Cisco Systems OL-20932-02 manual Entering the Gateway Network Settings

Page 41

Chapter 2 Installing and Configuring the Cisco Physical Access Gateway

Configuring and Managing the Gateway Using a Direct Connection

Figure 2-12 Login Screen for the Cisco Physical Access Gateway

The web administration pages appear, and are described in the following sections.

Entering the Gateway Network Settings

Enter the network settings to enable IP communication between the Gateway and the Cisco PAM appliance. Network settings include the following:

•ETH0 Configuration: the ETH0 port provides IP network connectivity with the Cisco PAM appliance.

•DNS Configuration: enter a DNS configuration if names (not IP addresses) are used for the NTP or CPAM addresses.

•Cisco PAM Configuration: defines the IP address and port of the Cisco PAM appliance that is used to manage the Gateway.

Tip Gateway modules can be added to the IP network before or after the full module configuration is entered in Cisco PAM. For more information, see the Cisco Physical Access Manager User Guide.

Procedure

Complete the following steps for each Gateway in the system.

Step 1 Enter the ETH0 Configuration settings, as shown in Figure 2-13. The ETH0 port is used for network communications with the Cisco PAM appliance.

a.If a Dynamic Host Configuration Protocol (DHCP) server is configured on your IP network, check the DHCP box for ETH0 to automatically configure the required IP network settings, including IP address, Subnet Mask, and Gateway. The DHCP check box is checked by default.

b.(Optional) If a DHCP server is not used to assign IP address settings, enter the following information in the ETH0 fields:

–IP address: Enter the IP address of the Cisco Physical Access Gateway.

–Subnet Mask: Enter the subnet mask.

–Gateway: Enter the IP gateway address.

		Cisco Physical Access Gateway User Guide
		Cisco Physical Access Gateway User Guide
	OL-20932-02			2-17
	OL-20932-02			2-17

Image 41

Contents Americas Headquarters Cisco Physical Access Gateway User GuideCisco Physical Access Gateway User Guide N T E N T S Safety Warnings Environmental Specifications A-1 Contents Cisco Physical Access Gateway User Guide Preface Safety WarningsViii Overview System Overview Cisco Physical Access GatewayFeature Benefit Related Documentation Support for Multiple Cisco Physical Access GatewaysCisco Physical Access Manager Optional Expansion Modules 30VDC Module FeaturesCan Bus Connections for Optional Modules Installation and Configuration Summary Typical Wire Function Wires Gauge Type Use Door Device Wiring RequirementsUnderstanding Supervised and Unsupervised Input Devices Example of a Supervised Door Sensor Power Options Power Options and RequirementsModule Power over Ethernet PoE Through 24V DC Current Draw RequirementsConnect Reader Devices with Module Power Off Installing Surge Suppressors on Output Device ConnectionsWall Mounting a Gateway or Optional Module Mounting a Gateway or Optional ModuleWall Mount Installation Kit Contents OL-20932-02 Contents Overview Cisco Physical Access GatewayPhysical Overview and Port Description Package ContentsCisco Physical Access Gateway Ports and Connectors Top View Description LED StatusStatus Input Port LEDs Status DescriptionBefore You Begin Installing the Cisco Physical Access GatewayProcedure Power Connections for the Cisco Physical Access Gateway Chassis One Reader First Reader in a Label Description Wire ConnectionHcrd 271592 271593 CAN+ 271591 Understanding Network Time Protocol NTP Settings Connecting a PC to the Gateway 12 Login Screen for the Cisco Physical Access Gateway Entering the Gateway Network Settings13 Network Settings for the Cisco Physical Access Gateway Enter the Current Password Enter the New Password Changing the User Password15 Image Management for the Cisco Physical Access Gateway Upgrading the Gateway Firmware Using a Direct ConnectionOption 2 Remote Tftp Server Option 1 Local DiskDisplaying Serial Numbers and Other Information Installing and Configuring the Cisco Physical Access Gateway Hard Reset Restore Factory Defaults Resetting the Cisco Physical Access GatewaySoft Reset Powercycle Connecting a Cisco Reader Module Door Related Hardware Cisco Reader Module Ports and Connectors Cisco Reader Module Ports and Connectors Top View Cisco Physical Access Gateway User Guide OL-20932-02 Status LEDs Installing the Cisco Reader ModulePower Connection for the Cisco Reader Module 271600 +12v PWR red Output RED brown GRN orange 271592 271593 Connecting a Cisco Input Module Can connection Additional Connector plugs Cisco Input Module Ports and Connectors Top View Installing the Cisco Input Module Power Connections for the Input and Output Modules Can Connections Input and Output Modules 1K,, 1% Connecting a Cisco Output Module Connecting a Cisco Output Module Package Contents Cisco Output Module Ports and Connectors Cisco Output Module Ports and Connectors Top View Output Module LEDs Installing the Cisco Output Module Power Connections for the Cisco Output Module CAN+ Cisco Physical Access Gateway User Guide OL-20932-02 OL-20932-02 Statement 1071-Warning Definition Safety WarningsAvvertenza Importanti Istruzioni Sulla Sicurezza Warnung Wichtige SicherheitshinweiseGuarde Estas Instruções Aviso Instruções Importantes DE SegurançaGEM Disse Anvisninger Page Statement 369-Power over Ethernet PoE Ieee 802.3af Statement 353-This Product Must be Connected Appendix 6 Safety Warnings Statement 1040-Product Disposal Statement 1004-Installation Instructions Cisco Physical Access Gateway User Guide OL-20932-02 Gateway Environmental SpecificationsEnvironmental Specifications for the Cisco Input Module Environmental Specifications for the Cisco Reader ModuleEnvironmental Specifications for the Cisco Output Module OL-20932-02