Cisco Systems WRV54G manual MAC Address Clone Tab See Figure, Advanced Routing Tab, MAC Clone

Page 28

Wireless-G VPN Broadband Router

MAC Address Clone Tab (See Figure 6-8.)

The Router’s MAC address is a 12-digit code assigned to a unique piece of hardware for identification, like a social security number. If your ISP requires MAC address registration, find your adapter’s MAC address by following the instructions in “Appendix D: Finding the MAC Address and IP Address for Your Ethernet Adapter.”

MAC Clone

•MAC Clone Service. To use MAC address cloning, select Enable.

•MAC Address. To manually clone a MAC address, enter the 12 digits of your adapter’s MAC address in the on- screen fields (see Figure 6-8). Then click the Save Settings button.

•Clone My MAC Address. If you want to clone the MAC address of the PC you are currently using to configure the Router, then click the Clone My MAC Address button. The Router will automatically detect your PC’s MAC address, so you do NOT have to call your ISP to change the registered MAC address to the Router’s MAC address. It is recommended that the PC registered with the ISP is used to open the MAC Address Clone tab.

When finished making your changes on this tab, click the Save Settings button to save these changes, or click the Cancel Changes button to undo your changes.

Advanced Routing Tab

The Advanced Routing screen allows you to configure the dynamic routing and static routing settings. (See Figure 6-9.)

Advanced Routing

•Operating Mode. Select Gateway or Router for the Operating Mode from the drop-down menu.

•Dynamic Routing. With Dynamic Routing you can enable the Router to automatically adjust to physical changes in the network’s layout. The Router, using the RIP protocol, determines the network packets’ route based on the fewest number of hops between the source and the destination. The RIP protocol regularly broadcasts routing information to other routers on the network.

•Receive RIP Version To use dynamic routing for reception of network data, select the protocol you want: RIP1 or RIP2.

•Transmit RIP Version. To use dynamic routing for transmission of network data, select the protocol you want: RIP1, RIP1-Compatible, or RIP2.

Chapter 6: Configuring the Router

Figure 6-8: MAC Address Clone

Figure 6-9: Advanced Routing

24

The Setup Tab

Image 28

Contents 802 GHz .11g Wireless- G Copyright and Trademarks How to Use this GuideWord definition Table of Contents Wireless Security Frequently Asked QuestionsIntroduction WelcomeWhat’s in this Guide? Wireless-G Broadband VPN Router Planning your Wireless Network Router’s FunctionsIP Addresses What’s an IP Address?Dhcp Dynamic Host Configuration Protocol Servers Why do I need a VPN?Dynamic IP Addresses What is a VPN? VPN Router to VPN Router Wireless-G VPN Broadband Router Getting to Know the Wireless-G VPN Broadband Router Back PanelFront Panel DMZConnecting the Wireless-G Broadband Router OverviewWired Connection to a PC Wireless Connection to a PCWireless-G VPN Broadband Router Configuring the PCs Configuring Windows 98 and Millennium PCsConfiguring Windows 2000 PCs PropertiesConfiguring Windows XP PCs Setup Configuring the RouterWireless Access Restrictions AdministrationSecurity Applications & GamingHow to Access the Web-based Utility Setup TabBasic Setup Tab Internet SetupStatic Internet Connection Type Optional Settings Required by some ISPs Pptp Internet Connection TypeNetwork Setup Ddns Tab DynDNS.orgMAC Address Clone Tab See Figure Advanced Routing TabMAC Clone Advanced RoutingStatic Routing 10 Routing TableBasic Wireless Settings See Figure Wireless TabWireless Network Wireless Security WEP See FigureWireless Network Access See Figure 13 Wireless Network AccessAdvanced Wireless Settings See Figure 15 Advanced Wireless SettingsSecurity Tab FirewallVPN 18 Manual Key Management 19 Advanced VPN Tunnel Setup WEP Access Restrictions Tab Access Restriction23 Internet Filter Summary Applications and Gaming Tab Port Range ForwardingPort Triggering 27 Port TriggeringUPnP Forwarding 28 UPnP ForwardingDMZ Router Password Administration TabManagement Log UPnPEmail Alert Syslog NotificationDiagnostics Notification Queue LengthAlert Log General Log33 Factory Default Status RouterInformation WAN ConnectionsLocal Network 36 Local Network38 Wireless System PerformanceCommon Problems and Solutions Appendix a TroubleshootingNeed to set a static IP address on a PC Wireless-G VPN Broadband Router Wireless-G VPN Broadband Router Wireless-G VPN Broadband Router TCP UDP Can’t get the Internet game, server, or application to work Need to upgrade the firmware To start over, I need to set the Router to factory defaultFirmware upgrade failed, and/or the Power LED is flashing My DSL service’s PPPoE is always disconnecting Power LED flashes continuouslyFrequently Asked Questions Where is the Router installed on the network?Is IPSec Pass-Through supported by the Router? Does the Router support IPX or AppleTalk?What is Network Address Translation and what is it used for? Does the Router support ICQ send file?How can I block corrupted FTP downloads? What is DMZ Hosting? What are the advanced features of the Router?Is the Router cross-platform compatible? How many ports can be simultaneously forwarded?What is the Ieee 802.11g standard? What Ieee 802.11b features are supported?What is ad-hoc mode? What is infrastructure mode?What is ISM band? What is Spread Spectrum?What is DSSS? What is FHSS? And what are their differences? What is WEP?How do I resolve issues with signal loss? How do I reset the Router?Have excellent signal strength, but I cannot see my network Brief Overview Appendix B Wireless SecurityWhat Are The Risks? Passive Attacks Jamming AttacksMaximizing Wireless Security Active AttacksDictionary-Building or Table Attacks Man-in-the-Middle Attacks5SSID 8WEP Wireless-G VPN Broadband Router 4GHz/802.11b and 802.11g WEP Encryption Figure B-2 WEPEnvironment WRV54GHow to Establish a Secure IPSec Tunnel Create an IPSec PolicyBuild Filter Lists Filter List 1 win-routerFilter List 2 router-win Figure C-4 IP Filter ListFigure C-7 IP Filter List Configure Individual Tunnel Rules Tunnel 1 win-routerFigure C-13 Authentication Methods Figure C-16 Tunnel Setting Tab Tunnel 2 router-winFigure C-19 IP Filter List Tab Figure C-22 Preshared Key Assign New IPSec Policy Figure C-25 Connection TypeCreate a Tunnel Through the Web-Based Utility Figure C-28 VPN TabFigure D-1 IP Configuration Screen Windows 98 or Me InstructionsWindows 2000 or XP Instructions Figure D-3 MAC Address/Physical AddressAppendix E Snmp Functions Figure F-1 Upgrade Firmware Appendix F Upgrading FirmwareShared Resources Appendix G Windows HelpNetwork Neighborhood/My Network Places Appendix H Glossary Wireless-G VPN Broadband Router Wireless-G VPN Broadband Router Wireless-G VPN Broadband Router Wireless-G VPN Broadband Router Wireless-G VPN Broadband Router Transmit Power 19dBm LEDs Appendix I SpecificationsUp to 54Mbps wireless, up to 100 Mbps LAN Appendix J Regulatory Information FCC StatementFCC Part 68 Statement Safety Notices Appendix K Warranty Information Limited WarrantyAppendix L Contact Information