Cisco Systems ATA 186 manual Rule to Support Hotline/Warmline, Rule to Support Dial Prefix

Page 40

Chapter 5 Parameters and Defaults

Optional Feature Parameters

For example, to enter an interdigit timeout of 12 seconds and discard dialed digits unless 911 is entered, you would use the following command:

Ic 911

Specifying your own interdigit timeout also changes the behavior of the dial plan so that the entire dial string, rather than being sent at timeout, is sent only as a result of a matching rule or time intended by a matching rule.

'H' Rule to Support Hotline/Warmline

Hotline/Warmline, also known as Private Line Automatic Ringdown (PLAR), is a line used for priority telephone service. If the Hotline feature is configured, the Cisco ATA immediately dials a pre-configured number as soon as the handset goes off hook. If the Warmline feature is configured, the Cisco ATA dials a pre-configured number if no digits were entered before the specified timer value expired when the handset went off hook.

Syntax

Hdnnnn

where d is a delay-in-seconds parameter 0-9,a-z (to support 0 to 35 seconds delay), and nnnn is the variable-length phone number to call when no digits are entered for d seconds after the handset goes off hook.

Example 1: H05551212 (Hotline configuration; the Cisco ATA immediately dials 555-1212 when the handset goes off hook.)

Example 2: H55551212 (Warmline configuration; the Cisco ATA waits for five seconds and dials 555-1212 if no digits were entered when the handset went off hook.)

'P' Rule to Support Dial Prefix

This rule is for automatic pre-pending the dial string as entered by the user with a specified prefix.

Syntax

Ptnnnn

where t is a single leading trigger character; if t is the first entered digit when making a new call, it triggers the prepending of a variable-length prefix (as specified by nnnn) in the dial string. The t character can take one of the following values:

0-9,*,#, 'n' (= any of 1-9), 'N' (any of 'n' and 0), 'a' (any of 'n',* and #), or 'A' (any of 'a' and 0);

Example:

Pn12345: Prepends 12345 to the dial string when the first entered digit is any of 1-9. The triggered digit is not removed from the dial string.

Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator’s Guide (H.323)

5-40

OL-4008-01

 

 

Image 40
Contents Parameters and Defaults A P T E RConfiguration Text File Template UIPassword User Interface UI ParameterDescription Value TypeParameters for Configuration Method and Encryption Configuration-Complete ParameterToConfig Settings Range Default Voice Configuration Menu Access CodeUseTFTP TftpURLCfgInterval EncryptKeyUseTFTP, CfgInterval, UseTFTP, TftpURL,Network Parameters Dhcp320 DHCP, StaticIp, StaticRoute, StaticNetMask,Voice Configuration Menu Access Code Related Parameters StaticIpStaticRoute DHCP, StaticRoute, StaticNetMask,Account Information Parameters StaticNetMaskDHCP, StaticIp, StaticNetMask, 255.255.255.0UID1, PWD0, PWD1, UseLoginID, LoginID0, LoginID1, This parameter is the password for the Phone 1 portUID0 PWD0UID0, PWD0, PWD1, UseLoginID, LoginID0, LoginID1, UID1PWD1 This parameter is the password for the Phone 2 portGateway LoginID0 UseLoginIDLoginID1, PWD0, PWD1, UseLoginID, AutMethod, LoginID1 LoginID0, PWD0, PWD1, UseLoginID, AutMethod,AutMethod BitmapLoginID0, LoginID1, PWD0, PWD1, NTPIP, AltNTPIP, GkOrProxy, AltGk, AltGkTimeOut, GkTimeToLive, GkId,AltGk, AltGkTimeOut, GkTimeToLive, GkId, Gatekeeper ParametersAltGk AltGkTimeOutAltGk, ConnectMode, page 5-28-Bit GkTimeToLive Default RangeGkId Mode Parameter Use H.323 mode -Use SIP modeOperating Parameters UseSIPDNS2IP, UDPTOS, SigTimer, OpFlags, VLANSetting, UDPTOS, VLANSetting,MediaPort LBRCodecAudioMode RxCodec, TxCodec,AudioMode, page 5-20-Bits 1 TxCodec, RxCodec, NumTxFrames, LBRCodec, ConnectMode, RxCodec,RxCodec Bit Number DefinitionLBRCodec, NumTxFrames, TxCodec, AudioMode, TxCodecLBRCodec, NumTxFrames, RxCodec, AudioMode, Examples NumTxFramesLBRCodec, RxCodec, TxCodec, CallCmd, CallFeaturesBit Number PaidFeatures CallFeatures, CallCmd, CallerIdMethod, SigTimer,315 Call waitingCallerIdMethod 0x00019e60 Polarity316 ConnectMode Use G.711µ-law for fax pass-through codec TimeZoneUse G.711A-law for fax pass-through codec Ntpip AltNTPIPNTPIP, AltNTPIP, AltNTPIP, TimeZone,DNS1IP DNS2IPUdptos NTPIP, TimeZone,SigTimer TftpURL, DHCP, VLANSetting, OpFlagsVLANSetting Optional Feature Parameters NPrintfSyntax ExampleRingOnOffTime Default Recommended ValuesIPDialPlan DialPlan Additional DialPlan InformationDial Plan Example 1 Default Dial Plan About Dial Plan CommandsFollowing dial plan Dial Plan Example Dial Plan Blocking In RuleFollowing dial plans Rule to Support Hotline/Warmline Rule to Support Dial PrefixCall-Progress Tone Parameters List of Call-Progress Tone ParametersTone Parameter Syntax This section contains the following topicsRecommended Values How to Calculate Scaling FactorsUse the following formula to calculate the scaling factor a Default values for the nine-integer array Specific Call-Progress Tone Parameter InformationDialTone 920Cisco ATA plays the busy tone when the callee is busy BusyToneReorderTone 921RingbackTone CallWaitTone923 924CallCmd AlertTone925 Maximum of 248 charactersCallFeatures, PaidFeatures, CallerIdMethod, SigTimer, 930OL-4008-01
Related manuals
Manual 208 pages 28.48 Kb Manual 64 pages 26.31 Kb Manual 208 pages 5.39 Kb Manual 166 pages 49.11 Kb Manual 14 pages 13.53 Kb