), end nodes that are powered on/off often should use the Port Fast or Edge Port setting on the switch port they are attached to. Port Fast or Edge Port is a command that is applied to specific ports and has the following effects:

Ports coming from link down to link up will be put in the forwarding STP mode instead of going from listening to learning and then to forwarding. STP is still running on these ports.

The switch does not generate a Topology Change Notice when the port is going up or down.

4.8.6Layer 3 Routing/Switching

The switch that the teamed ports are connected to must not be a Layer 3 switch or router. The ports in the team must be in the same network.

4.8.7Teaming with Hubs (for troubleshooting purposes only)

SLB teaming can be used with 10/100 hubs, but it is only recommended for troubleshooting purposes, such as connecting a network analyzer in the event that switch port mirroring is not an option.

4.8.8Hub Usage in Teaming Network Configurations

Although the use of hubs in network topologies is functional in some situations, it is important to consider the throughput ramifications when doing so. Network hubs have a maximum of 100 Mbps half-duplex link speed, which severely degrades performance in either a Gigabit or 100 Mbps switched-network configuration. Hub bandwidth is shared among all connected devices; as a result, when more devices are connected to the hub, the bandwidth available to any single device connected to the hub is reduced in direct proportion to the number of devices connected to the hub.

It is not recommended to connect team members to hubs; only switches should be used to connect to teamed ports. An SLB team, however, can be connected directly to a hub for troubleshooting purposes. Other team types can result in a loss of connectivity if specific failures occur and should not be used with hubs.

