Cisco Systems PA-T3 manual FCC Class a Compliance, Preventing Electrostatic Discharge Damage

Page 18

FCC Class A Compliance

Preventing Electrostatic Discharge Damage

Electrostatic discharge (ESD) damage, which can occur when electronic cards or components are improperly handled, results in complete or intermittent failures. Port adapters and processor modules consist of printed circuit boards that are fixed in metal carriers. Electromagnetic interference (EMI) shielding and connectors are integral components of the carrier. Although the metal carrier helps to protect the board from ESD, use a preventive antistatic strap during handling.

Following are guidelines for preventing ESD damage:

•Always use an ESD wrist or ankle strap and ensure that it makes good skin contact.

•Connect the equipment end of the strap to an unfinished chassis surface.

•When installing a component, use any available ejector levers or captive installation screws to properly seat the bus connectors in the backplane or midplane. These devices prevent accidental removal, provide proper grounding for the system, and help to ensure that bus connectors are properly seated.

•When removing a component, use any available ejector levers or captive installation screws to release the bus connectors from the backplane or midplane.

•Handle carriers by available handles or edges only; avoid touching the printed circuit boards or connectors.

•Place a removed board component-side-up on an antistatic surface or in a static shielding container. If you plan to return the component to the factory, immediately place it in a static shielding container.

•Avoid contact between the printed circuit boards and clothing. The wrist strap only protects components from ESD voltages on the body; ESD voltages on clothing can still cause damage.

•Never attempt to remove the printed circuit board from the metal carrier.

Caution For safety, periodically check the resistance value of the antistatic strap. The measurement should be between 1 and 10 megohms (Mohm).

FCC Class A Compliance

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.

You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:

•

•

•

Turn the television or radio antenna until the interference stops.

Move the equipment to one side or the other of the television or radio.

Move the equipment farther away from the television or radio.

2-8PA-T3 Serial Port Adapter Installation and Configuration

Page 17 Page 19
Image 18
Page 17 Page 19
Contents PA-T3 Serial Port Adapter Installation and Configuration Corporate HeadquartersPage Organization PrefaceObjectives Section Title DescriptionRelated Documentation Related Documentation Section Title DescriptionCisco Connection Online Cisco Connection OnlineCisco Documentation CD-ROM Cisco Documentation CD-ROMOverview Port Adapter OverviewPA-T3 Serial Port Adapter Features PA-T3 Serial Port Adapter FeaturesManagement Information Base Management Information Base4PA-T3 Serial Port Adapter Installation and Configuration Preparing for Installation Parts and Tools RequiredSoftware and Hardware Requirements Software and Hardware RequirementsPA-2T3 PA-T3 Port Adapter LEDs PA-T3 Port Adapter LEDsRouter show version LEDs for Uplink Port Status Color State DescriptionPA-T3 Receptacles and Cables Feature Compatibilities of PA-T3 Serial Port Adapter DSUsPA-T3 Receptacles and Cables Full Rate Scrambling Subrate MDL 1 SupportSafety Guidelines Safety GuidelinesTelephone Wiring Guidelines Electrical Equipment GuidelinesElectrical Equipment Guidelines FCC Class a Compliance Preventing Electrostatic Discharge DamageFCC Class a Compliance FCC Class a Compliance 10PA-T3 Serial Port Adapter Installation and Configuration VIP2 and the PA-T3 Port Adapter OverviewOverview Dimm U5PA-T3 in port adapter Slot PA-T3 in port adapter slot Removing a Port Adapter Removing a Port AdapterInstalling a Port Adapter Installing a Port AdapterH3152 Installing a Port Adapter 8PA-T3 Serial Port Adapter Installation and Configuration Catalyst RSM/VIP2 and the PA-T3 Port Adapter Standoff Removing a Port Adapter Installing a Port Adapter Aligning a Port Adapter in a Port Adapter Slot 6PA-T3 Serial Port Adapter Installation and Configuration Cisco 7200 Series PA-T3 Port Adapter Port adapter Handle Lever unlocked Position Handling a Port Adapter Port adapter Handle Cisco uBR7200 Series and the PA-T3 Port Adapter Port adapters Port adapters Port adapter lever in unlocked position Inside slot guide PC board Metal carrier Port adapter retention clip in locked position 6PA-T3 Serial Port Adapter Installation and Configuration Configuring the PA-T3 Interfaces Identifying Port Adapter Slot and T3 Interface Port Numbers Using the Exec Command InterpreterUsing the Exec Command Interpreter Cisco 7200 Series and Cisco uBR7200 Series PortsCisco 7200 Series and Cisco uBR7200 Series Ports Serial Port Number Example-CiscoVIP2 Ports Identifying Port Adapter Slot and T3 Interface Port NumbersCatalyst RSM/VIP2 Ports Catalyst RSM/VIP2 PortsCisco 7100 Series Ports PA-T3 Serial Port Adapter in the CatalystShutting Down an Interface Interface Subcommand Syntax Platform Command ExampleRouter# configure terminal Shutting Down an InterfaceRouterconfig-if#interface serial 1/1/0 Routerconfig-if#interface serial 1/0Routerconfig-if#interface serial 1/1 Routerconfig-if#interface serial 1/1/1Router# show interfaces serial 1/0 Routerconfig# interface serial 1/0Router# copy running-config startup-config OK Router# show interfaces serial 1/1/0Routerconfig# interface serial 3/0 Performing a Basic ConfigurationRouterconfig# interface serial 1/1/0 Performing a Basic ConfigurationConfiguration Example Configuration ExampleCustomizing the PA-T3 Serial Port Adapter Setting the BandwidthDefining the DSU Mode Enabling T3 ScramblingSpecifying T3 Framing Setting the Cable LengthConfiguring Cyclic Redundancy Checks Specifying T3 FramingUsing show Commands to Verify Status Checking the ConfigurationChecking the Configuration Show running-config command. Display Router# show interfaces serial 2/0 Router# show controllers 2/0 Router# show controllers serial 3/0Febe Router# show controllers serial 10/0/0 Serial10/0/0Router# show controllers serial 0/0 Serial0/0 Router# show version20PA-T3 Serial Port Adapter Installation and Configuration Router# show diag Router# show controllers cbus 1/0/0 Router# show controllers cbus 0/0 Using the ping Command to Verify Network Connection Using the loopback Command to Verify the Physical InterfaceRouterconfig# interface serial 6/0 Set the interface into local loopback mode as follows Using the loopback Command to Verify the Physical Interface26PA-T3 Serial Port Adapter Installation and Configuration Cisco 7100 Series and the PA-T3 Port Adapter Cisco 7120 Series Router-Port Adapter Slot 3 LocationCisco 7140 Series Router-Port Adapter Slot 4 Location Installing a Port Adapter Guides
Top Page Image Contents