Page 7
Chapter 5 Parameters and Defaults
Network Parameters
Note If the Cisco ATA configuration file is not encrypted, the value must be set to 0.
Value Type
Alphanumeric string
Range
Maximum number of characters: 8
Default
0
Voice Configuration Menu Access Code
320
Related Parameters
•TftpURL, page 5-5
Network Parameters
This section describes the parameter for enabling or disabling the use of a DHCP server to obtain IP address information, and parameters that you need to statically configure if you disable DHCP:
DHCP
Description
A DHCP server can be used to automatically set the Cisco ATA IP address, the network route IP address, the subnet mask, DNS, NTP, TFTP, and other parameters.
•1—Enable DHCP
•0—Disable DHCP
Value Type
Boolean
Range
0 or 1
Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator’s Guide (H.323)
Contents
A P T E R
Parameters and Defaults
Configuration Text File Template
Value Type
UIPassword
User Interface UI Parameter
Description
Parameters for Configuration Method and Encryption
Configuration-Complete Parameter
ToConfig
TftpURL
Settings
Range Default Voice Configuration Menu Access Code
UseTFTP
UseTFTP, TftpURL,
CfgInterval
EncryptKey
UseTFTP, CfgInterval,
DHCP, StaticIp, StaticRoute, StaticNetMask,
Network Parameters
Dhcp
320
DHCP, StaticRoute, StaticNetMask,
Voice Configuration Menu Access Code Related Parameters
StaticIp
StaticRoute
255.255.255.0
Account Information Parameters
StaticNetMask
DHCP, StaticIp, StaticNetMask,
PWD0
UID1, PWD0, PWD1, UseLoginID, LoginID0, LoginID1,
This parameter is the password for the Phone 1 port
UID0
UID1
UID0, PWD0, PWD1, UseLoginID, LoginID0, LoginID1,
PWD1
This parameter is the password for the Phone 2 port
Gateway
LoginID0
UseLoginID
LoginID1, PWD0, PWD1, UseLoginID, AutMethod,
Bitmap
LoginID1
LoginID0, PWD0, PWD1, UseLoginID, AutMethod,
AutMethod
Gatekeeper Parameters
LoginID0, LoginID1, PWD0, PWD1, NTPIP, AltNTPIP,
GkOrProxy, AltGk, AltGkTimeOut, GkTimeToLive, GkId,
AltGk, AltGkTimeOut, GkTimeToLive, GkId,
AltGk
AltGkTimeOut
AltGk, ConnectMode, page 5-28-Bit
GkTimeToLive
Default Range
GkId
UseSIP
Mode Parameter
Use H.323 mode -Use SIP mode
Operating Parameters
LBRCodec
DNS2IP, UDPTOS, SigTimer, OpFlags, VLANSetting,
UDPTOS, VLANSetting,
MediaPort
LBRCodec, ConnectMode, RxCodec,
AudioMode
RxCodec, TxCodec,
AudioMode, page 5-20-Bits 1 TxCodec, RxCodec, NumTxFrames,
Bit Number Definition
RxCodec
LBRCodec, NumTxFrames, TxCodec, AudioMode,
TxCodec
LBRCodec, NumTxFrames, RxCodec, AudioMode,
Examples
NumTxFrames
LBRCodec, RxCodec, TxCodec,
CallCmd,
CallFeatures
Bit Number
Call waiting
PaidFeatures
CallFeatures, CallCmd, CallerIdMethod, SigTimer,
315
CallerIdMethod
0x00019e60
Polarity
316
ConnectMode
Use G.711µ-law for fax pass-through codec
TimeZone
Use G.711A-law for fax pass-through codec
AltNTPIP, TimeZone,
Ntpip
AltNTPIP
NTPIP, AltNTPIP,
NTPIP, TimeZone,
DNS1IP
DNS2IP
Udptos
SigTimer
OpFlags
TftpURL, DHCP, VLANSetting,
VLANSetting
Example
Optional Feature Parameters
NPrintf
Syntax
RingOnOffTime
Default Recommended Values
IPDialPlan
Additional DialPlan Information
DialPlan
Dial Plan Example 1 Default Dial Plan
About Dial Plan Commands
Following dial plan
Dial Plan Example
Dial Plan Blocking In Rule
Following dial plans
Rule to Support Dial Prefix
Rule to Support Hotline/Warmline
This section contains the following topics
Call-Progress Tone Parameters
List of Call-Progress Tone Parameters
Tone Parameter Syntax
Recommended Values
How to Calculate Scaling Factors
Use the following formula to calculate the scaling factor a
920
Default values for the nine-integer array
Specific Call-Progress Tone Parameter Information
DialTone
921
Cisco ATA plays the busy tone when the callee is busy
BusyTone
ReorderTone
924
RingbackTone
CallWaitTone
923
Maximum of 248 characters
CallCmd
AlertTone
925
930
CallFeatures, PaidFeatures, CallerIdMethod, SigTimer,
OL-4008-01