Fujitsu PG-FCS102, PG-FCS103, BX620 manual Team Status, 164

Page 64

Team Status

The team status is indicated by the appearance of the icons representing the team and the team members. If the adapter icon shows only the adapter, the adapter is connected to a network, but is not correctly participating in the team, which corresponds to a Not Active BASP state. This condition does not apply to an adapter that is a standby member of a team. The standby adapter may be working properly even though it is Not Active.

If the adapter icon shows a superimposed running yellow figure, the adapter is connected and participating in the team correctly, which corresponds to an Active BASP state.

If the adapter icon shows a superimposed red letter X, the adapter is not connected to the network.

164

Image 64

Contents Before Reading This Manual 101Symbols Entering commands KeysSymbols Definition CD-ROM drive\Setup.exe103 AbbreviationsProduct names Expressions and abbreviations Recycle Handling this product104 Contents Overview Specifications106 Features Functionality and FeaturesFunctional Description Broadcom Advanced Control Suite 2 BACS2 TCP Offload Engine TOE108 Load Balancing and Fault Tolerance Teaming FunctionBroadcom Advanced Server Program Bsap Overview Types of TeamsSmart Load Balancing and Failover Link Aggregation 802.3adGeneric Trunking FEC/GEC/802.3ad-Draft Static 110SLB Auto-Fallback Disable Windows Server With SNPVirtual LAN Function LiveLinkTeaming and Large Send Offload/Checksum Offload Support Vlan OverviewComponent Description PC #5. Tagging is not enabled on PC #3 switch port Adding VLANs to Teams114 PC #3Installing a 1Gbit/s Ethernet I/O Module Installing in a Server Blade Installation Position of the 1Gbit/s Ethernet I/O ModuleInstallation Procedure for the 1Gbit/s Ethernet I/O Module 116Install the 1Gbit/s Ethernet I/O Module Install the server blade to the chassisRemove the top cover Secure the 1Gbit/s Ethernet I/O Module with the screwsInstalling the LAN Drivers Installing the Driver SoftwareClick Next Broadcom Gigabit Ethernet Overview Glossary120 Teaming Concepts Teaming and Network AddressesNetwork Addressing Teaming and Network AddressesTypes of Teams 122Broadcom Gigabit Ethernet Teaming Services Link Aggregation Ieee 802.3ad Lacp 124Software Components Generic TrunkingHardware Requirements 126Broadcom Teaming Software Component Software Broadcom Name Windows File Name ComponentConfiguring Teaming Supported Features by Team Type128 Process for Selecting a Team Type Selecting a Team TypeYes Teaming Mechanisms Architecture130 Intermediate DriverOutbound Traffic Flow Inbound Traffic Flow SLB Only132 Protocol SupportOr the streams may look like this Types of Teams Switch-IndependentPerformance Generic Static Trunking Switch-Dependent134 Dynamic Trunking Ieee 802.3ad Link Aggregation 136 Feature AttributeOutgoing packet management Speeds Supported for Each Type of Team Type of Team Link Speed Traffic Direction Speed Support10/100/1000 Incoming/outgoing Mixed speed 100 Incoming/outgoing Same speedWake on LAN Preboot Execution environment PXE Teaming and Other Advanced Networking Properties138 Adapter Properties Supported by Teaming Virtual AdapterChecksum Offload Ieee 802.1p QoS TaggingLarge Send Offload Jumbo FramesTeaming Across Switches Switch-Link Fault TolerancePreboot Execution Environment General Network ConsiderationsARP Table Blue 100=49C9 SLB Team 102=5ECA8283 Red142 Spanning Tree Algorithm Topology Change Notice TCN 144Layer 3 Routing/Switching Teaming with Hubs for troubleshooting purposes onlyHub Usage in Teaming Network Configurations Port Fast/Edge PortSLB Teams SLB Team Connected to a Single HubGeneric and Dynamic Trunking FEC/GEC/IEEE 802.3ad Teaming with Microsoft NLB/WLBSTroubleshooting Teaming Problems Teaming Configuration TipsTroubleshooting Guidelines Frequently Asked Questions148 Question AnswerBe configured on the same server? Server Is restored fallback?It must be upgraded using the Setup installer Adapter150 Event Log Messages Windows System Event Log messagesBase Driver Physical Adapter/Miniport Message Cause Corrective Action NumberReboot the operating Duplex settings Medium not supported152 Intermediate Driver Virtual Adapter/Team Unspecified failure duringIntermediate Driver Event Log Messages Unable to register with Driver cannot Unload any NdisSupport the operating Release notes and install Successfully enabled a Only Interface154 System on which it isMessage Cause Corrective Action Number 156 BACS2 OverviewThird pane contains the Menu bar Types of Information Provided by BACS2 Function DetailsLicenses Only available with this product J5.4.8 Licensespg.175Installing the BACS2 158For Windows Server 2003 Installer starts upLicense agreement window appears Custom Set up window appears 160CD-ROM drive \PROGRAMS\GENERAL\Broadcom\MgmtApps\setup.exe For Windows Server 2003, Windows 2000 ServerSetting of BACS2 Starting BACS2Vital Sign 162Network Status With headers appended to themBy the host CPU Following network status information is providedTeam Status 164Resources Following information can be checked on the Resources tabFunction number for the second port is Interrupt Request Range from 2 to Memory Address166 HardwareFollowing information can be checked on the Hardware tab Not enable QoS. Otherwise, problems may occur AdvancedFollowing information can be checked on the Advanced tab 802.1p QOS168 Locally Administered Not Present defaultAdministered address include the following Sets the speed at 10 Mbit/s and the mode to Full-DuplexNetwork Test Diagnostics170 Control Registers Identifying the adapterGeneral Statistics Statistics172 Ieee 802.3 Statistics Command Length = MAC Rx w/ Pause CommandCustom Statistics 174Licenses Configuring Teaming 176Creating and Modifying a Team Using the Teaming Wizard Using the Broadcom Teaming WizardOn the BACS2 Tools menu, click Create a Team 178 Broadcom Advanced Control Suite 2 BACS2 Select the standby member from the list of adapters Broadcom Advanced Control Suite 2 BACS2 Type the Vlan name and then click Next 182 To tag the VLAN, click Tagged and then click Next Type the Vlan tag value and then click Next Click Yes to add another Vlan and then click Next184 Value must be between 1Click Finish to commit the changes Using Expert Mode To work without the wizard, click Expert ModeCreating a Team Click the BACS2 Tools menu → Create a TeamBroadcom Advanced Control Suite 2 BACS2 Modifying a Team Configure the team IP address188 Adding a Vlan Following shows how to modify a teamWizard Welcome screen appears Viewing Vlan Properties and Running Vlan Tests Type the Vlan ID and Vlan name, and click ApplyDeleting a Vlan Click the Tools menu → Configure a TeamClick Remove Vlan Click Apply Following shows how to configure a LiveLink 192Configuring LiveLink in VLAN-tagged Environments Repeat for each of the other listed team members Click ApplySaving and Restoring a Configuration Following shows how to save a configurationFollowing shows how to restore a configuration Viewing the Team Properties and StatisticsAppendix a Contact 196 Primergy