Page 30
Chapter 5 Parameters and Defaults
Operating Parameters
Related Parameters
NTPIP
Description
This parameter is the NTP IP address, required if DHCP server does not provide one.
The Cisco ATA requires an NTP Server from which to obtain Coordinated Universal Time (UTC) to time-stamp incoming calls (H.323 and SIP) to drive an external Caller-ID device.
DHCP may also supply a NTP server. If NTPIP is specified, it overwrites the value supplied by DHCP. NTPIP is ignored if its value is 0 or 0.0.0.0.
The user must not specify a port parameter. The Cisco ATA uses the default NTP port only.
Value Type
IP address
Default
0.0.0.0
Voice Configuration Menu Access Code
141
Related Parameters
AltNTPIP
Description
This parameter is the alternate NTP IP address, if you want redundancy. You can set this parameter to 0 or point to the same NTPIP if only one NTP server exists.
Value Type
IP address
Default
0.0.0.0
Voice Configuration Menu Access Code
142
Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator’s Guide (H.323)
Contents
Parameters and Defaults
A P T E R
Configuration Text File Template
Description
UIPassword
User Interface UI Parameter
Value Type
Configuration-Complete Parameter
Parameters for Configuration Method and Encryption
ToConfig
UseTFTP
Settings
Range Default Voice Configuration Menu Access Code
TftpURL
UseTFTP, CfgInterval,
CfgInterval
EncryptKey
UseTFTP, TftpURL,
320
Network Parameters
Dhcp
DHCP, StaticIp, StaticRoute, StaticNetMask,
StaticRoute
Voice Configuration Menu Access Code Related Parameters
StaticIp
DHCP, StaticRoute, StaticNetMask,
DHCP, StaticIp, StaticNetMask,
Account Information Parameters
StaticNetMask
255.255.255.0
UID0
UID1, PWD0, PWD1, UseLoginID, LoginID0, LoginID1,
This parameter is the password for the Phone 1 port
PWD0
UID0, PWD0, PWD1, UseLoginID, LoginID0, LoginID1,
UID1
This parameter is the password for the Phone 2 port
PWD1
Gateway
UseLoginID
LoginID0
LoginID1, PWD0, PWD1, UseLoginID, AutMethod,
AutMethod
LoginID1
LoginID0, PWD0, PWD1, UseLoginID, AutMethod,
Bitmap
AltGk, AltGkTimeOut, GkTimeToLive, GkId,
LoginID0, LoginID1, PWD0, PWD1, NTPIP, AltNTPIP,
GkOrProxy, AltGk, AltGkTimeOut, GkTimeToLive, GkId,
Gatekeeper Parameters
AltGkTimeOut
AltGk
AltGk, ConnectMode, page 5-28-Bit
Default Range
GkTimeToLive
GkId
Operating Parameters
Mode Parameter
Use H.323 mode -Use SIP mode
UseSIP
MediaPort
DNS2IP, UDPTOS, SigTimer, OpFlags, VLANSetting,
UDPTOS, VLANSetting,
LBRCodec
AudioMode, page 5-20-Bits 1 TxCodec, RxCodec, NumTxFrames,
AudioMode
RxCodec, TxCodec,
LBRCodec, ConnectMode, RxCodec,
RxCodec
Bit Number Definition
TxCodec
LBRCodec, NumTxFrames, TxCodec, AudioMode,
LBRCodec, NumTxFrames, RxCodec, AudioMode,
NumTxFrames
Examples
LBRCodec, RxCodec, TxCodec,
CallFeatures
CallCmd,
Bit Number
315
PaidFeatures
CallFeatures, CallCmd, CallerIdMethod, SigTimer,
Call waiting
CallerIdMethod
Polarity
0x00019e60
316
ConnectMode
TimeZone
Use G.711µ-law for fax pass-through codec
Use G.711A-law for fax pass-through codec
NTPIP, AltNTPIP,
Ntpip
AltNTPIP
AltNTPIP, TimeZone,
Udptos
DNS1IP
DNS2IP
NTPIP, TimeZone,
SigTimer
TftpURL, DHCP, VLANSetting,
OpFlags
VLANSetting
Syntax
Optional Feature Parameters
NPrintf
Example
Default Recommended Values
RingOnOffTime
IPDialPlan
DialPlan
Additional DialPlan Information
About Dial Plan Commands
Dial Plan Example 1 Default Dial Plan
Following dial plan
Dial Plan Blocking In Rule
Dial Plan Example
Following dial plans
Rule to Support Hotline/Warmline
Rule to Support Dial Prefix
Tone Parameter Syntax
Call-Progress Tone Parameters
List of Call-Progress Tone Parameters
This section contains the following topics
How to Calculate Scaling Factors
Recommended Values
Use the following formula to calculate the scaling factor a
DialTone
Default values for the nine-integer array
Specific Call-Progress Tone Parameter Information
920
ReorderTone
Cisco ATA plays the busy tone when the callee is busy
BusyTone
921
923
RingbackTone
CallWaitTone
924
925
CallCmd
AlertTone
Maximum of 248 characters
CallFeatures, PaidFeatures, CallerIdMethod, SigTimer,
930
OL-4008-01