Cisco Systems IGX 8400 manual OC-3/STM1 Back Cards, Connectors and LEDs for SMF and MMF Back Cards

Page 24

UXM-E Interface Cards

BC-UAI-4-E1-BNC

OC-3/STM1 Back Cards

The OC3/STM1 back cards for the UXM-E have the single-mode fiber (SMF), multimode fiber (MMF) and electrical connections. The cards are:

BC-UAI-2-155-SMF

BC-UAI-4-155-SMF

BC-UAI-4-155-MMF

BC-UAI-2-SMFXLR

BC-UAI-4-SMFXLR

BC-UAI-4-STM1E

As indicated by the “2” or the “4” in the model number, these cards have two or four transmit and receive connectors. Each line has a tri-color LED whose color indicates its status. Each card also has a red Fail LED and a green Active LED to indicate the status of the card. Table 4-12lists the connectors and LEDs. Figure 4-11shows the four-port OC3/STM1 card. The SMF, STM1E, SMFXLR, and MMF versions appear the same. Figure 4-12shows the two-port OC3/STM1 card. For technical data on OC3/STM1 lines, see the appendix “System Specifications.”

Table 4-12

Connectors and LEDs for SMF and MMF Back Cards

 

 

Connector/Indicator

Function

 

 

Transmit and receive

SC connector for SMF and MMF

 

 

Red (on the tri-color LED)

On indicates line is active but a local alarm was detected.

 

 

Yellow (on the tri-color LED)

On indicates line is active but a remote alarm was detected.

 

 

Green (on the tri-color LED)

On indicates line is active.

 

 

 

Fail light (red)

 

An error was detected. Reset the card with resetcd f to clear it. If Fail

 

 

comes on again, call the TAC through Cisco Customer Engineering.

 

 

Active light (green)

The card is active and in service.

 

 

 

4-24Cisco IGX 8400 Series Reference

Image 24
Contents Trunk Cards Trunk Interface Cards Trunk Front Cards Card Acronym Card NameTrunk Card Maintenance Trunk Operating ModesLoopback Test Introduction to the UXM-E Trunk Mode Universal Switching Module EnhancedDetermining the UXM-E’s Mode of Operation Example Networks with UXM-EsUXM-E Trunk Features UXM-Es in a Network with Heterogeneous TrafficUXM-E Interfaces Back Cards for the UXM-ECard Name Card Description UXM-E Front Card Switchover to a Redundant UXM-E Maximum Number of UXM-EsCabled UXM-E Redundancy UXM-E Status LEDs Fail Active Standby Status of CardCellbus Bandwidth Usage Card MismatchUXM-E as a Clock Source Planning for Cellbus Bandwidth Allocation OC3Calculating Cellbus Bandwidth Changes ATM Across a Public ATM NetworkUXM-E in Trunk Mode Routing over Cell Trunks OnlyTypes of Supported Traffic Traffic from FastPacket-Based Cards Traffic TypeTypes of Connections on a UXM-E Trunk Inverse Multiplexing over ATM on IGX TrunksAdding an IGX Feeder Adding and Removing IMA Group Links Line RedundancyIMA Protocol Two-Segment ConnectionsRouting Feeder Connection Cell Endpoint a Endpoint B Type Gateway Type Routing Load TypeThree-Segment Connections Feeder Connection Cell Endpoint a Endpoint B TypeRT-VBR Gwtypenone ABR.FST GwtypenoneActivation and Configuration of a UXM-E in Trunk Mode UXM-E AtfrOC3 STM1 SMF 20Cisco IGX 8400 Series Reference Alarms for Physical Lines and Logical Trunks SCR and PCR Policing at Less than 50 CPS on UXM-EBXM IGX-UXM-ETrunk Statistics for Troubleshooting 10 PCR Policing Application ExampleSummary Statistics UXM-E Interface CardsConnectors and LEDs for SMF and MMF Back Cards Connector/Indicator FunctionOC-3/STM1 Back Cards 11 BC-UAI-4-155-SMF Faceplate T3 Back Cards 12 BC-UAI-2-155-SMF FaceplateConnectors and LEDs for BC-UAI-6-T3 and BC-UAI-3-T3 Connectors/Indicator FunctionBC-UAI-6-T3 Faceplate E3 Back Cards 14 BC-UAI-3-T3 FaceplateConnectors and LEDs for BC-UAI-6-E3 and BC-UAI-3-E3 BC-UAI-6-E3 FaceplateT1 Back Cards 16 BC-UAI-3-E3 FaceplateBC-UAI-8-T1-DB-15 Faceplate E1 Back Cards 18 BC-UAI-4-T1-DB-15 FaceplateBC-UAI-8-E1 DB-15 Faceplate Port 21 BC-UAI-4-E1 DB-15 Faceplate 22 BC-UAI-4-E1 BNC Faceplate Cable Redundancy for the NTM NTM StatusNetwork Trunk Module T1 Interface Card BC-T1 BC-T1 Faceplate Description23 BC-T1 Faceplate BC-T1 Connections and Status LEDsE1 Interface Back Card BC-E1 BC-E1 Connections and Status LEDs RX-TXSubrate Interface Card BC-SR Connection/Indicator Function BC-SR Connections and Status LEDsY1 Interface Back Card BC-Y1 BC-Y1 Connections and Status LEDs RX MONTX MON 46Cisco IGX 8400 Series Reference