Cisco Systems CX-FEIP-1TX=, CX-FEIP-1FX= manual Router# show diag, Slot database information

Page 36

Conﬁguring the Fast Ethernet Interfaces*

To determine which type of interfaces are installed on an FEIP in your system, use the

show diag slot command. Speciﬁc interface information is displayed, as shown in the following example of an FEIP in interface processor slot 2:

Router# show diag 2

Slot 2:

Physical slot 2, ~physical slot 0xD, logical slot 2, CBus 0

Microcode Status 0x4
Master Enable, LED, WCS Loaded
Board is analyzed
Pending	I/O Status: None
EEPROM format version 1
FEIP controller, HW rev 2.4, board revision D0
Serial number: 03700746					Part number: 73-1684-03
Test history: 0x00					RMA number: 00-00-00
Flags: cisco 7000 board; 7500 compatible
EEPROM contents (hex):
0x20:	01	20	02 04	00	38 78 0A 49	06	94 03 00 00	00	00
0x30:	68	00	00 03	00	00 00 00 00	00	00 00 00 00	00	00
Slot database information:
Flags: 0x4			Insertion time: 0x9B8 (00:17:10 ago)
Controller Memory Size: 8 MBytes DRAM, 1024 KBytes SRAM
PA Bay 0 Information:
	Fast-Ethernet PA, 1 ports, 100BaseTX-ISL
	EEPROM format version 1\
	HW rev 1.0, Board revision A0
	Serial number: 04622911					Part number: 73-1688-03
PA Bay 1 Information:
	Fast-Ethernet PA, 1 ports, 100BaseTX-ISL
	EEPROM format version 1
	HW rev 1.0, Board revision A0
	Serial number: 03540609					Part number: 73-1688-03

In the preceding example, the two interfaces on the FEIP are clearly marked 100BaseTX.

For additional Fast Ethernet command descriptions and examples, refer to the publications listed in the section “If You Need More Information” on page 2.

36Fast Ethernet Interface Processor (FEIP) Installation and Conﬁguration

Image 36

Contents Corporate Headquarters Document Contents If You Need More InformationInstallation Prerequisites Installation PrerequisitesSoftware and Hardware Prerequisites Safety Guidelines List of Parts and ToolsElectrical Equipment Guidelines Telephone Wiring Guidelines Safety GuidelinesPreventing Electrostatic Discharge Damage Guidelines for Interface Processor Installation and Removal Guidelines for Interface Processor Installation and Removal Orientation ShownMicrocode Overview Fast Ethernet OverviewIeee 802.3u 100BaseT Specifications 100BASE-FX Multimode 100BASE-FX Single ModeIeee 802.3u 100BaseT Speciﬁcations ParameterWhat Is the Cisco 7000 Series? DTE DTEWhat Is the Cisco 7000 Series? Cisco 7000 Interface Processor EndWhat Is the Cisco 7500 Series? Cisco 7505 Interface Processor EndWhat Is the Cisco 7500 Series? Cisco 7507 Interface Processor EndCisco 7513 Interface Processor End What Is the FEIP? What Is the FEIP?Fast Ethernet Interface Processor FEIP-2TX Feip LEDs LEDs on an Feip Port Adapter Partial Faceplate ViewFeip Receptacles, Cables, and Pinouts Feip Receptacles, Cables, and Pinouts1FE-TX Port Adapter Faceplate View 1FE-FX Port Adapter Faceplate ViewRJ-45 Connector Pinout Pin Description1FE-FX Duplex SC Connector MII Connector Pinout Pin Out In/Out DescriptionFeip Installation Feip InstallationRemoving an Feip Installing an Feip Installing an FeipAttaching Fast Ethernet Interface Cables Attaching Fast Ethernet Interface Cables Attaching the Ferrite Bead around the RJ-45 Cable Using LEDs to Check Feip Status Using LEDs to Check Feip StatusConﬁguring the Fast Ethernet Interfaces Conﬁguring the Fast Ethernet InterfacesSlot Interface Router# configure terminal Routerconfig# interface fa 1/0/0Routerconfig-int#ip address 1.1.1.10 Router# copy running-config startup-configConfiguring Interfaces-Descriptions and Examples Routerconfig# interface fastethernet 3/0/0Router# sh int fa 3/0/0 Using show Commands to Verify the Feip Status Checking the ConﬁgurationStep Using show Commands to Display Interface Information Checking the ConfigurationRouter# sh int fastethernet 2/0/0 Router# show interfaces fastethernet 2/0/0Router# show controllers cbus System image file is biff/rsp-jv-mz, booted via tftp from Router# show versionRouter# show diag Slot database informationUsing the ping Command to Verify Network Connectivity Upgrading Feip MicrocodeUpgrading Feip Microcode Router# show flash Router# copy tftpvip11-1 slot0vip11-1Routerconfig# microcode vip2 flash slot0vip11-1 To exit conﬁguration mode, press Ctrl-ZObtaining Documentation World Wide WebDocumentation CD-ROM Ordering DocumentationContacting TAC by Using the Cisco TAC Website Obtaining Technical AssistanceCisco.com Technical Assistance CenterObtaining Technical Assistance