Cisco Systems CX-FEIP-2TX=, CX-FEIP-1TX=, CX-FEIP-1FX= manual Cisco 7513 Interface Processor End

Page 14

Installation Prerequisites

In the Cisco 7513 (see Figure 7), slots 0 through 5 and 8 through 12 are for interface processors including the FEIP.

Figure 7 Cisco 7513 (Interface Processor End)

Blower module

Cable-management bracket

Card cage and processor modules

Air intake vent

AC	FAN	OUTPUT
OK	OK	FAIL

Power supplies	POWER
	A
Chassis grounding	I
Chassis grounding
receptacles	0
receptacles

NORMAL
		ENABLE
EJECT
SLOT	1
SLOT0	1
SLAVEMASTER
SLAVE/MASTER
CPU	HALT
	HALT
RESET		ENABLE
		ENABLE
AUX.

	CONSOLE	ROUTE
	CONSOLE	SWITCHPROCESSOR2
		SWITCHPROCESSOR2

AC	FAN	OUTPUT
OK	OK	FAIL

POWER

B

I

0

H5268

14Fast Ethernet Interface Processor (FEIP) Installation and Conﬁguration

Image 14

Contents Corporate Headquarters Document Contents If You Need More InformationSoftware and Hardware Prerequisites Installation PrerequisitesInstallation Prerequisites Electrical Equipment Guidelines Safety GuidelinesList of Parts and Tools Preventing Electrostatic Discharge Damage Telephone Wiring GuidelinesSafety Guidelines Guidelines for Interface Processor Installation and Removal Guidelines for Interface Processor Installation and Removal Orientation ShownMicrocode Overview Fast Ethernet OverviewIeee 802.3u 100BaseT Speciﬁcations Ieee 802.3u 100BaseT Specifications100BASE-FX Multimode 100BASE-FX Single Mode ParameterWhat Is the Cisco 7000 Series? DTE DTEWhat Is the Cisco 7000 Series? Cisco 7000 Interface Processor EndWhat Is the Cisco 7500 Series? Cisco 7505 Interface Processor EndWhat Is the Cisco 7500 Series? Cisco 7507 Interface Processor EndCisco 7513 Interface Processor End Fast Ethernet Interface Processor FEIP-2TX What Is the FEIP?What Is the FEIP? Feip LEDs LEDs on an Feip Port Adapter Partial Faceplate View1FE-TX Port Adapter Faceplate View Feip Receptacles, Cables, and PinoutsFeip Receptacles, Cables, and Pinouts 1FE-FX Port Adapter Faceplate ViewRJ-45 Connector Pinout Pin Description1FE-FX Duplex SC Connector MII Connector Pinout Pin Out In/Out DescriptionFeip Installation Feip InstallationRemoving an Feip Installing an Feip Installing an FeipAttaching Fast Ethernet Interface Cables Attaching Fast Ethernet Interface Cables Attaching the Ferrite Bead around the RJ-45 Cable Using LEDs to Check Feip Status Using LEDs to Check Feip StatusConﬁguring the Fast Ethernet Interfaces Conﬁguring the Fast Ethernet InterfacesSlot Interface Routerconfig-int#ip address 1.1.1.10 Router# configure terminalRouterconfig# interface fa 1/0/0 Router# copy running-config startup-configRouter# sh int fa 3/0/0 Configuring Interfaces-Descriptions and ExamplesRouterconfig# interface fastethernet 3/0/0 Step Using show Commands to Verify the Feip StatusChecking the Conﬁguration Router# sh int fastethernet 2/0/0 Using show Commands to Display Interface InformationChecking the Configuration Router# show interfaces fastethernet 2/0/0Router# show controllers cbus System image file is biff/rsp-jv-mz, booted via tftp from Router# show versionRouter# show diag Slot database informationUpgrading Feip Microcode Using the ping Command to Verify Network ConnectivityUpgrading Feip Microcode Router# show flash Router# copy tftpvip11-1 slot0vip11-1Routerconfig# microcode vip2 flash slot0vip11-1 To exit conﬁguration mode, press Ctrl-ZDocumentation CD-ROM Obtaining DocumentationWorld Wide Web Ordering DocumentationCisco.com Contacting TAC by Using the Cisco TAC WebsiteObtaining Technical Assistance Technical Assistance CenterObtaining Technical Assistance