Cisco Systems 2940 manual Preparing for Installation

Page 31

C H A P T E R 2

Installation

This chapter describes how to install your switch, how to interpret the power-on self-test (POST), and how to connect the switch to other devices. Read these topics, and perform the procedures in this order:

•Preparing for Installation, page 2-1

•Verifying Switch Operation, page 2-4

•Installing the Switch, page 2-5

•Connecting to an SFP Module, page 2-12

•Connecting to 10/100 Ports and the 10/100/1000 Port, page 2-14

•Connecting to the 100BASE-FX Port, page 2-15

•Connecting to an SFP Module, page 2-16

•Where to Go Next, page 2-17

Preparing for Installation

This section provides information about these topics:

•Warnings, page 2-1

•Installation Guidelines, page 2-3

•Verifying Package Contents, page 2-3

Warnings

These warnings are translated into several languages in the Regulatory Compliance and Safety Information for the Catalyst 2940 Switch.

Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030

Warning Read the installation instructions before connecting the system to the power source. Statement 1004

Catalyst 2940 Switch Hardware Installation Guide

	OL-6157-01	2-1

Image 31

Contents Corporate Headquarters Catalyst 2940 Switch Hardware Installation GuideCatalyst 2940 Switch Hardware Installation Guide N T E N T S Installation Accessing the CLI Through the Console Port D-2 Contents Catalyst 2940 Hardware Installation Guide Purpose AudienceConventions Warnung Wichtige Sicherheitshinweise Bewaar Deze InstructiesAviso Instruções Importantes DE Segurança Avvertenza Importanti Istruzioni Sulla SicurezzaOL-6157-01 GEM Disse Anvisninger Xii Related Publications Ordering Documentation Obtaining DocumentationCisco.com Documentation CD-ROMDocumentation Feedback Obtaining Technical AssistanceCisco TAC Website Opening a TAC Case TAC Case Priority Definitions Obtaining Additional Publications and InformationXvii Xviii Features Setting up the Switch10/100 Ethernet ports 100BASE-FX port SFP module slot Front-Panel DescriptionPort or Slot type Catalyst 2940-8TT-S Catalyst 2940-8TF-S Port Numbering10/100 Ports 10/100/1000 PortSFP Module Slot 100BASE-FX PortType Cisco Part Number Micron SFP Modules62.5/125 micron 50/125 micron Micron Single-mode LEDs Cable GuardColor System Status Mode LED Port Mode DescriptionPort Mode Color Meaning Rear-Panel Description Power ConnectorSecurity Slots Console PortManagement Options OL-6157-01 Preparing for Installation InstallationChapter Verifying Package Contents Installation GuidelinesVerifying Switch Operation Installing the Switch on a Desk Without Mounting Screws Installing the SwitchInstalling the Switch on a Desk With Mounting Screws Installing the Mounting Screws on Top of a Desk Mounting the Switch on Top of a Desk Installing the Switch Under a DeskInstalling the Mounting Screws Under a Desk Mounting the Switch Under a Desk Installing the Switch on a WallThis Side Switch Screw Slides on this way Installing the Switch Magnet Mount Connecting to an SFP ModuleConnecting to an SFP Module Port Connecting to a 10/100 Port Connecting to 10/100 Ports and the 10/100/1000 Port10 Connecting to a 100BASE-FX Port Connecting to the 100BASE-FX Port11 Connecting to an SFP Module Port Where to Go Next Chapter Understanding Post Results Diagnosing Common ProblemsB-5 through Symptom Possible Cause ResolutionNo connectivity to SFP Poor performance or excessive System LED is amber OL-6157-01 Physical Dimensions Power RequirementsEnvironmental Ranges Safety Fiber-Port Power Levels 100BASE-FX port Slot1SFP module Table A-3 Catalyst 2940 Switch Agency Approvals OL-6157-01 Connector Specifications Connectors and CablesFigure B-2 10/100 RJ-45 Pinouts 10/100/1000 Ports Connecting to 10BASE-T and 100BASE-TX DevicesFigure B-4 MT-RJ Connector Two Twisted-Pair Cable Pinouts Cable and Adapter SpecificationsTD+ Four Twisted-Pair Cable Pinouts for 10/100 PortsTPO Four Twisted-Pair Cable Pinouts for 1000BASE-T PortsCable and Adapter Pinouts Connecting to a PCIdentifying a Rollover Cable OL-6157-01 Methods for Accessing the CLI Configuring the Switch with the CLI-Based Setup ProgramTaking Out What You Need Accessing the CLI Through the Console PortConnecting to the Console Port Connecting to a Power SourceStarting the Terminal Emulation Software Figure C-3 Connecting a Switch to a PCIP Settings Entering the Initial Configuration InformationCompleting the Setup Program These choices appear CLI Numerics IN-2 IN-3 IN-4 IN-5 IN-6

Related manuals

Manual 12 pages 57.66 Kb

Manual 12 pages 30.15 Kb