Cisco Systems PA-T3 manual Standoff

Page 30

Overview

Figure 4-1 Catalyst RSM/VIP2-15 or Catalyst RSM/VIP2-40 with One-Port PA-T3 Serial Port Adapters in Port Adapter Slots 0 and 1

 

Standoff

 

 

mounting

Ribbon cables

Backplane

hole

 

 

 

bus connector

 

 

Standoff

 

Standoff

 

mounting

mounting

 

 

holes

holes

 

 

 

PA-T3 in port adapter slot 0

ENABLED

RCVR XMTR

 

RCLK FERF RL

 

 

AIS OOF

LL

 

 

 

Port adapter handles not shown

DS3 SERIAL

ENABLED

RCVR XMTR

 

RCLK FERF RL

AIS OOF

LL

 

PA-T3 in port adapter slot 1

DS3 SERIAL

25704

Note Port adapters have a handle attached, but this handle is not shown to allow a full view of detail on each port adapter’s faceplate.

Depending on the circumstances, you might need to install a new port adapter on a

Catalyst RSM/VIP2 motherboard or replace a failed port adapter in the field. In either case, you need a number 1 Phillips screwdriver, an antistatic mat on which you can place the removed interface processor, and an antistatic container in which you can place a failed port adapter for shipment back to the factory.

Caution To prevent system problems, do not remove port adapters from the Catalyst RSM/VIP2 motherboard or attempt to install other port adapters on the Catalyst RSM/VIP2 motherboard while the system is operating. To install or replace port adapters, first remove the Catalyst RSM/VIP2 from the chassis.

Note Each port adapter circuit board is mounted to a metal carrier and is sensitive to ESD damage. The following procedures should be performed by a Cisco-certified service provider only. The Catalyst RSM/VIP2 supports online insertion and removal (OIR), but individual port adapters do not. To replace port adapters, you must first remove the Catalyst RSM/VIP2 from the chassis and then install or replace port adapters as required. If a blank port adapter is installed on the Catalyst RSM/VIP2 in which you want to install a new port adapter, you must first remove the Catalyst RSM/VIP2 from the chassis and then remove the blank port adapter.

4-2PA-T3 Serial Port Adapter Installation and Configuration

Image 30
Contents PA-T3 Serial Port Adapter Installation and Configuration Corporate HeadquartersPage Organization PrefaceObjectives Section Title DescriptionRelated Documentation Related Documentation Section Title DescriptionCisco Connection Online Cisco Connection OnlineCisco Documentation CD-ROM Cisco Documentation CD-ROMOverview Port Adapter OverviewPA-T3 Serial Port Adapter Features PA-T3 Serial Port Adapter FeaturesManagement Information Base Management Information Base4PA-T3 Serial Port Adapter Installation and Configuration Preparing for Installation Parts and Tools RequiredSoftware and Hardware Requirements Software and Hardware RequirementsPA-2T3 PA-T3 Port Adapter LEDs PA-T3 Port Adapter LEDsRouter show version LEDs for Uplink Port Status Color State DescriptionPA-T3 Receptacles and Cables Feature Compatibilities of PA-T3 Serial Port Adapter DSUsPA-T3 Receptacles and Cables Full Rate Scrambling Subrate MDL 1 SupportSafety Guidelines Safety GuidelinesTelephone Wiring Guidelines Electrical Equipment GuidelinesElectrical Equipment Guidelines FCC Class a Compliance Preventing Electrostatic Discharge DamageFCC Class a Compliance FCC Class a Compliance 10PA-T3 Serial Port Adapter Installation and Configuration VIP2 and the PA-T3 Port Adapter OverviewOverview Dimm U5PA-T3 in port adapter Slot PA-T3 in port adapter slot Removing a Port Adapter Removing a Port AdapterInstalling a Port Adapter Installing a Port AdapterH3152 Installing a Port Adapter 8PA-T3 Serial Port Adapter Installation and Configuration Catalyst RSM/VIP2 and the PA-T3 Port Adapter Standoff Removing a Port Adapter Installing a Port Adapter Aligning a Port Adapter in a Port Adapter Slot 6PA-T3 Serial Port Adapter Installation and Configuration Cisco 7200 Series PA-T3 Port Adapter Port adapter Handle Lever unlocked Position Handling a Port Adapter Port adapter Handle Cisco uBR7200 Series and the PA-T3 Port Adapter Port adapters Port adapters Port adapter lever in unlocked position Inside slot guide PC board Metal carrier Port adapter retention clip in locked position 6PA-T3 Serial Port Adapter Installation and Configuration Configuring the PA-T3 Interfaces Identifying Port Adapter Slot and T3 Interface Port Numbers Using the Exec Command InterpreterUsing the Exec Command Interpreter Cisco 7200 Series and Cisco uBR7200 Series PortsCisco 7200 Series and Cisco uBR7200 Series Ports Serial Port Number Example-CiscoVIP2 Ports Identifying Port Adapter Slot and T3 Interface Port NumbersCatalyst RSM/VIP2 Ports Catalyst RSM/VIP2 PortsCisco 7100 Series Ports PA-T3 Serial Port Adapter in the CatalystShutting Down an Interface Interface Subcommand Syntax Platform Command ExampleRouter# configure terminal Shutting Down an InterfaceRouterconfig-if#interface serial 1/1/0 Routerconfig-if#interface serial 1/0Routerconfig-if#interface serial 1/1 Routerconfig-if#interface serial 1/1/1Router# show interfaces serial 1/0 Routerconfig# interface serial 1/0Router# copy running-config startup-config OK Router# show interfaces serial 1/1/0Routerconfig# interface serial 3/0 Performing a Basic ConfigurationRouterconfig# interface serial 1/1/0 Performing a Basic ConfigurationConfiguration Example Configuration ExampleCustomizing the PA-T3 Serial Port Adapter Setting the BandwidthDefining the DSU Mode Enabling T3 ScramblingSpecifying T3 Framing Setting the Cable LengthConfiguring Cyclic Redundancy Checks Specifying T3 FramingUsing show Commands to Verify Status Checking the ConfigurationChecking the Configuration Show running-config command. Display Router# show interfaces serial 2/0 Router# show controllers 2/0 Router# show controllers serial 3/0Febe Router# show controllers serial 10/0/0 Serial10/0/0Router# show controllers serial 0/0 Serial0/0 Router# show version20PA-T3 Serial Port Adapter Installation and Configuration Router# show diag Router# show controllers cbus 1/0/0 Router# show controllers cbus 0/0 Using the ping Command to Verify Network Connection Using the loopback Command to Verify the Physical InterfaceRouterconfig# interface serial 6/0 Set the interface into local loopback mode as follows Using the loopback Command to Verify the Physical Interface26PA-T3 Serial Port Adapter Installation and Configuration Cisco 7100 Series and the PA-T3 Port Adapter Cisco 7120 Series Router-Port Adapter Slot 3 LocationCisco 7140 Series Router-Port Adapter Slot 4 Location Installing a Port Adapter Guides