Cisco Systems IGX 8400 manual Summary Statistics, UXM-E Interface Cards

Page 23

UXM-E Interface Cards

Summary Statistics

You can view summary statistics for a UXM-E trunk through Cisco WAN Manager or the CLI. The CLI commands are dspportstats and dsptrkstats.

With dspportstats, you can view:

•

•

•

Port statistics

IMA statistics

ILMI/ILMI statistics

With dsptrkstats, you can view:

•

•

•

Qbin statistics

Gateway statistics

Virtual interface statistics

UXM-E Interface Cards

This section provides basic information on the interface back cards for the UXM-E. The information consists of a general description, an illustration of the card faceplate, and a table describing the connectors and status LEDs. For details on the line technology of each type of interface, see the appendix “System Speciﬁcations.”

Note The T1 and E1 back cards do not have Active and Fail LEDs to indicate card status (rather than the port status indicated by the tri-color LEDs). If a T1 or E1 back card failure is detected, all of the tri-color LEDs turn red.

The model numbers of the back cards and the order of their appearance are:

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

BC-UAI-4-155-MMF BC-UAI-4-155-SMF BC-UAI-2-155-SMF BC-UAI-2-SMFXLR BC-UAI-4-SMFXLR BC-UAI-4-STM1E BC-UAI-6-T3 BC-UAI-3-T3 BC-UAI-8-T1-DB-15 BC-UAI-4-T1-DB-15 BC-UAI-6-E3 BC-UAI-3-E3 BC-UAI-8-E1-DB-15 BC-UAI-8-E1-BNC BC-UAI-4-E1-DB-15

Trunk Cards 4-23

Image 23

Contents Trunk Cards Trunk Front Cards Card Acronym Card Name Trunk Interface CardsLoopback Test Trunk Card MaintenanceTrunk Operating Modes Universal Switching Module Enhanced Introduction to the UXM-E Trunk ModeExample Networks with UXM-Es Determining the UXM-E’s Mode of OperationUXM-Es in a Network with Heterogeneous Trafﬁc UXM-E Trunk FeaturesCard Name Card Description UXM-E InterfacesBack Cards for the UXM-E UXM-E Front Card UXM-E Status LEDs Fail Active Standby Status of Card Switchover to a Redundant UXM-EMaximum Number of UXM-Es Cabled UXM-E RedundancyUXM-E as a Clock Source Cellbus Bandwidth UsageCard Mismatch OC3 Planning for Cellbus Bandwidth AllocationATM Across a Public ATM Network Calculating Cellbus Bandwidth ChangesTrafﬁc from FastPacket-Based Cards Trafﬁc Type UXM-E in Trunk ModeRouting over Cell Trunks Only Types of Supported TrafﬁcInverse Multiplexing over ATM on IGX Trunks Types of Connections on a UXM-E TrunkAdding an IGX Feeder Line Redundancy Adding and Removing IMA Group LinksGateway Type Routing Load Type IMA ProtocolTwo-Segment Connections Routing Feeder Connection Cell Endpoint a Endpoint B TypeABR.FST Gwtypenone Three-Segment ConnectionsFeeder Connection Cell Endpoint a Endpoint B Type RT-VBR GwtypenoneOC3 STM1 SMF Activation and Conﬁguration of a UXM-E in Trunk ModeUXM-E Atfr 20Cisco IGX 8400 Series Reference IGX-UXM-E Alarms for Physical Lines and Logical TrunksSCR and PCR Policing at Less than 50 CPS on UXM-E BXM10 PCR Policing Application Example Trunk Statistics for TroubleshootingUXM-E Interface Cards Summary StatisticsOC-3/STM1 Back Cards Connectors and LEDs for SMF and MMF Back CardsConnector/Indicator Function 11 BC-UAI-4-155-SMF Faceplate 12 BC-UAI-2-155-SMF Faceplate T3 Back CardsBC-UAI-6-T3 Faceplate Connectors and LEDs for BC-UAI-6-T3 and BC-UAI-3-T3Connectors/Indicator Function 14 BC-UAI-3-T3 Faceplate E3 Back CardsBC-UAI-6-E3 Faceplate Connectors and LEDs for BC-UAI-6-E3 and BC-UAI-3-E316 BC-UAI-3-E3 Faceplate T1 Back CardsBC-UAI-8-T1-DB-15 Faceplate 18 BC-UAI-4-T1-DB-15 Faceplate E1 Back CardsBC-UAI-8-E1 DB-15 Faceplate Port 21 BC-UAI-4-E1 DB-15 Faceplate 22 BC-UAI-4-E1 BNC Faceplate Network Trunk Module Cable Redundancy for the NTMNTM Status BC-T1 Faceplate Description T1 Interface Card BC-T1BC-T1 Connections and Status LEDs 23 BC-T1 FaceplateE1 Interface Back Card BC-E1 RX-TX BC-E1 Connections and Status LEDsSubrate Interface Card BC-SR BC-SR Connections and Status LEDs Connection/Indicator FunctionY1 Interface Back Card BC-Y1 TX MON BC-Y1 Connections and Status LEDsRX MON 46Cisco IGX 8400 Series Reference