Cisco Systems CX-FEIP-2FX=, CX-FEIP-1TX=, CX-FEIP-1FX=, CX-FEIP-2TX= 1FE-FX Duplex SC Connector

Page 19

FEIP Receptacles, Cables, and Pinouts

Depending on your RJ-45 interface cabling requirements, use the pinouts in Figure 13 and Figure 14.

Figure 13

FEIP

5TxD+

6TxD–

3RxD+

4RxD–

Straight-Through Cable Pinout (Connecting FEIP RJ-45 Interface to a Hub or Repeater)

Hub or repeater

5RxD+

6RxD–

3 TxD+	H3137
4 TxD–

Figure 14 Crossover Cable Pinout (RJ-45 Connections Between Hubs and Repeaters)

ub or LAN switch

3TxD+

6TxD–

1RxD+

2RxD–

Hub or LAN switch

3TxD+

6TxD–

1 RxD+	H3138
2 RxD–

Figure 15 shows the duplex SC connector (one required for both transmit and receive), and Figure 16 shows the simplex SC connector (two required, one for each transmit and receive) used for 1FE-FX optical-ﬁber connections. These multimode optical-ﬁber cables are commercially available, and they are not available from Cisco Systems.

Figure 15 1FE-FX Duplex SC Connector

H2214

Figure 16 1FE-FX Simplex SC Connector

H2399

Fast Ethernet Interface Processor (FEIP) Installation and Configuration 19

Image 19

Contents Corporate Headquarters If You Need More Information Document ContentsInstallation Prerequisites Installation PrerequisitesSoftware and Hardware Prerequisites List of Parts and Tools Safety GuidelinesElectrical Equipment Guidelines Safety Guidelines Telephone Wiring GuidelinesPreventing Electrostatic Discharge Damage Guidelines for Interface Processor Installation and Removal Orientation Shown Guidelines for Interface Processor Installation and RemovalFast Ethernet Overview Microcode OverviewParameter Ieee 802.3u 100BaseT Specifications100BASE-FX Multimode 100BASE-FX Single Mode Ieee 802.3u 100BaseT SpeciﬁcationsDTE DTE What Is the Cisco 7000 Series?Cisco 7000 Interface Processor End What Is the Cisco 7000 Series?Cisco 7505 Interface Processor End What Is the Cisco 7500 Series?Cisco 7507 Interface Processor End What Is the Cisco 7500 Series?Cisco 7513 Interface Processor End What Is the FEIP? What Is the FEIP?Fast Ethernet Interface Processor FEIP-2TX LEDs on an Feip Port Adapter Partial Faceplate View Feip LEDs1FE-FX Port Adapter Faceplate View Feip Receptacles, Cables, and PinoutsFeip Receptacles, Cables, and Pinouts 1FE-TX Port Adapter Faceplate ViewPin Description RJ-45 Connector Pinout1FE-FX Duplex SC Connector Pin Out In/Out Description MII Connector PinoutFeip Installation Feip InstallationRemoving an Feip Installing an Feip Installing an FeipAttaching Fast Ethernet Interface Cables Attaching Fast Ethernet Interface Cables Attaching the Ferrite Bead around the RJ-45 Cable Using LEDs to Check Feip Status Using LEDs to Check Feip StatusConﬁguring the Fast Ethernet Interfaces Conﬁguring the Fast Ethernet InterfacesSlot Interface Router# copy running-config startup-config Router# configure terminalRouterconfig# interface fa 1/0/0 Routerconfig-int#ip address 1.1.1.10Routerconfig# interface fastethernet 3/0/0 Configuring Interfaces-Descriptions and ExamplesRouter# sh int fa 3/0/0 Checking the Conﬁguration Using show Commands to Verify the Feip StatusStep Router# show interfaces fastethernet 2/0/0 Using show Commands to Display Interface InformationChecking the Configuration Router# sh int fastethernet 2/0/0Router# show controllers cbus Router# show version System image file is biff/rsp-jv-mz, booted via tftp fromSlot database information Router# show diagUpgrading Feip Microcode Using the ping Command to Verify Network ConnectivityUpgrading Feip Microcode Router# copy tftpvip11-1 slot0vip11-1 Router# show flashTo exit conﬁguration mode, press Ctrl-Z Routerconfig# microcode vip2 flash slot0vip11-1Ordering Documentation Obtaining DocumentationWorld Wide Web Documentation CD-ROMTechnical Assistance Center Contacting TAC by Using the Cisco TAC WebsiteObtaining Technical Assistance Cisco.comObtaining Technical Assistance