Cisco Systems WRV54G manual Static Routing, Routing Table

Page 29

Wireless-G VPN Broadband Router

Static Routing

If the Router is connected to more than one network, it may be necessary to set up a static route between them. A static route is a pre-determined pathway that network information must travel to reach a specific host or network. To create a static route, change the following settings:

•Select Number. Select the number of the static route from the drop-down menu. The Router supports up to 20 static route entries.

•Delete This Entry. If you need to delete a route, select its number from the drop-down menu, and click the Delete Entry button.

•LAN IP Address. The LAN IP Address is the address of the remote network or host to which you want to assign a static route. Enter the IP address of the host for which you wish to create a static route. If you are building a route to an entire network, be sure that the network portion of the IP address is set to 0. For example, the Router’s standard IP address is 192.168.1.1. Based on this address, the address of the routed network is 192.168.1, with the last digit determining the Router’s place on the network. Therefore you would enter the IP address 192.168.1.0 if you wanted to route to the Router’s entire network, rather than just to the Router.

•Subnet Mask. The Subnet Mask (also known as the Network Mask) determines which portion of an IP address is the network portion, and which portion is the host portion. Take, for example, a network in which the Subnet Mask is 255.255.255.0. This determines (by using the values 255) that the first three numbers of a network IP address identify this particular network, while the last digit (from 1 to 254) identifies the specific host.

•Default Gateway. This IP address should be the IP address of the gateway device that allows for contact between the Router and the remote network or host.

•metric. This determines the maximum number of steps between network nodes that data packets will travel. A node is any device on the network, such as PCs, print servers, routers, etc.

•Interface. Select LAN & Wireless or Internet, depending on the location of the static route’s final destination.

•Show Routing Table. Click the Show Routing Table button to open a screen displaying how data is routed through your LAN. For each route, the Destination LAN IP address, Subnet Mask, Default Gateway, and Interface are displayed. Click the Refresh button to update the information. See Figure 6-10.

When finished making your changes on this tab, click the Save Settings button to save these changes, or click the Cancel Changes button to undo your changes.

Chapter 6: Configuring the Router

Figure 6-10: Routing Table

25

The Setup Tab

Page 28 Page 30
Image 29
Page 28 Page 30
Contents 802 GHz .11g Wireless- G Word definition How to Use this GuideCopyright and Trademarks Table of Contents Frequently Asked Questions Wireless SecurityWelcome IntroductionWhat’s in this Guide? Wireless-G Broadband VPN Router Router’s Functions Planning your Wireless NetworkIP Addresses What’s an IP Address?Dynamic IP Addresses Why do I need a VPN?Dhcp Dynamic Host Configuration Protocol Servers What is a VPN? VPN Router to VPN Router Wireless-G VPN Broadband Router Back Panel Getting to Know the Wireless-G VPN Broadband RouterDMZ Front PanelOverview Connecting the Wireless-G Broadband RouterWireless Connection to a PC Wired Connection to a PCWireless-G VPN Broadband Router Configuring Windows 98 and Millennium PCs Configuring the PCsProperties Configuring Windows 2000 PCsConfiguring Windows XP PCs Wireless Configuring the RouterSetup Administration Access RestrictionsSecurity Applications & GamingSetup Tab How to Access the Web-based UtilityBasic Setup Tab Internet SetupStatic Internet Connection Type Pptp Internet Connection Type Optional Settings Required by some ISPsNetwork Setup DynDNS.org Ddns TabAdvanced Routing Tab MAC Address Clone Tab See FigureMAC Clone Advanced Routing10 Routing Table Static RoutingWireless Network Wireless TabBasic Wireless Settings See Figure WEP See Figure Wireless Security13 Wireless Network Access Wireless Network Access See Figure15 Advanced Wireless Settings Advanced Wireless Settings See FigureFirewall Security TabVPN 18 Manual Key Management 19 Advanced VPN Tunnel Setup WEP Access Restriction Access Restrictions Tab23 Internet Filter Summary Port Range Forwarding Applications and Gaming Tab27 Port Triggering Port Triggering28 UPnP Forwarding UPnP ForwardingDMZ Management Administration TabRouter Password UPnP LogEmail Alert Syslog NotificationNotification Queue Length DiagnosticsAlert Log General Log33 Factory Default Router StatusInformation WAN Connections36 Local Network Local NetworkSystem Performance 38 WirelessNeed to set a static IP address on a PC Appendix a TroubleshootingCommon Problems and Solutions Wireless-G VPN Broadband Router Wireless-G VPN Broadband Router Wireless-G VPN Broadband Router TCP UDP Can’t get the Internet game, server, or application to work Firmware upgrade failed, and/or the Power LED is flashing To start over, I need to set the Router to factory defaultNeed to upgrade the firmware Power LED flashes continuously My DSL service’s PPPoE is always disconnectingWhere is the Router installed on the network? Frequently Asked QuestionsIs IPSec Pass-Through supported by the Router? Does the Router support IPX or AppleTalk?Does the Router support ICQ send file? What is Network Address Translation and what is it used for?How can I block corrupted FTP downloads? What are the advanced features of the Router? What is DMZ Hosting?Is the Router cross-platform compatible? How many ports can be simultaneously forwarded?What Ieee 802.11b features are supported? What is the Ieee 802.11g standard?What is ad-hoc mode? What is infrastructure mode?What is Spread Spectrum? What is ISM band?What is DSSS? What is FHSS? And what are their differences? What is WEP?Have excellent signal strength, but I cannot see my network How do I reset the Router?How do I resolve issues with signal loss? What Are The Risks? Appendix B Wireless SecurityBrief Overview Jamming Attacks Passive AttacksActive Attacks Maximizing Wireless SecurityDictionary-Building or Table Attacks Man-in-the-Middle Attacks5SSID 8WEP Wireless-G VPN Broadband Router Figure B-2 WEP 4GHz/802.11b and 802.11g WEP EncryptionWRV54G EnvironmentCreate an IPSec Policy How to Establish a Secure IPSec TunnelBuild Filter Lists Filter List 1 win-routerFigure C-4 IP Filter List Filter List 2 router-winFigure C-7 IP Filter List Tunnel 1 win-router Configure Individual Tunnel RulesFigure C-13 Authentication Methods Tunnel 2 router-win Figure C-16 Tunnel Setting TabFigure C-19 IP Filter List Tab Figure C-22 Preshared Key Figure C-25 Connection Type Assign New IPSec PolicyFigure C-28 VPN Tab Create a Tunnel Through the Web-Based UtilityWindows 98 or Me Instructions Figure D-1 IP Configuration ScreenFigure D-3 MAC Address/Physical Address Windows 2000 or XP InstructionsAppendix E Snmp Functions Appendix F Upgrading Firmware Figure F-1 Upgrade FirmwareNetwork Neighborhood/My Network Places Appendix G Windows HelpShared Resources Appendix H Glossary Wireless-G VPN Broadband Router Wireless-G VPN Broadband Router Wireless-G VPN Broadband Router Wireless-G VPN Broadband Router Wireless-G VPN Broadband Router Up to 54Mbps wireless, up to 100 Mbps LAN Appendix I SpecificationsTransmit Power 19dBm LEDs FCC Statement Appendix J Regulatory InformationFCC Part 68 Statement Safety Notices Limited Warranty Appendix K Warranty InformationAppendix L Contact Information
Top Page Image Contents