Fujitsu PG-FCS103, PG-FCS102, BX620 manual 136, Feature Attribute, Outgoing packet management

Page 36

4.6Attributes of the Features Associated with Each Type of Team

The attributes of the features associated with each type of team are summarized below.

• Smart Load BalancingTM

Feature	Attribute
User interface	Broadcom Advanced Control Suite 2 (BACS2)

Number of teams	Maximum 4

Number of adapters per team	Maximum 8

Hot replace	Yes

Hot add	Yes

Hot remove	Yes

Link speed support	Different speeds

Frame protocol	IP

Incoming packet management	BASP

Outgoing packet management	BASP

LiveLink support	Yes

Failover event	Loss of link

Failover time	<500 ms

Fallback time	1.5 s(*1) (approximate)
MAC address	Different

Multivendor teaming	Yes

*1: Make sure that Port Fast or Edge Port is enabled.

• Generic Trunking

Feature	Attribute
User interface	Broadcom Advanced Control Suite 2 (BACS2)

Number of teams	Maximum 4

Number of adapters per team	Maximum 8

Hot replace	Yes

Hot add	Yes

Hot remove	Yes

Link speed support	Different speeds(*1)
Frame protocol	All

Incoming packet management	Switch

Outgoing packet management	BASP

Failover event	Loss of link only

Failover time	<500 ms

Fallback time	1.5 s(*2) (approximate)

