Cisco Systems manual Table A-3 Catalyst 2940 Switch Agency Approvals

Page 57

Appendix A Technical Specifications

Table A-3 Catalyst 2940 Switch Agency Approvals (continued)

EN61000-4-11/IEC1000-4-11: Immunity to Voltage

Dips, Voltage Variations, and Short Voltage

Interruptions

AS/NZS 3548, Class A

BSMI, Class A

VCCI, Class A

MIC Mark

Catalyst 2940 Switch Hardware Installation Guide

	OL-6157-01	A-3

Image 57

Contents Corporate Headquarters Catalyst 2940 Switch Hardware Installation GuideCatalyst 2940 Switch Hardware Installation Guide N T E N T S Installation Accessing the CLI Through the Console Port D-2 Contents Catalyst 2940 Hardware Installation Guide Audience PurposeConventions Warnung Wichtige Sicherheitshinweise Bewaar Deze InstructiesAviso Instruções Importantes DE Segurança Avvertenza Importanti Istruzioni Sulla SicurezzaOL-6157-01 GEM Disse Anvisninger Xii Related Publications Cisco.com Obtaining DocumentationDocumentation CD-ROM Ordering DocumentationObtaining Technical Assistance Documentation FeedbackCisco TAC Website Opening a TAC Case TAC Case Priority Definitions Obtaining Additional Publications and InformationXvii Xviii Features Setting up the Switch10/100 Ethernet ports 100BASE-FX port SFP module slot Front-Panel Description10/100 Ports Port Numbering10/100/1000 Port Port or Slot type Catalyst 2940-8TT-S Catalyst 2940-8TF-S100BASE-FX Port SFP Module SlotType Cisco Part Number SFP Modules Micron62.5/125 micron 50/125 micron Micron Single-mode LEDs Cable GuardColor System Status Mode LED Port Mode DescriptionPort Mode Color Meaning Rear-Panel Description Power ConnectorSecurity Slots Console PortManagement Options OL-6157-01 Preparing for Installation InstallationChapter Verifying Package Contents Installation GuidelinesVerifying Switch Operation Installing the Switch Installing the Switch on a Desk Without Mounting ScrewsInstalling the Switch on a Desk With Mounting Screws Installing the Mounting Screws on Top of a Desk Mounting the Switch on Top of a Desk Installing the Switch Under a DeskInstalling the Mounting Screws Under a Desk Mounting the Switch Under a Desk Installing the Switch on a WallThis Side Switch Screw Slides on this way Installing the Switch Magnet Mount Connecting to an SFP ModuleConnecting to an SFP Module Port Connecting to a 10/100 Port Connecting to 10/100 Ports and the 10/100/1000 Port10 Connecting to a 100BASE-FX Port Connecting to the 100BASE-FX Port11 Connecting to an SFP Module Port Where to Go Next Chapter Understanding Post Results Diagnosing Common ProblemsB-5 through Symptom Possible Cause ResolutionNo connectivity to SFP Poor performance or excessive System LED is amber OL-6157-01 Power Requirements Physical DimensionsEnvironmental Ranges Fiber-Port Power Levels 100BASE-FX port Slot1 SafetySFP module Table A-3 Catalyst 2940 Switch Agency Approvals OL-6157-01 Connector Specifications Connectors and CablesFigure B-2 10/100 RJ-45 Pinouts 10/100/1000 Ports Connecting to 10BASE-T and 100BASE-TX DevicesFigure B-4 MT-RJ Connector Two Twisted-Pair Cable Pinouts Cable and Adapter SpecificationsTD+ Four Twisted-Pair Cable Pinouts for 10/100 PortsTPO Four Twisted-Pair Cable Pinouts for 1000BASE-T PortsCable and Adapter Pinouts Connecting to a PCIdentifying a Rollover Cable OL-6157-01 Methods for Accessing the CLI Configuring the Switch with the CLI-Based Setup ProgramTaking Out What You Need Accessing the CLI Through the Console PortConnecting to the Console Port Connecting to a Power SourceStarting the Terminal Emulation Software Figure C-3 Connecting a Switch to a PCIP Settings Entering the Initial Configuration InformationCompleting the Setup Program These choices appear CLI Numerics IN-2 IN-3 IN-4 IN-5 IN-6

Related manuals

Manual 12 pages 57.66 Kb

Manual 12 pages 30.15 Kb