Billion Electric Company 5100S user manual Dhcp Table Screen

Page 62

CPU Load

This field specifies the percentage of CPU utilization.

 

 

WAN Port Statistics

This is the WAN port.

 

 

Link Status

This is the status of your WAN link.

 

 

Transfer Rate

This is the transfer rate in kbps.

 

 

Upstream Speed

This is the upstream speed of your BIPAC 5100S.

 

 

Downstream Speed

This is the downstream speed of your BIPAC 5100S.

 

 

Node-Link

This field displays the remote node index number and link type. Link types are

 

PPPoA, ENET, RFC 1483 and PPPoE.

 

 

LAN Port Statistics

This is the LAN port.

 

 

Interface

This field displays the type of port.

 

 

Status

For the WAN port, this displays the port speed and duplex setting if you're using

 

Ethernet encapsulation and down (line is down), idle (line (ppp) idle), dial (starting

 

to trigger a call) and drop (dropping a call) if you're using PPPoE encapsulation.

 

For a LAN port, this shows the port speed and duplex setting.

 

 

TxPkts

This field displays the number of packets transmitted on this port.

 

 

RxPkts

This field displays the number of packets received on this port.

 

 

Errors

This field displays the number of error packets on this port.

 

 

Tx B/s

This field displays the number of bytes transmitted in the last second.

 

 

Rx B/s

This field displays the number of bytes received in the last second.

 

 

Up Time

This field displays the elapsed time this port has been up.

 

 

Collisions

This is the number of collisions on this port.

 

 

Poll Interval(s)

Type the time interval for the browser to refresh system statistics.

 

 

Set Interval

Click this button to apply the new poll interval you entered in the Poll Interval field

 

above.

 

 

Stop

Click this button to halt the refreshing of the system statistics.

 

 

11.3 DHCP Table Screen

DHCP (Dynamic Host Configuration Protocol, RFC 2131 and RFC 2132) allows individual clients to obtain TCP/IP configuration at start-up from a server. You can configure the BIPAC 5100S as a DHCP server or disable it. When configured as a server, the BIPAC 5100S provides the TCP/IP configuration for the clients. If set to None, DHCP service will be disabled and you must have another DHCP server on your LAN, or else the computer must be manually configured.

Click MAINTENANCE, and then the DHCP Table tab. Read-only information here relates to your DHCP status. The DHCP table shows current DHCP client information (including IP Address, Host Name and MAC Address) of all network clients using the DHCP server.

62

Image 62
Contents Bipac 5100S Table of Contents LAN TCP/IP Appendix Introducing the Bipac 5100S Features of the Bipac 5100SGetting to Know the Bipac 5100S Multiple PVC Permanent Virtual Circuits Support Multiplexing Applications for the Bipac 5100S Accessing the Bipac 5100S Web Configurator Introducing the Web ConfiguratorWeb Configurator Overview Navigating the Bipac 5100S Web Configurator Using The Reset Button Configuring PasswordResetting the Bipac 5100S Encapsulation Wizard SetupWizard Setup Introduction PPP over EthernetMultiplexing Wizard Setup Configuration First Screen4 RFC VC-based MultiplexingIP Address and Subnet Mask Or PPPoEIP Assignment with RFC 1483 Encapsulation IP Address AssignmentIP Assignment with PPPoA or PPPoE Encapsulation IP Assignment with Enet Encap EncapsulationNailed-Up Connection PPP Wizard Setup Configuration Second ScreenPrivate IP Addresses NATPPPoE 10.2 RFC Enet Encap Exactly as given Wizard Setup Configuration Third Screen Dhcp SetupIP Pool Setup Dhcp Wizard Setup Configuration Connection Tests Test Your Internet ConnectionLANs, WANs and the Bipac 5100S LAN SetupLAN Overview DNS Server AddressFactory LAN Defaults DNS Server Address AssignmentRIP Setup MulticastConfiguring LAN TCP/IP PPPoE Encapsulation WAN SetupWAN Overview Pptp EncapsulationConfiguring WAN Setup Traffic ShapingWhen to use Half Bridge mode PPP Half BridgeFollowing table describes the labels in this screen PPPoE Encap in the Encapsulation field NAT Definitions Network Address Translation NATNAT Overview What NAT DoesHow NAT Works NAT ApplicationNAT Mapping Types Type IP MappingSUA Server Port Forwarding Services and Port NumbersSUA Single User Account Versus NAT Configuring Servers Behind SUA Example Services Port NumberSelecting the NAT Mode Configuring SUA ServerConfiguring Address Mapping Many-to-One and Server mapping types Editing an Address Mapping Rule NAT Address Mapping Rules screen Dynamic DNS Dynamic DNS SetupDyndns Wildcard Configuring Dynamic DNS Following table describes the labels in this screen Time and Date Setup Configuring Time ZonePage Remote Management Overview Remote Management ConfigurationSystem Timeout Remote Management LimitationsFTP Configuring Remote ManagementTelnet WebLabel Description Universal Plug and Play Overview How do I know if Im using UPnP?Universal Plug-and-Play UPnP NAT TraversalInstalling UPnP in Windows Me Configuring UPnPInstalling UPnP in Windows Example Installing UPnP in Windows XP Page Using UPnP in Windows XP Example Auto-discover Your UPnP-enabled Network DeviceWeb Configurator Easy Access Page System Status Screen MaintenanceMaintenance Overview Following table describes the labels in this screen System Statistics Dhcp Table Screen Diagnostic Screens Diagnostic General ScreenDiagnostic DSL Line Screen Reset Adsl Line Firmware Screen Page Power LED TroubleshootingUsing LEDs to Diagnose Problems Web Configurator Cannot telnet into the Bipac 5100SWAN Interface Login Username and PasswordLAN Interface Internet Access Remote ManagementRemote Node Connection Cannot connect to a remote node or ISP