Cisco Systems OL-17037-01 Configuring the Syslog Server for Access Points, Show ap config global

Page 26

Chapter 7 Controlling Lightweight Access Points

Autonomous Access Points Converted to Lightweight Mode

Configuring the Syslog Server for Access Points

Follow these steps to configure the syslog server for access points using the controller CLI.

Step 1 Perform one of the following:

•To configure a global syslog server for all access points that join this controller, enter this command: config ap syslog host global syslog_server_IP_address

Note By default, the global syslog server IP address for all access points is 255.255.255.255. Make sure that the access points can reach the subnet on which the syslog server resides before configuring the syslog server on the controller. If the access points cannot reach this subnet, the access points are unable to send out syslog messages.

•To configure a syslog server for a specific access point, enter this command: config ap syslog host specific Cisco_AP syslog_server_IP_address

Note By default, the syslog server IP address for each access point is 0.0.0.0, indicating that it is not yet set. When the default value is used, the global access point syslog server IP address is pushed to the access point.

Step 2 To save your changes, enter this command:

save config

Step 3 To see the global syslog server settings for all access points that join the controller, enter this command:

show ap config global

Information similar to the following appears:

AP global system logging host

255.255.255.255

Step 4 To see the syslog server settings for a specific access point, enter this command:

show ap config general Cisco_AP

Viewing Access Point Join Information

Join statistics for an access point that sent a CAPWAP discovery request to the controller at least once are maintained on the controller even if the access point is rebooted or disconnected. These statistics are removed only if the controller is rebooted.

Use these CLI commands to view access point join information:

•To see the MAC addresses of all the access points that are joined to the controller or that have tried to join, enter this command:

show ap join stats summary all

	Cisco Wireless LAN Controller Configuration Guide
7-26	OL-17037-01

Image 26

Contents Controlling Lightweight Access Points Controller Discovery Process Access Point Communication ProtocolsGuidelines for Using Capwap Page Config network master-base disable Verifying that Access Points Join the ControllerConfig network master-base enable Debugging Capwap Configuring Global Credentials for Access PointsViewing Capwap MTU Information Global Configuration All APs Details for Credentials Show ap summary Save configShow ap config general CiscoAP Configuring Authentication for Access Points Lwapp ap dot1x username username password passwordUsing the GUI to Configure Authentication for Access Points ControllerCisco Wireless LAN Controller Configuration Guide Using the CLI to Configure Authentication for Access Points Config ap dot1xuser add username user password password allConfig ap dot1xuser disable all CiscoAP AP Dot1x User Mode field shows CustomizedEmbedded Access Points Configuring the Switch for AuthenticationDns-server ipaddress Default-router ipaddress Ip dhcp pool poolnameAutonomous Access Points Converted to Lightweight Mode Reverting from Lightweight Mode to Autonomous Mode Using a Controller to Return to a Previous ReleaseAuthorizing Access Points Using MICs Authorizing Access PointsAuthorizing Access Points Using SSCs Authorizing Access Points Using LSCs Using the GUI to Configure LSCConfig certificate lsc ca-cert add delete Config certificate lsc enable disableConfig certificate lsc ca-server http//urlport/path Config certificate lsc other-params keysizeShow certificate lsc summary Config certificate lsc ap-provision auth-list add APmacaddrConfig certificate lsc ap-provision revert-cert retries Using the GUI to Authorize Access Points Show certificate lsc ap-provisionConfig auth-list add mic ssc lsc apmac apkey Using the CLI to Authorize Access PointsConfig auth-list ap-policy mic ssc lsc enable disable Show auth-listUsing Dhcp Option 43 and Dhcp Option Troubleshooting the Access Point Join ProcessControlling Lightweight Access Points Show ap config global Configuring the Syslog Server for Access PointsViewing Access Point Join Information Show ap join stats summary allJoined Converted Access Points Send Radio Core Dumps to Controller Debug ap enable disable command cmd CiscoAPShow ap crash-file Using the CLI to Retrieve Radio Core DumpsUsing the GUI to Upload Radio Core Dumps Using the CLI to Upload Radio Core Dumps Transfer upload startUploading Memory Core Dumps from Converted Access Points Using the GUI to Upload Access Point Core DumpsDisplay of MAC Addresses for Converted Access Points Using the CLI to Upload Access Point Core DumpsSupporting Oversized Access Point Images Config ap reset-button enable disable ap-nameallCisco Workgroup Bridges WGB ExampleGuidelines for Using WGBs Configure terminal Show dot11 association Sample WGB ConfigurationUsing the GUI to View the Status of Workgroup Bridges 11 Clients Detail 12 WGB Wired Clients Debug dhcp message enable Debug dhcp packet enable Using the CLI to View the Status of Workgroup BridgesUsing the CLI to Debug WGB Issues Debug dot11 mobile enable Debug dot11 state enableConfiguring Backup Controllers Using the GUI to Configure Backup Controllers 14 Global Configuration15 All APs Details for High Availability Using the CLI to Configure Backup Controllers Config advanced timers ap-discovery-timeout interval Config advanced timers auth-timeout intervalConfiguring Failover Priority for Access Points 130016 Global Configuration Using the CLI to View Failover Priority Settings EnabledConfiguring Country Codes Guidelines for Configuring Multiple Country CodesUsing the GUI to Configure Country Codes 19 All APs Details for Advanced Show country Using the CLI to Configure Country CodesShow country supported Show country channels Config 802.11a enable network config 802.11b enable network Controlling Lightweight Access Points Guidelines for Migration Migrating Access Points to the -U Regulatory DomainConfig country J3 Show ap migrateConfig ap migrate j52w52 all apname Using the W56 Band in Japan Dynamic Frequency SelectionOptimizing Rfid Tracking on Access Points Using the GUI to Optimize Rfid Tracking on Access Points20 802.11b/g/n Cisco APs Configure Config 802.11b enable CiscoAP Using the CLI to Optimize Rfid Tracking on Access PointsConfig ap monitor-mode tracking-opt CiscoAP Config advanced probe limit numprobes interval Configuring Probe Request ForwardingConfig advanced probe filter enable disable Show ap monitor-mode summaryInventory Performing a Link Test 22 All APs Details for InventoryUsing the GUI to Perform a Link Test Link Test Configuring Link Latency Using the CLI to Perform a Link TestUsing the GUI to Configure Link Latency 25 All APs Details for AdvancedUsing the CLI to Configure Link Latency Config ap link-latency enable disable CiscoAP allConfiguring Power over Ethernet Config ap link-latency reset CiscoAPUsing the GUI to Configure Power over Ethernet EPoE Power EPoE Mode 15.4 W Optimized 20 WCisco Wireless LAN Controller Configuration Guide Config ap power injector enable CiscoAP all override Using the CLI to Configure Power over EthernetConfig ap power injector enable CiscoAP all installed Debug ap command led flash seconds CiscoAP Configuring Flashing LEDsUsing the GUI to View Clients Viewing ClientsControlling Lightweight Access Points Viewing Clients 28 Search Clients 29 Clients Detail Using the CLI to View Clients AP MACS69 OL-17037-01