Cisco Systems IGX 8400 manual BC-E1 Connections and Status LEDs, Rx-Tx

Page 41

Network Trunk Module

Figure 4-24 BC-E1 Faceplate

BC-E1

RX/TX

RX

TX

LOS (red)

Red alarm (red)

Yellow alarm (yellow)

AIS (green)

MFRA (red)

MFYA (yellow)

Fail (red)

Active (green)

 

 

H8317

Table 4-18

BC-E1 Connections and Status LEDs

 

 

Connector/Indicator

Function

 

 

 

RX-TX

 

Female DB-15 connector for XMT and RCV E1.

 

 

 

RX

 

BNC connector for receive E1 line.

 

 

 

TX

 

BNC connector for transmit E1 line.

 

 

 

LOS light (red)

 

Indicates loss of signal at the local end.

 

 

 

Red alarm light

 

Indicates loss of local frame alignment. On an NTM, Red indicates loss of packet

 

 

alignment.

 

 

 

Yellow alarm light

 

Indicates loss of frame alignment at remote end. On an NTM, Yellow alarm indicates loss of

 

 

packet alignment.

 

 

 

AIS light (green)

 

Indicates the presence of all ones on the line.

 

 

 

MFRA light (red)

 

Indicates loss of multiframe alignment (E1 only).

 

 

MFYA light (yellow)

Indicates loss of multiframe at remote end (E1 only).

 

 

 

Fail light (red)

 

Indicates an error. Reset the card with resetcd f. If the LED comes on again, call the TAC.

 

 

Active: light (green)

Indicates the card is in service with active circuits.

 

 

 

Trunk Cards 4-41

Image 41
Contents Trunk Cards Trunk Front Cards Card Acronym Card Name Trunk Interface CardsLoopback Test Trunk Card MaintenanceTrunk Operating Modes Universal Switching Module Enhanced Introduction to the UXM-E Trunk ModeExample Networks with UXM-Es Determining the UXM-E’s Mode of OperationUXM-Es in a Network with Heterogeneous Traffic UXM-E Trunk FeaturesCard Name Card Description UXM-E InterfacesBack Cards for the UXM-E UXM-E Front Card Maximum Number of UXM-Es Switchover to a Redundant UXM-ECabled UXM-E Redundancy UXM-E Status LEDs Fail Active Standby Status of CardUXM-E as a Clock Source Cellbus Bandwidth UsageCard Mismatch OC3 Planning for Cellbus Bandwidth AllocationATM Across a Public ATM Network Calculating Cellbus Bandwidth ChangesRouting over Cell Trunks Only UXM-E in Trunk ModeTypes of Supported Traffic Traffic from FastPacket-Based Cards Traffic TypeInverse Multiplexing over ATM on IGX Trunks Types of Connections on a UXM-E TrunkAdding an IGX Feeder Line Redundancy Adding and Removing IMA Group LinksTwo-Segment Connections IMA ProtocolRouting Feeder Connection Cell Endpoint a Endpoint B Type Gateway Type Routing Load TypeFeeder Connection Cell Endpoint a Endpoint B Type Three-Segment ConnectionsRT-VBR Gwtypenone ABR.FST GwtypenoneOC3 STM1 SMF Activation and Configuration of a UXM-E in Trunk ModeUXM-E Atfr 20Cisco IGX 8400 Series Reference SCR and PCR Policing at Less than 50 CPS on UXM-E Alarms for Physical Lines and Logical TrunksBXM IGX-UXM-E10 PCR Policing Application Example Trunk Statistics for TroubleshootingUXM-E Interface Cards Summary StatisticsOC-3/STM1 Back Cards Connectors and LEDs for SMF and MMF Back CardsConnector/Indicator Function 11 BC-UAI-4-155-SMF Faceplate 12 BC-UAI-2-155-SMF Faceplate T3 Back CardsBC-UAI-6-T3 Faceplate Connectors and LEDs for BC-UAI-6-T3 and BC-UAI-3-T3Connectors/Indicator Function 14 BC-UAI-3-T3 Faceplate E3 Back CardsBC-UAI-6-E3 Faceplate Connectors and LEDs for BC-UAI-6-E3 and BC-UAI-3-E316 BC-UAI-3-E3 Faceplate T1 Back CardsBC-UAI-8-T1-DB-15 Faceplate 18 BC-UAI-4-T1-DB-15 Faceplate E1 Back CardsBC-UAI-8-E1 DB-15 Faceplate Port 21 BC-UAI-4-E1 DB-15 Faceplate 22 BC-UAI-4-E1 BNC Faceplate Network Trunk Module Cable Redundancy for the NTMNTM Status BC-T1 Faceplate Description T1 Interface Card BC-T1BC-T1 Connections and Status LEDs 23 BC-T1 FaceplateE1 Interface Back Card BC-E1 RX-TX BC-E1 Connections and Status LEDsSubrate Interface Card BC-SR BC-SR Connections and Status LEDs Connection/Indicator FunctionY1 Interface Back Card BC-Y1 TX MON BC-Y1 Connections and Status LEDsRX MON 46Cisco IGX 8400 Series Reference