Cisco Systems OL-20932-02 manual LED Status, Description

Page 29

Chapter 2 Installing and Configuring the Cisco Physical Access Gateway

Physical Overview and Port Description

7Input interfaces—Three input interfaces used to sense the contact closure. Each input can be configured as supervised or unsupervised and can be configured to sense a Normally Open (NO) or Normally Closed (NC) contact.

•An unsupervised input senses a simple contact closure state, including Normal or Alarm. When connected to open contacts, the terminal voltage range is 4V to 5V. For closed contacts, the voltage range is 0V to 0.7V.

•A supervised input senses four contact states, including Normal, Alarm, Open and Short. These inputs require 1K End-Of-Line (EOL) termination resistors installed at the contacts (two resistors are included in the accessory kits for each Input port).

8Output interfaces—Three Form C (5A @ 30V) relay output interfaces. Each output connection can be configured as either Normally Closed (NC) or Normally Open (NO).

•C & NO connection: The relay is normally open. The circuit is closed when triggered.

•C & NC connection: The relay is normally closed. The circuit is opened when triggered.

Notes:

•Install surge protection between the output device and the Cisco PAM module, as described in the “Installing Surge Suppressors on Output Device Connections” section on page 1-13.

•Common (C) is always used, and either NC or NO is used to complete the connection.

•All Generic Output devices installed in Cisco PAM systems prior to release 1.1.0, were connected to the Gateway, Reader, or Output modules with the wiring reversed. If upgrading to Cisco PAM release 1.1.0 from an earlier release, disconnect all Generic Output devices and do the following:

–Connect Normally Open devices to the N.O. and C connectors on the Gateway, Reader, or Output module.

–Connect Normally Closed devices to the N.C. and C connectors on the Gateway, Reader, or Output module.

9PF—Power fail input: an unsupervised input that raises a “power fail” alarm when the circuit is open. Can be configured as an additional unsupervised port. An unsupervised input indicates only normal or alarm. The corresponding LED is red when circuit is open (when no input is connected).

10TM—Tamper input: an unsupervised input that raises a “tamper” alarm when the circuit is open. Can be configured as an additional unsupervised port. An unsupervised input indicates only normal or alarm. The corresponding LED is red when circuit is open (when no input is connected).

11Reset—Resets the device. See the “Resetting the Cisco Physical Access Gateway” section on page 2-24for more information.

LED Status

Table 2-1describes the Gateway module status LEDs:

Table 2-1

Gateway LEDs

Status

SVR

Description

Steady Green

The Gateway is connected to a Cisco PAM appliance.

Cisco Physical Access Gateway User Guide

 

OL-20932-02

2-5

 

 

 

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Americas Headquarters Cisco Physical Access Gateway User GuideCisco Physical Access Gateway User Guide N T E N T S Safety Warnings Environmental Specifications A-1 Contents Cisco Physical Access Gateway User Guide Preface Safety WarningsViii Overview System Overview Cisco Physical Access GatewayFeature Benefit Related Documentation Support for Multiple Cisco Physical Access GatewaysCisco Physical Access Manager Optional Expansion Modules 30VDC Module FeaturesCan Bus Connections for Optional Modules Installation and Configuration Summary Typical Wire Function Wires Gauge Type Use Door Device Wiring RequirementsUnderstanding Supervised and Unsupervised Input Devices Example of a Supervised Door Sensor Power Options Power Options and RequirementsModule Power over Ethernet PoE Through 24V DC Current Draw RequirementsConnect Reader Devices with Module Power Off Installing Surge Suppressors on Output Device ConnectionsWall Mounting a Gateway or Optional Module Mounting a Gateway or Optional ModuleWall Mount Installation Kit Contents OL-20932-02 Contents Overview Cisco Physical Access GatewayPhysical Overview and Port Description Package ContentsCisco Physical Access Gateway Ports and Connectors Top View Description LED StatusStatus Input Port LEDs Status DescriptionBefore You Begin Installing the Cisco Physical Access GatewayProcedure Power Connections for the Cisco Physical Access Gateway Chassis One Reader First Reader in a Label Description Wire ConnectionHcrd 271592 271593 CAN+ 271591 Understanding Network Time Protocol NTP Settings Connecting a PC to the Gateway 12 Login Screen for the Cisco Physical Access Gateway Entering the Gateway Network Settings13 Network Settings for the Cisco Physical Access Gateway Enter the Current Password Enter the New Password Changing the User Password15 Image Management for the Cisco Physical Access Gateway Upgrading the Gateway Firmware Using a Direct ConnectionOption 2 Remote Tftp Server Option 1 Local DiskDisplaying Serial Numbers and Other Information Installing and Configuring the Cisco Physical Access Gateway Hard Reset Restore Factory Defaults Resetting the Cisco Physical Access GatewaySoft Reset Powercycle Connecting a Cisco Reader Module Door Related Hardware Cisco Reader Module Ports and Connectors Cisco Reader Module Ports and Connectors Top View Cisco Physical Access Gateway User Guide OL-20932-02 Status LEDs Installing the Cisco Reader ModulePower Connection for the Cisco Reader Module 271600 +12v PWR red Output RED brown GRN orange 271592 271593 Connecting a Cisco Input Module Can connection Additional Connector plugs Cisco Input Module Ports and Connectors Top View Installing the Cisco Input Module Power Connections for the Input and Output Modules Can Connections Input and Output Modules 1K,, 1% Connecting a Cisco Output Module Connecting a Cisco Output Module Package Contents Cisco Output Module Ports and Connectors Cisco Output Module Ports and Connectors Top View Output Module LEDs Installing the Cisco Output Module Power Connections for the Cisco Output Module CAN+ Cisco Physical Access Gateway User Guide OL-20932-02 OL-20932-02 Statement 1071-Warning Definition Safety WarningsAvvertenza Importanti Istruzioni Sulla Sicurezza Warnung Wichtige SicherheitshinweiseGuarde Estas Instruções Aviso Instruções Importantes DE SegurançaGEM Disse Anvisninger Page Statement 369-Power over Ethernet PoE Ieee 802.3af Statement 353-This Product Must be Connected Appendix 6 Safety Warnings Statement 1040-Product Disposal Statement 1004-Installation Instructions Cisco Physical Access Gateway User Guide OL-20932-02 Gateway Environmental SpecificationsEnvironmental Specifications for the Cisco Input Module Environmental Specifications for the Cisco Reader ModuleEnvironmental Specifications for the Cisco Output Module OL-20932-02
Top Page Image Contents