Cisco Systems OL-20932-02 manual Installing the Cisco Physical Access Gateway, Before You Begin

Page 31

Chapter 2 Installing and Configuring the Cisco Physical Access Gateway

Installing the Cisco Physical Access Gateway

Installing the Cisco Physical Access Gateway

•Before You Begin, page 2-7

•Procedure, page 2-7

Before You Begin

Before you install a Cisco Physical Access Gateway, verify the following:

•Verify that the module has access to a power source. See the “Power Options and Requirements” section on page 1-12for more information.

•Verify that you have the necessary mounting brackets or other hardware. See the “Mounting a Gateway or Optional Module” section on page 1-14.

Procedure

To install the Cisco Physical Access Gateway, perform the following procedure:

Step 1 Mount the Gateway to a wall. See the “Mounting a Gateway or Optional Module” section on page 1-14for more information.

Step 2 Connect the Gateway to a power source.

•If using a DC power source, insert a two-pin connector plug into the DC power port (Figure 2-4), and connect the Voltage In (VIN) and ground (GND) wires.

•If using PoE, connect an Ethernet cable from the IP network to the ETH0 port (Figure 2-4).

See the “Power Options and Requirements” section on page 1-12for more information.

Cisco Physical Access Gateway User Guide

	OL-20932-02	2-7

Image 31

Contents Americas Headquarters Cisco Physical Access Gateway User GuideCisco Physical Access Gateway User Guide N T E N T S Safety Warnings Environmental Specifications A-1 Contents Cisco Physical Access Gateway User Guide Preface Safety WarningsViii Overview Feature Benefit Cisco Physical Access GatewaySystem Overview Related Documentation Support for Multiple Cisco Physical Access GatewaysCisco Physical Access Manager Optional Expansion Modules 30VDC Module FeaturesCan Bus Connections for Optional Modules Installation and Configuration Summary Typical Wire Function Wires Gauge Type Use Door Device Wiring RequirementsUnderstanding Supervised and Unsupervised Input Devices Example of a Supervised Door Sensor Current Draw Requirements Power Options and RequirementsPower Options Module Power over Ethernet PoE Through 24V DCConnect Reader Devices with Module Power Off Installing Surge Suppressors on Output Device ConnectionsWall Mounting a Gateway or Optional Module Mounting a Gateway or Optional ModuleWall Mount Installation Kit Contents OL-20932-02 Contents Overview Cisco Physical Access GatewayPhysical Overview and Port Description Package ContentsCisco Physical Access Gateway Ports and Connectors Top View Status LED StatusDescription Input Port LEDs Status DescriptionProcedure Installing the Cisco Physical Access GatewayBefore You Begin Power Connections for the Cisco Physical Access Gateway Chassis One Reader First Reader in a Label Description Wire ConnectionHcrd 271592 271593 CAN+ 271591 Understanding Network Time Protocol NTP Settings Connecting a PC to the Gateway 12 Login Screen for the Cisco Physical Access Gateway Entering the Gateway Network Settings13 Network Settings for the Cisco Physical Access Gateway Enter the Current Password Enter the New Password Changing the User Password15 Image Management for the Cisco Physical Access Gateway Upgrading the Gateway Firmware Using a Direct ConnectionOption 2 Remote Tftp Server Option 1 Local DiskDisplaying Serial Numbers and Other Information Installing and Configuring the Cisco Physical Access Gateway Soft Reset Powercycle Resetting the Cisco Physical Access GatewayHard Reset Restore Factory Defaults Connecting a Cisco Reader Module Door Related Hardware Cisco Reader Module Ports and Connectors Cisco Reader Module Ports and Connectors Top View Cisco Physical Access Gateway User Guide OL-20932-02 Status LEDs Installing the Cisco Reader ModulePower Connection for the Cisco Reader Module 271600 +12v PWR red Output RED brown GRN orange 271592 271593 Connecting a Cisco Input Module Can connection Additional Connector plugs Cisco Input Module Ports and Connectors Top View Installing the Cisco Input Module Power Connections for the Input and Output Modules Can Connections Input and Output Modules 1K,, 1% Connecting a Cisco Output Module Connecting a Cisco Output Module Package Contents Cisco Output Module Ports and Connectors Cisco Output Module Ports and Connectors Top View Output Module LEDs Installing the Cisco Output Module Power Connections for the Cisco Output Module CAN+ Cisco Physical Access Gateway User Guide OL-20932-02 OL-20932-02 Statement 1071-Warning Definition Safety WarningsAvvertenza Importanti Istruzioni Sulla Sicurezza Warnung Wichtige SicherheitshinweiseGuarde Estas Instruções Aviso Instruções Importantes DE SegurançaGEM Disse Anvisninger Page Statement 369-Power over Ethernet PoE Ieee 802.3af Statement 353-This Product Must be Connected Appendix 6 Safety Warnings Statement 1040-Product Disposal Statement 1004-Installation Instructions Cisco Physical Access Gateway User Guide OL-20932-02 Gateway Environmental SpecificationsEnvironmental Specifications for the Cisco Input Module Environmental Specifications for the Cisco Reader ModuleEnvironmental Specifications for the Cisco Output Module OL-20932-02