Billion Electric Company user manual Web Configurator, Cannot telnet into the Bipac 5100S

Page 69

3Reset your ADSL line to reinitialize your link to the DSLAM. For details, refer to the Maintenance chapter (web configurator) or the System Information and Diagnosis chapter.

4If these steps fail to correct the problem, contact your local distributor for assistance.

A.2 Telnet

I cannot telnet into the BIPAC 5100S.

STEPS

CORRECTIVE ACTION

 

 

1

Check the LAN port and the other Ethernet connections.

 

 

2

Make sure you are using the correct IP address of the BIPAC 5100S. Check the IP

 

address of the BIPAC 5100S.

 

 

3

Ping the BIPAC 5100S from your computer.

 

If you cannot ping the BIPAC 5100S, check the IP addresses of the BIPAC 5100S and

 

your computer. Make sure your computer is set to get a dynamic IP address; or if you

 

want to use a static IP address on your computer, make sure that it is on the same

 

subnet as the BIPAC 5100S.

 

 

4

Make sure you entered the correct password. The default password is “admin”.

 

If you have forgot your username or password, refer to Section A.5.

 

 

5

If these steps fail to correct the problem, contact the distributor.

 

 

A.3 Web Configurator

I cannot access the web configurator.

STEPS

CORRECTIVE ACTION

 

 

1

Make sure you are using the correct IP address of the BIPAC 5100S. Check the IP

 

address of the BIPAC 5100S.

 

 

2

Check that you have enabled web service access. If you have configured a secured

 

client IP address, your computer’s IP address must match it. Refer to the chapter on

 

remote management for details.

 

 

3

For WAN access, you must configure remote management to allow server access from

 

the Wan (or all).

 

 

4

Your computer’s and the BIPAC 5100S’s IP addresses must be on the same subnet for

 

LAN access.

 

 

5

If you changed the BIPAC 5100S’s LAN IP address, then enter the new one as the URL.

 

 

6

Remove any filters in LAN or WAN that block web service.

 

 

7

See also Section A.9.

 

 

The web configurator does not display properly.

69

Image 69
Contents Bipac 5100S Table of Contents LAN TCP/IP Appendix Features of the Bipac 5100S Getting to Know the Bipac 5100SIntroducing the Bipac 5100S Multiple PVC Permanent Virtual Circuits Support Multiplexing Applications for the Bipac 5100S Introducing the Web Configurator Web Configurator OverviewAccessing the Bipac 5100S Web Configurator Navigating the Bipac 5100S Web Configurator Configuring Password Resetting the Bipac 5100SUsing The Reset Button Wizard Setup Introduction Wizard SetupEncapsulation PPP over Ethernet4 RFC Wizard Setup Configuration First ScreenMultiplexing VC-based MultiplexingOr PPPoE IP Address and Subnet MaskIP Assignment with PPPoA or PPPoE Encapsulation IP Address AssignmentIP Assignment with RFC 1483 Encapsulation IP Assignment with Enet Encap EncapsulationPrivate IP Addresses Wizard Setup Configuration Second ScreenNailed-Up Connection PPP NATPPPoE 10.2 RFC Enet Encap Exactly as given Dhcp Setup IP Pool SetupWizard Setup Configuration Third Screen Dhcp Test Your Internet Connection Wizard Setup Configuration Connection TestsLAN Overview LAN SetupLANs, WANs and the Bipac 5100S DNS Server AddressDNS Server Address Assignment Factory LAN DefaultsMulticast RIP SetupConfiguring LAN TCP/IP WAN Overview WAN SetupPPPoE Encapsulation Pptp EncapsulationTraffic Shaping Configuring WAN SetupPPP Half Bridge When to use Half Bridge modeFollowing table describes the labels in this screen PPPoE Encap in the Encapsulation field NAT Overview Network Address Translation NATNAT Definitions What NAT DoesNAT Application How NAT WorksType IP Mapping NAT Mapping TypesPort Forwarding Services and Port Numbers SUA Single User Account Versus NATSUA Server Services Port Number Configuring Servers Behind SUA ExampleConfiguring SUA Server Selecting the NAT ModeConfiguring Address Mapping Many-to-One and Server mapping types Editing an Address Mapping Rule NAT Address Mapping Rules screen Dynamic DNS Setup Dyndns Wildcard Configuring Dynamic DNSDynamic DNS Following table describes the labels in this screen Configuring Time Zone Time and Date SetupPage System Timeout Remote Management ConfigurationRemote Management Overview Remote Management LimitationsTelnet Configuring Remote ManagementFTP WebLabel Description Universal Plug-and-Play UPnP How do I know if Im using UPnP?Universal Plug and Play Overview NAT TraversalConfiguring UPnP Installing UPnP in Windows ExampleInstalling UPnP in Windows Me Installing UPnP in Windows XP Page Auto-discover Your UPnP-enabled Network Device Using UPnP in Windows XP ExampleWeb Configurator Easy Access Page Maintenance Maintenance OverviewSystem Status Screen Following table describes the labels in this screen System Statistics Dhcp Table Screen Diagnostic General Screen Diagnostic ScreensDiagnostic DSL Line Screen Reset Adsl Line Firmware Screen Page Troubleshooting Using LEDs to Diagnose ProblemsPower LED Cannot telnet into the Bipac 5100S Web ConfiguratorLogin Username and Password LAN InterfaceWAN Interface Remote Management Internet AccessCannot connect to a remote node or ISP Remote Node Connection