E

4 Broadcom Gigabit Ethernet Teaming Services 145

Image 45
Contents 101 Before Reading This ManualEntering commands Keys SymbolsSymbols Definition CD-ROM drive\Setup.exeAbbreviations 103Product names Expressions and abbreviations Handling this product Recycle104 Contents Specifications Overview106 Functionality and Features FeaturesFunctional Description TCP Offload Engine TOE Broadcom Advanced Control Suite 2 BACS2108 Teaming Function Load Balancing and Fault ToleranceBroadcom Advanced Server Program Bsap Overview Types of TeamsLink Aggregation 802.3ad Smart Load Balancing and FailoverGeneric Trunking FEC/GEC/802.3ad-Draft Static 110Windows Server With SNP SLB Auto-Fallback DisableLiveLink Virtual LAN FunctionTeaming and Large Send Offload/Checksum Offload Support Vlan OverviewComponent Description Adding VLANs to Teams PC #5. Tagging is not enabled on PC #3 switch port114 PC #3Installing a 1Gbit/s Ethernet I/O Module Installation Position of the 1Gbit/s Ethernet I/O Module Installing in a Server BladeInstallation Procedure for the 1Gbit/s Ethernet I/O Module 116Install the server blade to the chassis Install the 1Gbit/s Ethernet I/O ModuleRemove the top cover Secure the 1Gbit/s Ethernet I/O Module with the screwsInstalling the Driver Software Installing the LAN DriversClick Next Glossary Broadcom Gigabit Ethernet Overview120 Teaming and Network Addresses Teaming ConceptsNetwork Addressing Teaming and Network Addresses122 Types of TeamsBroadcom Gigabit Ethernet Teaming Services 124 Link Aggregation Ieee 802.3ad LacpGeneric Trunking Software Components126 Hardware RequirementsBroadcom Teaming Software Component Software Broadcom Name Windows File Name ComponentSupported Features by Team Type Configuring Teaming128 Selecting a Team Type Process for Selecting a Team TypeYes Architecture Teaming Mechanisms130 Intermediate DriverInbound Traffic Flow SLB Only Outbound Traffic FlowProtocol Support 132Or the streams may look like this Switch-Independent Types of TeamsPerformance Switch-Dependent Generic Static Trunking134 Dynamic Trunking Ieee 802.3ad Link Aggregation Feature Attribute 136Outgoing packet management Type of Team Link Speed Traffic Direction Speed Support Speeds Supported for Each Type of Team10/100/1000 Incoming/outgoing Mixed speed 100 Incoming/outgoing Same speedTeaming and Other Advanced Networking Properties Wake on LAN Preboot Execution environment PXE138 Adapter Properties Supported by Teaming Virtual AdapterIeee 802.1p QoS Tagging Checksum OffloadLarge Send Offload Jumbo FramesSwitch-Link Fault Tolerance Teaming Across SwitchesPreboot Execution Environment General Network ConsiderationsBlue 100=49C9 SLB Team 102=5ECA ARP Table8283 Red142 Spanning Tree Algorithm 144 Topology Change Notice TCNTeaming with Hubs for troubleshooting purposes only Layer 3 Routing/SwitchingHub Usage in Teaming Network Configurations Port Fast/Edge PortSLB Team Connected to a Single Hub SLB TeamsGeneric and Dynamic Trunking FEC/GEC/IEEE 802.3ad Teaming with Microsoft NLB/WLBSTeaming Configuration Tips Troubleshooting Teaming ProblemsFrequently Asked Questions Troubleshooting Guidelines148 Question AnswerIs restored fallback? Be configured on the same server? ServerIt must be upgraded using the Setup installer Adapter150 Windows System Event Log messages Event Log MessagesBase Driver Physical Adapter/Miniport Message Cause Corrective Action NumberDuplex settings Medium not supported Reboot the operating152 Unspecified failure during Intermediate Driver Virtual Adapter/TeamIntermediate Driver Event Log Messages Unable to register with Driver cannot Unload any NdisSuccessfully enabled a Only Interface Support the operating Release notes and install154 System on which it isMessage Cause Corrective Action Number BACS2 Overview 156Third pane contains the Menu bar Function Details Types of Information Provided by BACS2Licenses Only available with this product J5.4.8 Licensespg.175158 Installing the BACS2Installer starts up For Windows Server 2003License agreement window appears 160 Custom Set up window appearsFor Windows Server 2003, Windows 2000 Server CD-ROM drive \PROGRAMS\GENERAL\Broadcom\MgmtApps\setup.exeStarting BACS2 Setting of BACS2Vital Sign 162With headers appended to them Network StatusBy the host CPU Following network status information is provided164 Team StatusFollowing information can be checked on the Resources tab ResourcesFunction number for the second port is Interrupt Request Range from 2 to Memory AddressHardware 166Following information can be checked on the Hardware tab Advanced Not enable QoS. Otherwise, problems may occurFollowing information can be checked on the Advanced tab 802.1p QOS168 Not Present default Locally AdministeredAdministered address include the following Sets the speed at 10 Mbit/s and the mode to Full-DuplexDiagnostics Network Test170 Identifying the adapter Control RegistersStatistics General Statistics172 Ieee 802.3 Statistics Command Command Length = MAC Rx w/ PauseCustom Statistics 174Licenses 176 Configuring TeamingUsing the Broadcom Teaming Wizard Creating and Modifying a Team Using the Teaming WizardOn the BACS2 Tools menu, click Create a Team 178 Broadcom Advanced Control Suite 2 BACS2 Select the standby member from the list of adapters Broadcom Advanced Control Suite 2 BACS2 Type the Vlan name and then click Next 182 To tag the VLAN, click Tagged and then click Next Click Yes to add another Vlan and then click Next Type the Vlan tag value and then click Next184 Value must be between 1Click Finish to commit the changes To work without the wizard, click Expert Mode Using Expert ModeCreating a Team Click the BACS2 Tools menu → Create a TeamBroadcom Advanced Control Suite 2 BACS2 Configure the team IP address Modifying a Team188 Following shows how to modify a team Adding a VlanWizard Welcome screen appears Type the Vlan ID and Vlan name, and click Apply Viewing Vlan Properties and Running Vlan TestsClick the Tools menu → Configure a Team Deleting a VlanClick Remove Vlan Click Apply 192 Following shows how to configure a LiveLinkRepeat for each of the other listed team members Click Apply Configuring LiveLink in VLAN-tagged EnvironmentsFollowing shows how to save a configuration Saving and Restoring a ConfigurationFollowing shows how to restore a configuration Viewing the Team Properties and StatisticsAppendix a Contact 196 Primergy