Cisco Systems ME 6500 manual Green-Source AC voltage is OK. Input voltage is 82 VAC or

Page 74

Appendix A Power Supply Specifications

400 W AC-Input Power Supply

 

 

 

 

Table A-2

400 W AC-Input Power Supply Specifications (continued)

 

 

 

 

 

 

 

 

 

 

 

Specification

 

Description

 

 

 

 

 

 

 

 

 

 

Branch circuit requirement

Each chassis power supply should have its own dedicated, fused-branch

 

 

 

 

 

 

circuit:

 

 

 

 

 

 

For North America—10 A

 

 

 

 

 

 

For International—Circuits sized to local and national codes

 

 

 

 

 

 

All AC power supply inputs are fully isolated.

 

 

 

 

 

 

Source AC can be out of phase between multiple power supplies

 

 

 

 

 

 

in the same chassis, which means that PS1 can be operating

 

 

 

 

 

 

from phase A and PS2 can be operating from phase B.

 

 

 

 

 

 

For high-line operation, the power supply operates with the hot

 

 

 

 

 

 

conductor wired to a source AC phase and the neutral conductor

 

 

 

 

 

 

wired either to ground or to another source AC phase as long as

 

 

 

 

 

 

the net input voltage is in the range of 170 to 264 VAC.

 

 

 

 

 

 

 

 

 

 

Power supply output

34.00 A @ +12 VDC

 

 

 

 

 

 

 

 

 

 

Output holdup time

10 ms minimum

 

 

 

 

 

 

 

 

 

 

 

Front panel LEDs

 

 

 

 

 

 

INPUT OK

 

Green—Source AC voltage is OK. (Input voltage is 82 VAC or

 

 

 

 

 

 

greater.)

 

 

 

 

 

 

Red—Source AC voltage is less than 73 VAC (±3 VAC)

 

 

 

 

 

 

Off—Source AC voltage falls below 70 VAC, is not present, or the

 

 

 

 

 

 

power supply is turned off.

 

 

 

 

 

 

Note In chassis equipped with dual power supplies, if one power

 

 

 

 

 

 

supply is powered on and the other power supply is powered off,

 

 

 

 

 

 

the INPUT OK LED is lit red rather than unlit on the power

 

 

 

 

 

 

supply that is powered off.

 

 

 

 

FAN OK

 

Green—Power supply fan is operating properly.

 

 

 

 

 

 

Red—Power supply fan failure is detected.

 

 

 

 

 

 

Off—Power supply is powered off.

 

 

 

 

 

 

Note In chassis equipped with dual power supplies, if one power

 

 

 

 

 

 

supply is powered on and the other power supply is powered off,

 

 

 

 

 

 

the FAN OK LED is lit red rather than unlit on the power supply

 

 

 

 

 

 

that is powered off.

 

 

 

 

OUTPUT OK

Green—The 12 VDC output is within margins.

 

 

 

 

 

 

Red—The 12 VDC output is out of tolerance (less than 11.15 VDC or

 

 

 

 

 

 

more than 13.10 VDC).

 

 

 

 

 

 

Off—The power supply is off.

 

 

 

 

 

 

Note In chassis equipped with dual power supplies, if one power

 

 

 

 

 

 

supply is powered on and the other power supply is powered off,

 

 

 

 

 

 

the OUTPUT OK LED is lit red rather than unlit on the power

 

 

 

 

 

 

supply that is powered off.

 

 

 

 

 

 

 

 

 

 

 

Weight

 

4.41 lb (2 kg)

 

 

 

 

 

 

 

 

 

Cisco ME 6500 Series Ethernet Switch Installation Guide

 

 

 

 

 

 

 

 

 

 

 

 

A-4

 

 

 

 

OL-8900-03

 

 

 

 

 

 

 

