Page 21
Chapter 5 Parameters and Defaults
Operating Parameters
Table 5-1 AudioMode Parameter Bit Definitions
Bit Number | Definition |
0 and 16 | 0/1—Disable/enable silence suppression for all audio codecs. Silence suppression is enabled by |
| default. |
| |
1 and 17 | 0—Enable selected low-bit-rate codec in addition to G.711. This setting is the default. |
| 1—Enable G.711 only. |
| |
2 and 18 | 0/1—Disable/enable fax CED tone detection. This feature is enabled by default. |
| |
3 and 19 | Reserved. |
| |
4-5 and 20-21 | DTMF Transmission Method: |
| • | 0—Always in-band. |
| • | 1—By negotiation. |
| • | 2—Always out-of-band. |
| • | 3—Reserved. |
| |
6-7 and 22-23 | Hookflash Transmission Method: |
•0—Disable sending OOB hookflash message.
•1—By negotiation (H.245 message).
•2—Always out-of-band (H.245 message).
•3—Use Q931message to send user keypad information for DTMF or hookflash transmission.
RxCodec
Description
Use this parameter to specify receiving-audio codec preference. The following values are valid:
•0—G.723 (can be selected only if LBRCodec is set to 0)
•1—G.711A-law
•2—G.711µ-law
•3—G.729A (can be selected only if LBRCodec is set to 3)
Value Type
Integer
Range
0-3
Default
2
Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator’s Guide (H.323)
Contents
A P T E R
Parameters and Defaults
Configuration Text File Template
User Interface UI Parameter
UIPassword
Description
Value Type
Configuration-Complete Parameter
Parameters for Configuration Method and Encryption
ToConfig
Range Default Voice Configuration Menu Access Code
Settings
UseTFTP
TftpURL
EncryptKey
CfgInterval
UseTFTP, CfgInterval,
UseTFTP, TftpURL,
Dhcp
Network Parameters
320
DHCP, StaticIp, StaticRoute, StaticNetMask,
StaticIp
Voice Configuration Menu Access Code Related Parameters
StaticRoute
DHCP, StaticRoute, StaticNetMask,
StaticNetMask
Account Information Parameters
DHCP, StaticIp, StaticNetMask,
255.255.255.0
This parameter is the password for the Phone 1 port
UID1, PWD0, PWD1, UseLoginID, LoginID0, LoginID1,
UID0
PWD0
UID1
UID0, PWD0, PWD1, UseLoginID, LoginID0, LoginID1,
This parameter is the password for the Phone 2 port
PWD1
Gateway
UseLoginID
LoginID0
LoginID1, PWD0, PWD1, UseLoginID, AutMethod,
LoginID0, PWD0, PWD1, UseLoginID, AutMethod,
LoginID1
AutMethod
Bitmap
GkOrProxy, AltGk, AltGkTimeOut, GkTimeToLive, GkId,
LoginID0, LoginID1, PWD0, PWD1, NTPIP, AltNTPIP,
AltGk, AltGkTimeOut, GkTimeToLive, GkId,
Gatekeeper Parameters
AltGkTimeOut
AltGk
AltGk, ConnectMode, page 5-28-Bit
Default Range
GkTimeToLive
GkId
Use H.323 mode -Use SIP mode
Mode Parameter
Operating Parameters
UseSIP
UDPTOS, VLANSetting,
DNS2IP, UDPTOS, SigTimer, OpFlags, VLANSetting,
MediaPort
LBRCodec
RxCodec, TxCodec,
AudioMode
AudioMode, page 5-20-Bits 1 TxCodec, RxCodec, NumTxFrames,
LBRCodec, ConnectMode, RxCodec,
Bit Number Definition
RxCodec
TxCodec
LBRCodec, NumTxFrames, TxCodec, AudioMode,
LBRCodec, NumTxFrames, RxCodec, AudioMode,
NumTxFrames
Examples
LBRCodec, RxCodec, TxCodec,
CallFeatures
CallCmd,
Bit Number
CallFeatures, CallCmd, CallerIdMethod, SigTimer,
PaidFeatures
315
Call waiting
CallerIdMethod
Polarity
0x00019e60
316
ConnectMode
TimeZone
Use G.711µ-law for fax pass-through codec
Use G.711A-law for fax pass-through codec
AltNTPIP
Ntpip
NTPIP, AltNTPIP,
AltNTPIP, TimeZone,
DNS2IP
DNS1IP
Udptos
NTPIP, TimeZone,
SigTimer
OpFlags
TftpURL, DHCP, VLANSetting,
VLANSetting
NPrintf
Optional Feature Parameters
Syntax
Example
Default Recommended Values
RingOnOffTime
IPDialPlan
Additional DialPlan Information
DialPlan
About Dial Plan Commands
Dial Plan Example 1 Default Dial Plan
Following dial plan
Dial Plan Blocking In Rule
Dial Plan Example
Following dial plans
Rule to Support Dial Prefix
Rule to Support Hotline/Warmline
List of Call-Progress Tone Parameters
Call-Progress Tone Parameters
Tone Parameter Syntax
This section contains the following topics
How to Calculate Scaling Factors
Recommended Values
Use the following formula to calculate the scaling factor a
Specific Call-Progress Tone Parameter Information
Default values for the nine-integer array
DialTone
920
BusyTone
Cisco ATA plays the busy tone when the callee is busy
ReorderTone
921
CallWaitTone
RingbackTone
923
924
AlertTone
CallCmd
925
Maximum of 248 characters
930
CallFeatures, PaidFeatures, CallerIdMethod, SigTimer,
OL-4008-01