Cisco Systems PA-T3 manual Port adapter retention clip in locked position

Page 43

Installing a Port Adapter

Figure 6-6 Placing the Port Adapter Retention Clip in the Locked

Position—Cisco uBR7246 Shown

Port adapters

H11517

Port adapter retention clip in locked position

•For a Cisco uBR7223, place the port adapter lever in the locked position. (See Figure 6-7.)

Figure 6-7 Placing the Port Adapter Lever in the Locked

Position—Cisco uBR7223 Shown

Port adapters

Port adapter lever in locked position

16177

Note If the port adapter lever does not move to the locked position, the port adapter is not completely seated in the midplane. Carefully pull the port adapter halfway out of the slot, reinsert it, and move the port adapter lever to the locked position.

This completes the procedure for installing a port adapter in a Cisco uBR7200 series router. Proceed to Chapter 8, “Conﬁguring the PA-T3 Interfaces,” for information on how to conﬁgure your port adapter interfaces.

Cisco uBR7200 Series and the PA-T3 Port Adapter 6-5

Image 43

Contents Corporate Headquarters PA-T3 Serial Port Adapter Installation and ConfigurationPage Section Title Description PrefaceObjectives OrganizationRelated Documentation Section Title Description Related DocumentationCisco Connection Online Cisco Connection OnlineCisco Documentation CD-ROM Cisco Documentation CD-ROMPort Adapter Overview OverviewPA-T3 Serial Port Adapter Features PA-T3 Serial Port Adapter FeaturesManagement Information Base Management Information Base4PA-T3 Serial Port Adapter Installation and Configuration Parts and Tools Required Preparing for InstallationSoftware and Hardware Requirements Software and Hardware RequirementsPA-2T3 PA-T3 Port Adapter LEDs PA-T3 Port Adapter LEDsRouter show version Color State Description LEDs for Uplink Port StatusFull Rate Scrambling Subrate MDL 1 Support Feature Compatibilities of PA-T3 Serial Port Adapter DSUsPA-T3 Receptacles and Cables PA-T3 Receptacles and CablesSafety Guidelines Safety GuidelinesElectrical Equipment Guidelines Telephone Wiring GuidelinesElectrical Equipment Guidelines Preventing Electrostatic Discharge Damage FCC Class a ComplianceFCC Class a Compliance FCC Class a Compliance 10PA-T3 Serial Port Adapter Installation and Configuration Overview VIP2 and the PA-T3 Port AdapterDimm U5 OverviewPA-T3 in port adapter Slot PA-T3 in port adapter slot Removing a Port Adapter Removing a Port AdapterInstalling a Port Adapter Installing a Port AdapterH3152 Installing a Port Adapter 8PA-T3 Serial Port Adapter Installation and Configuration Catalyst RSM/VIP2 and the PA-T3 Port Adapter Standoff Removing a Port Adapter Installing a Port Adapter Aligning a Port Adapter in a Port Adapter Slot 6PA-T3 Serial Port Adapter Installation and Configuration Cisco 7200 Series PA-T3 Port Adapter Port adapter Handle Lever unlocked Position Handling a Port Adapter Port adapter Handle Cisco uBR7200 Series and the PA-T3 Port Adapter Port adapters Port adapters Port adapter lever in unlocked position Inside slot guide PC board Metal carrier Port adapter retention clip in locked position 6PA-T3 Serial Port Adapter Installation and Configuration Configuring the PA-T3 Interfaces Cisco 7200 Series and Cisco uBR7200 Series Ports Using the Exec Command InterpreterUsing the Exec Command Interpreter Identifying Port Adapter Slot and T3 Interface Port NumbersSerial Port Number Example-Cisco Cisco 7200 Series and Cisco uBR7200 Series PortsIdentifying Port Adapter Slot and T3 Interface Port Numbers VIP2 PortsCatalyst RSM/VIP2 Ports Catalyst RSM/VIP2 PortsPA-T3 Serial Port Adapter in the Catalyst Cisco 7100 Series PortsShutting Down an Interface Interface Subcommand Syntax Platform Command ExampleRouter# configure terminal Shutting Down an InterfaceRouterconfig-if#interface serial 1/1/1 Routerconfig-if#interface serial 1/0Routerconfig-if#interface serial 1/1 Routerconfig-if#interface serial 1/1/0Router# show interfaces serial 1/1/0 Routerconfig# interface serial 1/0Router# copy running-config startup-config OK Router# show interfaces serial 1/0Performing a Basic Conﬁguration Performing a Basic ConfigurationRouterconfig# interface serial 1/1/0 Routerconfig# interface serial 3/0Conﬁguration Example Configuration ExampleEnabling T3 Scrambling Setting the BandwidthDeﬁning the DSU Mode Customizing the PA-T3 Serial Port AdapterSpecifying T3 Framing Setting the Cable LengthConﬁguring Cyclic Redundancy Checks Specifying T3 FramingChecking the Configuration Using show Commands to Verify StatusChecking the Conﬁguration Show running-conﬁg command. Display Router# show interfaces serial 2/0 Router# show controllers serial 3/0 Router# show controllers 2/0Router# show controllers serial 10/0/0 Serial10/0/0 FebeRouter# show version Router# show controllers serial 0/0 Serial0/020PA-T3 Serial Port Adapter Installation and Configuration Router# show diag Router# show controllers cbus 1/0/0 Router# show controllers cbus 0/0 Using the loopback Command to Verify the Physical Interface Using the ping Command to Verify Network ConnectionRouterconfig# interface serial 6/0 Using the loopback Command to Verify the Physical Interface Set the interface into local loopback mode as follows26PA-T3 Serial Port Adapter Installation and Configuration Cisco 7120 Series Router-Port Adapter Slot 3 Location Cisco 7100 Series and the PA-T3 Port AdapterCisco 7140 Series Router-Port Adapter Slot 4 Location Installing a Port Adapter Guides