Cisco Systems IGX 8400 manual Three-Segment Connections, RT-VBR Gwtypenone, ABR.FST Gwtypenone

Page 18

Universal Switching Module Enhanced

			VCC
Routing	Feeder	Connection	or		Cell
Endpoint A	Endpoint B	Type	VPC	Gateway Type	Routing	Load Type

BXM		ATFST		GW_TYPE_NWI	N/A	BDATB_LOAD

UXM-E	UFM	ATFR	N/A	GW_TYPE_NWI	N/A	BDATA_LOAD
	FRM	ATFST	N/A	GW_TYPE_NWI	N/A	BDATB_LOAD

UFM	UFM	ATFR	N/A	GW_TYPE_NWI	N/A	BDATA_LOAD
		ATFST	N/A	GW_TYPE_NWI	N/A	BDATB_LOAD
		ATFX	N/A	GW_TYPE_SIWX	N/A	BDATA_LOAD
		ATFXFST	N/A	GW_TYPE_SIWX	N/A	BDATB_LOAD
		ATFT	N/A	GW_TYPE_SIWT	N/A	BDATA_LOAD
		ATFTFST	N/A	GW_TYPE_SIWT	N/A	BDATB_LOAD

FRM	FRM	ATFR	N/A	GW_TYPE_NWI	N/A	BDATA_LOAD

Note Two-segment voice and data connections are not supported.

Figure 4-9shows an example of conﬁguring a three-segment connection for IGX feeder node functionality.

Figure 4-9 Sample Three-Segment Connections

A

	U
	U
	X		BXM/
	M-		UXM
	E


IGX-feeder

Routing network

B

			U
			U
	BXM/		X
	UXM		M-
			E



		IGX-feeder

29551

Table 4-9lists the corresponding feeder endpoints with applicable gateway and load types and connection types.

Table 4-9	Three-Segment Connections

			VCC
Feeder	Feeder	Connection	or		Cell
Endpoint A	Endpoint B	Type	VPC	Gateway Type	Routing	Load Type

UXM-E	UXM-E	CBR	Both	GW_TYPE_NONE	True	CBR_LOAD
		RT-VBR		GW_TYPE_NONE	True	CBR_LOAD
		NRT-VBR		GW_TYPE_NONE	True	VBR_LOAD
		ABR.FST		GW_TYPE_NONE	True	ABR_LOAD

4-18Cisco IGX 8400 Series Reference

Image 18

Contents Trunk Cards Trunk Interface Cards Trunk Front Cards Card Acronym Card NameTrunk Card Maintenance Trunk Operating ModesLoopback Test Introduction to the UXM-E Trunk Mode Universal Switching Module EnhancedDetermining the UXM-E’s Mode of Operation Example Networks with UXM-EsUXM-E Trunk Features UXM-Es in a Network with Heterogeneous TrafﬁcUXM-E Interfaces Back Cards for the UXM-ECard Name Card Description UXM-E Front Card Cabled UXM-E Redundancy Switchover to a Redundant UXM-EMaximum Number of UXM-Es UXM-E Status LEDs Fail Active Standby Status of CardCellbus Bandwidth Usage Card MismatchUXM-E as a Clock Source Planning for Cellbus Bandwidth Allocation OC3Calculating Cellbus Bandwidth Changes ATM Across a Public ATM NetworkTypes of Supported Trafﬁc UXM-E in Trunk ModeRouting over Cell Trunks Only Trafﬁc from FastPacket-Based Cards Trafﬁc TypeTypes of Connections on a UXM-E Trunk Inverse Multiplexing over ATM on IGX TrunksAdding an IGX Feeder Adding and Removing IMA Group Links Line RedundancyRouting Feeder Connection Cell Endpoint a Endpoint B Type IMA ProtocolTwo-Segment Connections Gateway Type Routing Load TypeRT-VBR Gwtypenone Three-Segment ConnectionsFeeder Connection Cell Endpoint a Endpoint B Type ABR.FST GwtypenoneActivation and Conﬁguration of a UXM-E in Trunk Mode UXM-E AtfrOC3 STM1 SMF 20Cisco IGX 8400 Series Reference BXM Alarms for Physical Lines and Logical TrunksSCR and PCR Policing at Less than 50 CPS on UXM-E IGX-UXM-ETrunk Statistics for Troubleshooting 10 PCR Policing Application ExampleSummary Statistics UXM-E Interface CardsConnectors and LEDs for SMF and MMF Back Cards Connector/Indicator FunctionOC-3/STM1 Back Cards 11 BC-UAI-4-155-SMF Faceplate T3 Back Cards 12 BC-UAI-2-155-SMF FaceplateConnectors and LEDs for BC-UAI-6-T3 and BC-UAI-3-T3 Connectors/Indicator FunctionBC-UAI-6-T3 Faceplate E3 Back Cards 14 BC-UAI-3-T3 FaceplateConnectors and LEDs for BC-UAI-6-E3 and BC-UAI-3-E3 BC-UAI-6-E3 FaceplateT1 Back Cards 16 BC-UAI-3-E3 FaceplateBC-UAI-8-T1-DB-15 Faceplate E1 Back Cards 18 BC-UAI-4-T1-DB-15 FaceplateBC-UAI-8-E1 DB-15 Faceplate Port 21 BC-UAI-4-E1 DB-15 Faceplate 22 BC-UAI-4-E1 BNC Faceplate Cable Redundancy for the NTM NTM StatusNetwork Trunk Module T1 Interface Card BC-T1 BC-T1 Faceplate Description23 BC-T1 Faceplate BC-T1 Connections and Status LEDsE1 Interface Back Card BC-E1 BC-E1 Connections and Status LEDs RX-TXSubrate Interface Card BC-SR Connection/Indicator Function BC-SR Connections and Status LEDsY1 Interface Back Card BC-Y1 BC-Y1 Connections and Status LEDs RX MONTX MON 46Cisco IGX 8400 Series Reference