Image 74
Contents Cisco ME 6500 Series Ethernet Switch Installation Guide Americas HeadquartersPage N T E N T S Where to Go Next Power Supply Specifications OL-8900-03 Chapter Title Description AudienceOrganization Conventions Convention DescriptionStatement 1071-Warning Definition Bewaar Deze InstructiesAviso Instruções Importantes DE Segurança Warnung Wichtige SicherheitshinweiseAvvertenza Importanti Istruzioni Sulla Sicurezza Spara Dessa Anvisningar GEM Disse Anvisninger Xiii Related Documentation Obtaining Documentation and Submitting a Service Request Xvi Cisco ME 6524 Ethernet Switch ME-C6524GS-8S Product OverviewFeature Cisco ME 6524 Ethernet Switch ME-C6524GS-8S-Rear ViewFeature Description Status LED Specification Operational-5 G 30 ms, half-sine IEC Cisco ME 6524 Ethernet Switch ME-C6524GT-8S Cisco ME 6524 Ethernet Switch ME-C6524GT-8S-Front ViewCisco ME 6524 Ethernet Switch ME-C6524GT-8S-Rear View Cisco ME 6524 Ethernet Switch ME-C6524GT-8S Features Status LED Cisco ME 6524 Ethernet Switch ME-C6524GT-8S Specifications Operational-5 G 30 ms, half-sine IEC Preparing for Installation SafetyPreparing for Installation Safety Temperature and Air Circulation Site RequirementsHumidity AltitudeElectromagnetic and Radio Frequency Interference Dust and ContaminationCorrosion Electromagnetic Environment Shock and VibrationSystem Grounding Grounding RecommendationsPreventing Electrostatic Discharge Damage Preparing for Installation Site Requirements Power Requirements Power Connection Guidelines for AC-Powered Systems Power Connection Guidelines for DC-Powered SystemsSite Preparation Checklist Cabling RequirementsTask No. Planning Activity Verified By Time Installing the Switch Preparing for InstallationOL-8900-03 Installing the Switch Preparing for Installation Required Tools Verifying Package ContentsRack-Mounting Installing the Rack-Mount Brackets Attaching L Brackets to the ChassisInstalling the Chassis in the Rack Installing the Chassis in the Rack Desk-Top MountingInstalling the System Ground Installing the Rubber FeetConnecting Source Power to the Chassis Installing the System GroundConnecting Source DC to the DC-Input Power Supply Connecting the Console Port Connecting Source AC to the AC-Input Power SupplyInstalling the SFP Transceivers Receive optical bore Transmit optical bore Bail claspInstalling an SFP Transceiver into an SFP Transceiver Socket Installing the Switch Installing the SFP Transceivers Powering Up the Chassis Where to Go NextOL-8900-03 Removal and Replacement Procedures Removing and Installing the DC-Input Power SupplyRemoving the DC-Input Power Supply Removing the DC-Input Power Supply Installing the DC-Input Power Supply Page Removing and Installing the AC-Input Power Supply Installing the DC-Input Power SupplyRemoving the AC-Input Power Supply IEC 60320 C15 connectorRemoving and Installing the Fan Tray Installing the AC-Input Power SupplyInstalling the Fan Tray Removing the Fan TrayUpgrading the Memory Location of SP and RP Dram DIMMs Connector edge of the Dimm into the socket connector Installing the Dram Dimm in the Dimm Socket OL-8900-03 Power Supply Specifications DC-Input Power SupplyFAN OK AC-Input Power Supply Specification DescriptionGreen-Source AC voltage is OK. Input voltage is 82 VAC or Power Supply AC Power Cords Locale Power CordFigure A-4 CAB-ACA Australia and New Zealand Power Cord Figure A-7 CAB-ACE Continental Europe Power Cord Figure A-10 CAB-ACU United Kingdom Power Cord SFP Transceiver Specifications Core Size Bandwidth ModalSFP Transceiver Type Fiber Type Micron MHz/km Cable DistanceMB SFP Transceiver Transmit dBm Receive dBm Product Number GB SFP Transceiver Transmit dBm Receive dBm Product NumberColor Code Cwdm Gbic Wavelength Dwdm SFP Description ITU Channel Product NumberDwdm SFP Numerics IN-2 IN-3 IN-4
Related manuals
Manual 14 pages 28.35 Kb

ME 6500 specifications

The Cisco Systems ME 6500 is a sophisticated Ethernet switch designed to cater to the demanding needs of service providers and large enterprises. Engineered to deliver high performance and reliability, the ME 6500 series is ideal for both metro Ethernet applications and data center environments. One of its standout features is the ability to handle massive bandwidth, making it suitable for high-capacity networks. The switch supports a range of Ethernet services that facilitate seamless connectivity and network expansion.

At the core of the ME 6500 is its ability to provide Layer 2 and Layer 3 functionalities, which allows for flexibility in network design. This dual-layer capability enhances the switch's efficiency in managing traffic and ensures optimal forwarding of data packets. In addition, the ME 6500 series supports a wide range of Ethernet interfaces, including 10 Gigabit and 1 Gigabit Ethernet ports, which are essential for accommodating diverse bandwidth requirements.

One of the defining characteristics of the Cisco ME 6500 is its scalability. It supports up to 192 10 Gigabit Ethernet ports within a single chassis, enabling organizations to expand their network without compromising performance. Furthermore, the switch includes advanced Quality of Service (QoS) features that allow for traffic prioritization, which is crucial for maintaining the performance of voice and video services across the network.

The ME 6500 switch is also equipped with robust security features, including Access Control Lists (ACLs) and secure management protocols. These features protect sensitive data as it traverses the network, ensuring that only authorized users have access to critical resources. Management of the switch is simplified through Cisco’s management tools, allowing network administrators to monitor, configure, and troubleshoot the device efficiently.

Additionally, the switch supports various redundancy protocols, including Rapid Spanning Tree Protocol (RSTP) and Link Aggregation Control Protocol (LACP), ensuring high availability and minimizing downtime.

Overall, the Cisco ME 6500 is a powerful and versatile solution that meets the heavy demands of modern network environments, delivering outstanding performance, security, and scalability for both service providers and large enterprises. Its advanced features make it a go-to choice for organizations looking to future-proof their networking infrastructure.