Cisco Systems OL-17037-01 Configuring Probe Request Forwarding, Show ap monitor-mode summary

Page 62

Chapter 7 Controlling Lightweight Access Points

Configuring Probe Request Forwarding

Step 9 To see a summary of all access points in monitor mode, enter this command:

show ap monitor-mode summary

Information similar to the following appears:

AP Name

Ethernet MAC

Status

Scanning Channel List

------------------

--------------------

----------

------------------------

AP1131:46f2.98ac

00:16:46:f2:98:ac

Tracking

1, 6, NA, NA

 

 

 

 

Configuring Probe Request Forwarding

Probe requests are 802.11 management frames sent by clients to request information about the capabilities of SSIDs. By default, access points forward acknowledged probe requests to the controller for processing. Acknowledged probe requests are probe requests for SSIDs that are supported by the access point. If desired, you can configure access points to forward both acknowledged and unacknowledged probe requests to the controller. The controller can use the information from unacknowledged probe requests to improve location accuracy.

Using the controller CLI, follow these steps to configure probe request filtering and rate limiting.

Step 1 To enable or disable the filtering of probe requests forwarded from an access point to the controller, enter this command:

config advanced probe filter {enable disable}

If you enable probe filtering, the default filter setting, the access point forwards only acknowledged probe requests to the controller. If you disable probe filtering, the access point forwards both acknowledged and unacknowledged probe requests to the controller.

Step 2 To limit the number of probe requests sent to the controller per client per access point radio in a given interval, enter this command:

config advanced probe limit num_probes interval

num_probes is the number of probe requests (from 1 to 100) forwarded to the controller per client per access point radio in a given interval.

interval is the probe limit interval (from 100 to 10000 milliseconds).

The default value for num_probes is 2 probe requests, and the default value for interval is 500 milliseconds.

Step 3 To save your changes, enter this command: save config

Step 4 To view the probe request forwarding configuration, enter this command:

show advanced probe

Information similar to the following appears:

Probe

request

filtering

Enabled

Probes fwd to

controller per client per radio....

2

Probe

request

rate-limiting interval

500 msec

 

Cisco Wireless LAN Controller Configuration Guide

7-62

OL-17037-01

Image 62
Contents Controlling Lightweight Access Points Controller Discovery Process Access Point Communication ProtocolsGuidelines for Using Capwap Page Config network master-base disable Verifying that Access Points Join the ControllerConfig network master-base enable Debugging Capwap Configuring Global Credentials for Access PointsViewing Capwap MTU Information Global Configuration All APs Details for Credentials Show ap summary Save configShow ap config general CiscoAP Configuring Authentication for Access Points Lwapp ap dot1x username username password passwordUsing the GUI to Configure Authentication for Access Points ControllerCisco Wireless LAN Controller Configuration Guide Using the CLI to Configure Authentication for Access Points Config ap dot1xuser add username user password password allConfig ap dot1xuser disable all CiscoAP AP Dot1x User Mode field shows CustomizedEmbedded Access Points Configuring the Switch for AuthenticationDns-server ipaddress Default-router ipaddress Ip dhcp pool poolnameAutonomous Access Points Converted to Lightweight Mode Reverting from Lightweight Mode to Autonomous Mode Using a Controller to Return to a Previous ReleaseAuthorizing Access Points Using MICs Authorizing Access PointsAuthorizing Access Points Using SSCs Authorizing Access Points Using LSCs Using the GUI to Configure LSCConfig certificate lsc ca-cert add delete Config certificate lsc enable disableConfig certificate lsc ca-server http//urlport/path Config certificate lsc other-params keysizeShow certificate lsc summary Config certificate lsc ap-provision auth-list add APmacaddrConfig certificate lsc ap-provision revert-cert retries Using the GUI to Authorize Access Points Show certificate lsc ap-provisionConfig auth-list add mic ssc lsc apmac apkey Using the CLI to Authorize Access PointsConfig auth-list ap-policy mic ssc lsc enable disable Show auth-listUsing Dhcp Option 43 and Dhcp Option Troubleshooting the Access Point Join ProcessControlling Lightweight Access Points Show ap config global Configuring the Syslog Server for Access PointsViewing Access Point Join Information Show ap join stats summary allJoined Converted Access Points Send Radio Core Dumps to Controller Debug ap enable disable command cmd CiscoAPShow ap crash-file Using the CLI to Retrieve Radio Core DumpsUsing the GUI to Upload Radio Core Dumps Using the CLI to Upload Radio Core Dumps Transfer upload startUploading Memory Core Dumps from Converted Access Points Using the GUI to Upload Access Point Core DumpsDisplay of MAC Addresses for Converted Access Points Using the CLI to Upload Access Point Core DumpsSupporting Oversized Access Point Images Config ap reset-button enable disable ap-nameallCisco Workgroup Bridges WGB ExampleGuidelines for Using WGBs Configure terminal Show dot11 association Sample WGB ConfigurationUsing the GUI to View the Status of Workgroup Bridges 11 Clients Detail 12 WGB Wired Clients Debug dhcp message enable Debug dhcp packet enable Using the CLI to View the Status of Workgroup BridgesUsing the CLI to Debug WGB Issues Debug dot11 mobile enable Debug dot11 state enableConfiguring Backup Controllers Using the GUI to Configure Backup Controllers 14 Global Configuration15 All APs Details for High Availability Using the CLI to Configure Backup Controllers Config advanced timers ap-discovery-timeout interval Config advanced timers auth-timeout intervalConfiguring Failover Priority for Access Points 130016 Global Configuration Using the CLI to View Failover Priority Settings EnabledConfiguring Country Codes Guidelines for Configuring Multiple Country CodesUsing the GUI to Configure Country Codes 19 All APs Details for Advanced Show country Using the CLI to Configure Country CodesShow country supported Show country channels Config 802.11a enable network config 802.11b enable network Controlling Lightweight Access Points Guidelines for Migration Migrating Access Points to the -U Regulatory DomainConfig country J3 Show ap migrateConfig ap migrate j52w52 all apname Using the W56 Band in Japan Dynamic Frequency SelectionOptimizing Rfid Tracking on Access Points Using the GUI to Optimize Rfid Tracking on Access Points20 802.11b/g/n Cisco APs Configure Config 802.11b enable CiscoAP Using the CLI to Optimize Rfid Tracking on Access PointsConfig ap monitor-mode tracking-opt CiscoAP Config advanced probe limit numprobes interval Configuring Probe Request ForwardingConfig advanced probe filter enable disable Show ap monitor-mode summaryInventory Performing a Link Test 22 All APs Details for InventoryUsing the GUI to Perform a Link Test Link Test Configuring Link Latency Using the CLI to Perform a Link TestUsing the GUI to Configure Link Latency 25 All APs Details for AdvancedUsing the CLI to Configure Link Latency Config ap link-latency enable disable CiscoAP allConfiguring Power over Ethernet Config ap link-latency reset CiscoAPUsing the GUI to Configure Power over Ethernet EPoE Power EPoE Mode 15.4 W Optimized 20 WCisco Wireless LAN Controller Configuration Guide Config ap power injector enable CiscoAP all override Using the CLI to Configure Power over EthernetConfig ap power injector enable CiscoAP all installed Debug ap command led flash seconds CiscoAP Configuring Flashing LEDsUsing the GUI to View Clients Viewing ClientsControlling Lightweight Access Points Viewing Clients 28 Search Clients 29 Clients Detail Using the CLI to View Clients AP MACS69 OL-17037-01