Billion Electric Company 5100S user manual Multiple PVC Permanent Virtual Circuits Support

Page 6

Using the standard TCP/IP protocol, the BIPAC 5100S and other UPnP enabled devices can dynamically join a network, obtain an IP address and convey its capabilities to other devices on the network.

10/100M Auto-negotiation Ethernet/Fast Ethernet Interface

This auto-negotiation feature allows the BIPAC 5100S to detect the speed of incoming transmissions and adjust appropriately without manual intervention. It allows data transfer of either 10 Mbps or 100 Mbps in either half-duplex or full-duplex mode depending on the Ethernet network.

Dynamic DNS Support

With Dynamic DNS support, you can have a static hostname alias for a dynamic IP address, allowing the host to be more easily accessible from various locations on the Internet. You must register for this service with a Dynamic DNS client.

Multiple PVC (Permanent Virtual Circuits) Support

The BIPAC 5100S supports up to 8 PVC’s.

ADSL Standards

♦Full-Rate (ANSI T1.413, Issue 2; G.dmt (G.992.1) with line rate support of up to 8 Mbps downstream and 1 Mbps upstream.

♦G.lite (G.992.2) with line rate support of up to 1.5Mbps downstream and 512Kbps upstream.

♦Supports Multi-Mode standard (ANSI T1.413, Issue 2; G.dmt (G.992.1); G.994.1 and G.996.1 (for ISDN only); G.991.1;G.lite (G992.2)).

♦Supports OAM F4/F5 loop-back, AIS and RDI OAM cells.

♦ATM Forum UNI 3.1/4.0 PVC.

♦Supports up to 8 PVCs (UBR, CBR, VBR).

♦Multiple Protocols over AAL5 (RFC 1483).

♦PPP over AAL5 (RFC 2364).

♦PPP over Ethernet (RFC 2516).

DHCP Support

DHCP (Dynamic Host Configuration Protocol) allows individual clients (computers) to obtain TCP/IP configuration at start-up from a centralized DHCP server. The BIPAC 5100S has built-in DHCP server capability enabled by default. It can assign IP addresses, an IP default gateway and DNS servers to DHCP clients. The BIPAC 5100S can now also act as a surrogate DHCP server (DHCP Relay) where it relays IP address assignment from the actual real DHCP server to the clients.

IP Alias

IP Alias allows you to partition a physical network into logical networks over the same Ethernet interface. The BIPAC 5100S supports three logical LAN interfaces via its single physical

6

Image 6

Contents Bipac 5100S Table of Contents LAN TCP/IP Appendix Features of the Bipac 5100S Getting to Know the Bipac 5100SIntroducing the Bipac 5100S Multiple PVC Permanent Virtual Circuits Support Multiplexing Applications for the Bipac 5100S Introducing the Web Configurator Web Configurator OverviewAccessing the Bipac 5100S Web Configurator Navigating the Bipac 5100S Web Configurator Configuring Password Resetting the Bipac 5100SUsing The Reset Button Encapsulation Wizard SetupWizard Setup Introduction PPP over EthernetMultiplexing Wizard Setup Configuration First Screen4 RFC VC-based MultiplexingIP Address and Subnet Mask Or PPPoEIP Assignment with RFC 1483 Encapsulation IP Address AssignmentIP Assignment with PPPoA or PPPoE Encapsulation IP Assignment with Enet Encap EncapsulationNailed-Up Connection PPP Wizard Setup Configuration Second ScreenPrivate IP Addresses NATPPPoE 10.2 RFC Enet Encap Exactly as given Dhcp Setup IP Pool SetupWizard Setup Configuration Third Screen Dhcp Wizard Setup Configuration Connection Tests Test Your Internet ConnectionLANs, WANs and the Bipac 5100S LAN SetupLAN Overview DNS Server AddressFactory LAN Defaults DNS Server Address AssignmentRIP Setup MulticastConfiguring LAN TCP/IP PPPoE Encapsulation WAN SetupWAN Overview Pptp EncapsulationConfiguring WAN Setup Traffic ShapingWhen to use Half Bridge mode PPP Half BridgeFollowing table describes the labels in this screen PPPoE Encap in the Encapsulation field NAT Definitions Network Address Translation NATNAT Overview What NAT DoesHow NAT Works NAT ApplicationNAT Mapping Types Type IP MappingPort Forwarding Services and Port Numbers SUA Single User Account Versus NATSUA Server Configuring Servers Behind SUA Example Services Port NumberSelecting the NAT Mode Configuring SUA ServerConfiguring Address Mapping Many-to-One and Server mapping types Editing an Address Mapping Rule NAT Address Mapping Rules screen Dynamic DNS Setup Dyndns Wildcard Configuring Dynamic DNSDynamic DNS Following table describes the labels in this screen Time and Date Setup Configuring Time ZonePage Remote Management Overview Remote Management ConfigurationSystem Timeout Remote Management LimitationsFTP Configuring Remote ManagementTelnet WebLabel Description Universal Plug and Play Overview How do I know if Im using UPnP?Universal Plug-and-Play UPnP NAT TraversalConfiguring UPnP Installing UPnP in Windows ExampleInstalling UPnP in Windows Me Installing UPnP in Windows XP Page Using UPnP in Windows XP Example Auto-discover Your UPnP-enabled Network DeviceWeb Configurator Easy Access Page Maintenance Maintenance OverviewSystem Status Screen Following table describes the labels in this screen System Statistics Dhcp Table Screen Diagnostic Screens Diagnostic General ScreenDiagnostic DSL Line Screen Reset Adsl Line Firmware Screen Page Troubleshooting Using LEDs to Diagnose ProblemsPower LED Web Configurator Cannot telnet into the Bipac 5100SLogin Username and Password LAN InterfaceWAN Interface Internet Access Remote ManagementRemote Node Connection Cannot connect to a remote node or ISP