Cisco Systems OL-20932-02 manual Cisco Physical Access Gateway Ports and Connectors Top View

Page 28

Chapter 2 Installing and Configuring the Cisco Physical Access Gateway

Physical Overview and Port Description

Figure 2-3 Cisco Physical Access Gateway Ports and Connectors: Top View

2

5

6

7

8

9

10

4

3

2

1

11

187039

1

2

3

4

5

6

Power—Two-pin connector for Voltage In (VIN) and Ground (GND) to connect a 12 to 24 VDC external power source.

CAN—A three-wire CAN bus is used to connect additional modules, including the Cisco Reader Module, Cisco Input Module, and Cisco Output Module.

Note Modules are connected using the CAN1 interface. The CAN2 interface is not supported in this release.

SVR (Server)—When the LED is steady green, the Gateway is connected to a Cisco PAM appliance.

Fast Ethernet interfaces—There are two 10/100 BASE-TX RJ-45 connectors:

•ETH 0: connects the Gateway to the network. ETH 0 also supports Power over Ethernet (PoE) for the device (optional).

•ETH 1: connects the device to a PC to access the device configuration web page.

Serial interface—The RS-485 interface is not supported in this release.

Wiegand interface—This interface can be configured as the following:

•One 10-pin Wiegand/clock and data reader interface to connect a single door reader.

•Two 5-pin Wiegand/clock and data interfaces to connect two door readers (for installations where a 5-pin interface is sufficient).

Note Disconnect power from the Gateway or Reader module before connecting reader devices to the modules. Connecting a reader device when the modules are powered can cause the Gateway or Reader module to malfunction.

Cisco Physical Access Gateway User Guide

2-4	OL-20932-02

Image 28

Contents Cisco Physical Access Gateway User Guide Americas HeadquartersCisco Physical Access Gateway User Guide N T E N T S Safety Warnings Environmental Specifications A-1 Contents Cisco Physical Access Gateway User Guide Safety Warnings PrefaceViii Overview Feature Benefit Cisco Physical Access GatewaySystem Overview Support for Multiple Cisco Physical Access Gateways Related DocumentationCisco Physical Access Manager Optional Expansion Modules Module Features 30VDCCan Bus Connections for Optional Modules Installation and Configuration Summary Door Device Wiring Requirements Typical Wire Function Wires Gauge Type UseUnderstanding Supervised and Unsupervised Input Devices Example of a Supervised Door Sensor Power Options and Requirements Power OptionsModule Power over Ethernet PoE Through 24V DC Current Draw RequirementsInstalling Surge Suppressors on Output Device Connections Connect Reader Devices with Module Power OffMounting a Gateway or Optional Module Wall Mounting a Gateway or Optional ModuleWall Mount Installation Kit Contents OL-20932-02 Contents Cisco Physical Access Gateway OverviewPackage Contents Physical Overview and Port DescriptionCisco Physical Access Gateway Ports and Connectors Top View Status LED StatusDescription Status Description Input Port LEDsProcedure Installing the Cisco Physical Access GatewayBefore You Begin Power Connections for the Cisco Physical Access Gateway Label Description Wire Connection Chassis One Reader First Reader in aHcrd 271592 271593 CAN+ 271591 Understanding Network Time Protocol NTP Settings Connecting a PC to the Gateway Entering the Gateway Network Settings 12 Login Screen for the Cisco Physical Access Gateway13 Network Settings for the Cisco Physical Access Gateway Changing the User Password Enter the Current Password Enter the New PasswordUpgrading the Gateway Firmware Using a Direct Connection 15 Image Management for the Cisco Physical Access GatewayOption 1 Local Disk Option 2 Remote Tftp ServerDisplaying Serial Numbers and Other Information Installing and Configuring the Cisco Physical Access Gateway Soft Reset Powercycle Resetting the Cisco Physical Access GatewayHard Reset Restore Factory Defaults Connecting a Cisco Reader Module Door Related Hardware Cisco Reader Module Ports and Connectors Cisco Reader Module Ports and Connectors Top View Cisco Physical Access Gateway User Guide OL-20932-02 Installing the Cisco Reader Module Status LEDsPower Connection for the Cisco Reader Module 271600 +12v PWR red Output RED brown GRN orange 271592 271593 Connecting a Cisco Input Module Can connection Additional Connector plugs Cisco Input Module Ports and Connectors Top View Installing the Cisco Input Module Power Connections for the Input and Output Modules Can Connections Input and Output Modules 1K,, 1% Connecting a Cisco Output Module Connecting a Cisco Output Module Package Contents Cisco Output Module Ports and Connectors Cisco Output Module Ports and Connectors Top View Output Module LEDs Installing the Cisco Output Module Power Connections for the Cisco Output Module CAN+ Cisco Physical Access Gateway User Guide OL-20932-02 OL-20932-02 Safety Warnings Statement 1071-Warning DefinitionWarnung Wichtige Sicherheitshinweise Avvertenza Importanti Istruzioni Sulla SicurezzaAviso Instruções Importantes DE Segurança Guarde Estas InstruçõesGEM Disse Anvisninger Page Statement 369-Power over Ethernet PoE Ieee 802.3af Statement 353-This Product Must be Connected Appendix 6 Safety Warnings Statement 1040-Product Disposal Statement 1004-Installation Instructions Cisco Physical Access Gateway User Guide OL-20932-02 Environmental Specifications GatewayEnvironmental Specifications for the Cisco Reader Module Environmental Specifications for the Cisco Input ModuleEnvironmental Specifications for the Cisco Output Module OL-20932-02