Cisco Systems OL-20932-02 manual Output Module LEDs

Page 73

Chapter 5 Connecting a Cisco Output Module

Physical Overview and Port Description

4

8

9

Output Interfaces

Eight Form C (5A @ 30V) relay outputs. Each output can be configured as either Normally Closed (NC) or Normally Open (NO).

•C & NO connection: The relay is normally open. The circuit is closed when triggered.

•C & NC connection: The relay is normally closed. The circuit is opened when triggered.

Notes:

•Install surge protection between the output device and the Cisco PAM module, as described in the “Installing Surge Suppressors on Output Device Connections” section on page 1-13.

•Common (C) is always used, and either NC or NO is used to complete the connection.

•All Generic Output devices installed in Cisco PAM systems prior to release 1.1.0, were connected to the Gateway, Reader, or Output modules with the wiring reversed. If upgrading to Cisco PAM release 1.1.0 from an earlier release, disconnect all Generic Output devices and do the following:

–Connect Normally Open devices to the N.O. and C connectors on the Gateway, Reader, or Output module.

–Connect Normally Closed devices to the N.C. and C connectors on the Gateway, Reader, or Output module.

PF

Power fail input: an unsupervised input that raises a “power fail” alarm when the circuit is open. Can be configured as an additional unsupervised port. An unsupervised input indicates only normal or alarm. The corresponding LED is red when circuit is open (when no input is connected).

TM

Tamper input: an unsupervised input that raises a “tamper” alarm when the circuit is open. Can be configured as an additional unsupervised port. An unsupervised input indicates only normal or alarm. The corresponding LED is red when circuit is open (when no input is connected).

Status LEDs

Each output port includes a status LED that indicates the following information:

Table 5-1 Output Module LEDs

Status	Description

Off	Output not configured

Solid Green	Output configured and in default state

Blinking Green	Output configured and active

Cisco Physical Access Gateway User Guide

	OL-20932-02	5-5

Image 73

Contents Americas Headquarters Cisco Physical Access Gateway User GuideCisco Physical Access Gateway User Guide N T E N T S Safety Warnings Environmental Specifications A-1 Contents Cisco Physical Access Gateway User Guide Preface Safety WarningsViii Overview Feature Benefit Cisco Physical Access GatewaySystem Overview Related Documentation Support for Multiple Cisco Physical Access GatewaysCisco Physical Access Manager Optional Expansion Modules 30VDC Module FeaturesCan Bus Connections for Optional Modules Installation and Configuration Summary Typical Wire Function Wires Gauge Type Use Door Device Wiring RequirementsUnderstanding Supervised and Unsupervised Input Devices Example of a Supervised Door Sensor Power Options Power Options and RequirementsModule Power over Ethernet PoE Through 24V DC Current Draw RequirementsConnect Reader Devices with Module Power Off Installing Surge Suppressors on Output Device ConnectionsWall Mounting a Gateway or Optional Module Mounting a Gateway or Optional ModuleWall Mount Installation Kit Contents OL-20932-02 Contents Overview Cisco Physical Access GatewayPhysical Overview and Port Description Package ContentsCisco Physical Access Gateway Ports and Connectors Top View Status LED StatusDescription Input Port LEDs Status DescriptionProcedure Installing the Cisco Physical Access GatewayBefore You Begin Power Connections for the Cisco Physical Access Gateway Chassis One Reader First Reader in a Label Description Wire ConnectionHcrd 271592 271593 CAN+ 271591 Understanding Network Time Protocol NTP Settings Connecting a PC to the Gateway 12 Login Screen for the Cisco Physical Access Gateway Entering the Gateway Network Settings13 Network Settings for the Cisco Physical Access Gateway Enter the Current Password Enter the New Password Changing the User Password15 Image Management for the Cisco Physical Access Gateway Upgrading the Gateway Firmware Using a Direct ConnectionOption 2 Remote Tftp Server Option 1 Local DiskDisplaying Serial Numbers and Other Information Installing and Configuring the Cisco Physical Access Gateway Soft Reset Powercycle Resetting the Cisco Physical Access GatewayHard Reset Restore Factory Defaults Connecting a Cisco Reader Module Door Related Hardware Cisco Reader Module Ports and Connectors Cisco Reader Module Ports and Connectors Top View Cisco Physical Access Gateway User Guide OL-20932-02 Status LEDs Installing the Cisco Reader ModulePower Connection for the Cisco Reader Module 271600 +12v PWR red Output RED brown GRN orange 271592 271593 Connecting a Cisco Input Module Can connection Additional Connector plugs Cisco Input Module Ports and Connectors Top View Installing the Cisco Input Module Power Connections for the Input and Output Modules Can Connections Input and Output Modules 1K,, 1% Connecting a Cisco Output Module Connecting a Cisco Output Module Package Contents Cisco Output Module Ports and Connectors Cisco Output Module Ports and Connectors Top View Output Module LEDs Installing the Cisco Output Module Power Connections for the Cisco Output Module CAN+ Cisco Physical Access Gateway User Guide OL-20932-02 OL-20932-02 Statement 1071-Warning Definition Safety WarningsAvvertenza Importanti Istruzioni Sulla Sicurezza Warnung Wichtige SicherheitshinweiseGuarde Estas Instruções Aviso Instruções Importantes DE SegurançaGEM Disse Anvisninger Page Statement 369-Power over Ethernet PoE Ieee 802.3af Statement 353-This Product Must be Connected Appendix 6 Safety Warnings Statement 1040-Product Disposal Statement 1004-Installation Instructions Cisco Physical Access Gateway User Guide OL-20932-02 Gateway Environmental SpecificationsEnvironmental Specifications for the Cisco Input Module Environmental Specifications for the Cisco Reader ModuleEnvironmental Specifications for the Cisco Output Module OL-20932-02