136

Image 36

Contents Before Reading This Manual 101Symbols Entering commands KeysSymbols Definition CD-ROM drive\Setup.exeAbbreviations 103Product names Expressions and abbreviations Handling this product Recycle104 Contents Specifications Overview106 Functionality and Features FeaturesFunctional Description TCP Offload Engine TOE Broadcom Advanced Control Suite 2 BACS2108 Load Balancing and Fault Tolerance Teaming FunctionBroadcom Advanced Server Program Bsap Overview Types of TeamsSmart Load Balancing and Failover Link Aggregation 802.3adGeneric Trunking FEC/GEC/802.3ad-Draft Static 110SLB Auto-Fallback Disable Windows Server With SNPVirtual LAN Function LiveLinkTeaming and Large Send Offload/Checksum Offload Support Vlan OverviewComponent Description PC #5. Tagging is not enabled on PC #3 switch port Adding VLANs to Teams114 PC #3Installing a 1Gbit/s Ethernet I/O Module Installing in a Server Blade Installation Position of the 1Gbit/s Ethernet I/O ModuleInstallation Procedure for the 1Gbit/s Ethernet I/O Module 116Install the 1Gbit/s Ethernet I/O Module Install the server blade to the chassisRemove the top cover Secure the 1Gbit/s Ethernet I/O Module with the screwsInstalling the Driver Software Installing the LAN DriversClick Next Broadcom Gigabit Ethernet Overview Glossary120 Teaming Concepts Teaming and Network AddressesNetwork Addressing Teaming and Network AddressesTypes of Teams 122Broadcom Gigabit Ethernet Teaming Services Link Aggregation Ieee 802.3ad Lacp 124Software Components Generic TrunkingHardware Requirements 126Broadcom Teaming Software Component Software Broadcom Name Windows File Name ComponentConfiguring Teaming Supported Features by Team Type128 Selecting a Team Type Process for Selecting a Team TypeYes Teaming Mechanisms Architecture130 Intermediate DriverOutbound Traffic Flow Inbound Traffic Flow SLB OnlyProtocol Support 132Or the streams may look like this Switch-Independent Types of TeamsPerformance Switch-Dependent Generic Static Trunking134 Dynamic Trunking Ieee 802.3ad Link Aggregation Feature Attribute 136Outgoing packet management Speeds Supported for Each Type of Team Type of Team Link Speed Traffic Direction Speed Support10/100/1000 Incoming/outgoing Mixed speed 100 Incoming/outgoing Same speedWake on LAN Preboot Execution environment PXE Teaming and Other Advanced Networking Properties138 Adapter Properties Supported by Teaming Virtual AdapterChecksum Offload Ieee 802.1p QoS TaggingLarge Send Offload Jumbo FramesTeaming Across Switches Switch-Link Fault TolerancePreboot Execution Environment General Network ConsiderationsARP Table Blue 100=49C9 SLB Team 102=5ECA8283 Red142 Spanning Tree Algorithm Topology Change Notice TCN 144Layer 3 Routing/Switching Teaming with Hubs for troubleshooting purposes onlyHub Usage in Teaming Network Configurations Port Fast/Edge PortSLB Teams SLB Team Connected to a Single HubGeneric and Dynamic Trunking FEC/GEC/IEEE 802.3ad Teaming with Microsoft NLB/WLBSTroubleshooting Teaming Problems Teaming Configuration TipsTroubleshooting Guidelines Frequently Asked Questions148 Question AnswerBe configured on the same server? Server Is restored fallback?It must be upgraded using the Setup installer Adapter150 Event Log Messages Windows System Event Log messagesBase Driver Physical Adapter/Miniport Message Cause Corrective Action NumberDuplex settings Medium not supported Reboot the operating152 Intermediate Driver Virtual Adapter/Team Unspecified failure duringIntermediate Driver Event Log Messages Unable to register with Driver cannot Unload any NdisSupport the operating Release notes and install Successfully enabled a Only Interface154 System on which it isMessage Cause Corrective Action Number BACS2 Overview 156Third pane contains the Menu bar Types of Information Provided by BACS2 Function DetailsLicenses Only available with this product J5.4.8 Licensespg.175Installing the BACS2 158Installer starts up For Windows Server 2003License agreement window appears Custom Set up window appears 160CD-ROM drive \PROGRAMS\GENERAL\Broadcom\MgmtApps\setup.exe For Windows Server 2003, Windows 2000 ServerSetting of BACS2 Starting BACS2Vital Sign 162Network Status With headers appended to themBy the host CPU Following network status information is providedTeam Status 164Resources Following information can be checked on the Resources tabFunction number for the second port is Interrupt Request Range from 2 to Memory AddressHardware 166Following information can be checked on the Hardware tab Not enable QoS. Otherwise, problems may occur AdvancedFollowing information can be checked on the Advanced tab 802.1p QOS168 Locally Administered Not Present defaultAdministered address include the following Sets the speed at 10 Mbit/s and the mode to Full-DuplexDiagnostics Network Test170 Control Registers Identifying the adapterStatistics General Statistics172 Ieee 802.3 Statistics Command Length = MAC Rx w/ Pause CommandCustom Statistics 174Licenses Configuring Teaming 176Using the Broadcom Teaming Wizard Creating and Modifying a Team Using the Teaming WizardOn the BACS2 Tools menu, click Create a Team 178 Broadcom Advanced Control Suite 2 BACS2 Select the standby member from the list of adapters Broadcom Advanced Control Suite 2 BACS2 Type the Vlan name and then click Next 182 To tag the VLAN, click Tagged and then click Next Type the Vlan tag value and then click Next Click Yes to add another Vlan and then click Next184 Value must be between 1Click Finish to commit the changes Using Expert Mode To work without the wizard, click Expert ModeCreating a Team Click the BACS2 Tools menu → Create a TeamBroadcom Advanced Control Suite 2 BACS2 Configure the team IP address Modifying a Team188 Following shows how to modify a team Adding a VlanWizard Welcome screen appears Viewing Vlan Properties and Running Vlan Tests Type the Vlan ID and Vlan name, and click ApplyClick the Tools menu → Configure a Team Deleting a VlanClick Remove Vlan Click Apply Following shows how to configure a LiveLink 192Configuring LiveLink in VLAN-tagged Environments Repeat for each of the other listed team members Click ApplySaving and Restoring a Configuration Following shows how to save a configurationFollowing shows how to restore a configuration Viewing the Team Properties and StatisticsAppendix a Contact 196 Primergy