Cisco Systems CX-FEIP-2TX=, CX-FEIP-1TX=, CX-FEIP-1FX=, CX-FEIP-2FX= Router# show controllers cbus

Page 34

Conﬁguring the Fast Ethernet Interfaces*

The show controllers cbus command displays information about all of the interface processors in your router, including the FEIP. Following is an example of the show controllers cbus command used with a Cisco 7500 series system:

Router# show controllers cbus

MEMD at 40000000, 2097152 bytes (unused 8256, recarves 1, lost 0) RawQ 48000100, ReturnQ 48000108, EventQ 48000110

BufhdrQ 48000128 (2357 items), LovltrQ 48000148 (6 items, 1632 bytes) IpcbufQ 48000158 (16 items, 4096 bytes)

IpcbufQ_classic 48000150 (8 items, 4096 bytes)

3570 buffer headers (48002000 - 4800FF10) pool0: 11 buffers, 256 bytes, queue 48000130 pool1: 1168 buffers, 1536 bytes, queue 48000138** pool2: 4 buffers, 1568 bytes, queue 48000140

(additional displayed text omitted from this example)

slot2: FEIP, hw 2.4, sw 21.40, ccb 5800FF40, cmdq 48000090, vps 8192 software loaded from system

IOS (tm) VIP Software (SVIP-DW-M), Released Version 11.1(10)CA [biff 138] ROM Monitor version 17.0

FastEthernet2/0/0, addr 0003.0b33.f540 (bia 0003.0b33.f540) gfreeq 48000138, lfreeq 480001C0 (1536 bytes), throttled 0 rxlo 4, rxhi 438, rxcurr 0, maxrxcurr 2

txq 48001A00, txacc 48001A02 (value 259), txlimit 259 FastEthernet2/1/0, addr 0003.0b33.f548 (bia 0003.0b33.f548)

gfreeq 48000138, lfreeq 480001C8 (1536 bytes), throttled 0 rxlo 4, rxhi 438, rxcurr 0, maxrxcurr 0

txq 48001A08, txacc 48001A0A (value 0), txlimit 259

(additional displayed text omitted from this example)

34Fast Ethernet Interface Processor (FEIP) Installation and Conﬁguration

Image 34

Contents Corporate Headquarters Document Contents If You Need More InformationInstallation Prerequisites Installation PrerequisitesSoftware and Hardware Prerequisites List of Parts and Tools Safety GuidelinesElectrical Equipment Guidelines Safety Guidelines Telephone Wiring GuidelinesPreventing Electrostatic Discharge Damage Guidelines for Interface Processor Installation and Removal Guidelines for Interface Processor Installation and Removal Orientation ShownMicrocode Overview Fast Ethernet OverviewIeee 802.3u 100BaseT Speciﬁcations Ieee 802.3u 100BaseT Specifications100BASE-FX Multimode 100BASE-FX Single Mode ParameterWhat Is the Cisco 7000 Series? DTE DTEWhat Is the Cisco 7000 Series? Cisco 7000 Interface Processor EndWhat Is the Cisco 7500 Series? Cisco 7505 Interface Processor EndWhat Is the Cisco 7500 Series? Cisco 7507 Interface Processor EndCisco 7513 Interface Processor End What Is the FEIP? What Is the FEIP?Fast Ethernet Interface Processor FEIP-2TX Feip LEDs LEDs on an Feip Port Adapter Partial Faceplate View1FE-TX Port Adapter Faceplate View Feip Receptacles, Cables, and PinoutsFeip Receptacles, Cables, and Pinouts 1FE-FX Port Adapter Faceplate ViewRJ-45 Connector Pinout Pin Description1FE-FX Duplex SC Connector MII Connector Pinout Pin Out In/Out DescriptionFeip Installation Feip InstallationRemoving an Feip Installing an Feip Installing an FeipAttaching Fast Ethernet Interface Cables Attaching Fast Ethernet Interface Cables Attaching the Ferrite Bead around the RJ-45 Cable Using LEDs to Check Feip Status Using LEDs to Check Feip StatusConﬁguring the Fast Ethernet Interfaces Conﬁguring the Fast Ethernet InterfacesSlot Interface Routerconfig-int#ip address 1.1.1.10 Router# configure terminalRouterconfig# interface fa 1/0/0 Router# copy running-config startup-configRouterconfig# interface fastethernet 3/0/0 Configuring Interfaces-Descriptions and ExamplesRouter# sh int fa 3/0/0 Checking the Conﬁguration Using show Commands to Verify the Feip StatusStep Router# sh int fastethernet 2/0/0 Using show Commands to Display Interface InformationChecking the Configuration Router# show interfaces fastethernet 2/0/0Router# show controllers cbus System image file is biff/rsp-jv-mz, booted via tftp from Router# show versionRouter# show diag Slot database informationUpgrading Feip Microcode Using the ping Command to Verify Network ConnectivityUpgrading Feip Microcode Router# show flash Router# copy tftpvip11-1 slot0vip11-1Routerconfig# microcode vip2 flash slot0vip11-1 To exit conﬁguration mode, press Ctrl-ZDocumentation CD-ROM Obtaining DocumentationWorld Wide Web Ordering DocumentationCisco.com Contacting TAC by Using the Cisco TAC WebsiteObtaining Technical Assistance Technical Assistance CenterObtaining Technical Assistance