Cisco Systems IGX 8400 UXM-E Interfaces, Back Cards for the UXM-E, Card Name Card Description

Page 7

Universal Switching Module Enhanced

The maximum throughput is 310 Mbps—two times the OC-3 (STM1) rate. This maximum applies whether the back card is a 2-port or 4-port back card. In practical application, this maximum rate means that most trunk applications with an OC-3 interface would use the 2-port back card.

The UXM-E supports ATM-to-Frame Relay network and service interworking.

For the ABR connection types, the UXM-E supports EFCI marking, Explicit Rate Stamping, and Virtual Source/Virtual Destination (VS/VD).

The UXM-E supports Y-cable redundancy with hot standby for very fast switchover.

The front card has 128K cell buffers.

For statistics support, the UXM-E provides real-time statistics counters and interval statistics collection for ports, lines, trunks, and channels.

The UXM-E can form a logical trunk by grouping more than one T1 or E1 port. The name of this (purchased) option is Inverse Multiplexing over ATM (IMA).

The on-board diagnostics are loopback, self-test, and background.

UXM-E Interfaces

Table 4-4is a list of the UXM-E back cards. Figure 4-3shows the UXM-E front card. Table 4-5defines all possible combinations for the states of the front card status LEDs (Fail, Active, and Standby).

Table 4-4

Back Cards for the UXM-E

 

 

 

Card Name

 

Card Description

 

 

BC-UAI-4-155-MMF

4-port multimode fiber 155 Mbps

 

 

BC-UAI-4-155-SMF

4-port single mode fiber 155 Mbps

 

 

BC-UAI-2-155-SMF

2-port single mode fiber 155 Mbps

 

 

BC-UAI-2-SMFXLR

2-port single mode fiber XLR

 

 

BC-UAI-4-SMFXLR

4-port single mode fiber XLR

 

 

BC-UAI-4-STM1E

4-port synchronous transport module-1E

 

 

 

BC-UAI-6-T3

 

6-port T3 back card

 

 

 

BC-UAI-3-T3

 

3-port T3 back card

 

 

 

BC-UAI-6-E3

 

6-port E3 back card

 

 

 

BC-UAI-3-E3

 

3-port E3 back card

 

 

BC-UAI-4-T1-DB-15

4-port T1 back card with DB-15 connector

 

 

BC-UAI-8-T1-DB-15

8-port T1 back card with DB-15 connector

 

 

BC-UAI-4-E1-DB-15

4-port E1 back card with DB-15 connector

 

 

BC-UAI-8-E1-DB-15

8-port E1 back card with DB-15 connector

 

 

BC-UAI-4-E1-BNC

4-port E1 back card with BNC connector

 

 

BC-UAI-8-E1-BNC

8-port E1 back card with BNC connector

 

 

 

Trunk Cards 4-7

Image 7
Contents Trunk Cards Trunk Front Cards Card Acronym Card Name Trunk Interface CardsTrunk Operating Modes Trunk Card MaintenanceLoopback Test Universal Switching Module Enhanced Introduction to the UXM-E Trunk ModeExample Networks with UXM-Es Determining the UXM-E’s Mode of OperationUXM-Es in a Network with Heterogeneous Traffic UXM-E Trunk FeaturesBack Cards for the UXM-E UXM-E InterfacesCard Name Card Description UXM-E Front Card UXM-E Status LEDs Fail Active Standby Status of Card Switchover to a Redundant UXM-EMaximum Number of UXM-Es Cabled UXM-E RedundancyCard Mismatch Cellbus Bandwidth UsageUXM-E as a Clock Source OC3 Planning for Cellbus Bandwidth AllocationATM Across a Public ATM Network Calculating Cellbus Bandwidth ChangesTraffic from FastPacket-Based Cards Traffic Type UXM-E in Trunk ModeRouting over Cell Trunks Only Types of Supported TrafficInverse Multiplexing over ATM on IGX Trunks Types of Connections on a UXM-E TrunkAdding an IGX Feeder Line Redundancy Adding and Removing IMA Group LinksGateway Type Routing Load Type IMA ProtocolTwo-Segment Connections Routing Feeder Connection Cell Endpoint a Endpoint B TypeABR.FST Gwtypenone Three-Segment ConnectionsFeeder Connection Cell Endpoint a Endpoint B Type RT-VBR GwtypenoneUXM-E Atfr Activation and Configuration of a UXM-E in Trunk ModeOC3 STM1 SMF 20Cisco IGX 8400 Series Reference IGX-UXM-E Alarms for Physical Lines and Logical TrunksSCR and PCR Policing at Less than 50 CPS on UXM-E BXM10 PCR Policing Application Example Trunk Statistics for TroubleshootingUXM-E Interface Cards Summary StatisticsConnector/Indicator Function Connectors and LEDs for SMF and MMF Back CardsOC-3/STM1 Back Cards 11 BC-UAI-4-155-SMF Faceplate 12 BC-UAI-2-155-SMF Faceplate T3 Back CardsConnectors/Indicator Function Connectors and LEDs for BC-UAI-6-T3 and BC-UAI-3-T3BC-UAI-6-T3 Faceplate 14 BC-UAI-3-T3 Faceplate E3 Back CardsBC-UAI-6-E3 Faceplate Connectors and LEDs for BC-UAI-6-E3 and BC-UAI-3-E316 BC-UAI-3-E3 Faceplate T1 Back CardsBC-UAI-8-T1-DB-15 Faceplate 18 BC-UAI-4-T1-DB-15 Faceplate E1 Back CardsBC-UAI-8-E1 DB-15 Faceplate Port 21 BC-UAI-4-E1 DB-15 Faceplate 22 BC-UAI-4-E1 BNC Faceplate NTM Status Cable Redundancy for the NTMNetwork Trunk Module BC-T1 Faceplate Description T1 Interface Card BC-T1BC-T1 Connections and Status LEDs 23 BC-T1 FaceplateE1 Interface Back Card BC-E1 RX-TX BC-E1 Connections and Status LEDsSubrate Interface Card BC-SR BC-SR Connections and Status LEDs Connection/Indicator FunctionY1 Interface Back Card BC-Y1 RX MON BC-Y1 Connections and Status LEDsTX MON 46Cisco IGX 8400 Series Reference