Cisco Systems WRV54G Frequently Asked Questions, Is IPSec Pass-Through supported by the Router?

Page 60

Wireless-G VPN Broadband Router

flash the firmware by assigning a static IP address to the computer, and then upgrade the firmware. Try using the following settings, IP Address: 192.168.1.50 and Subnet Mask: 255.255.255.0.

17.When I enter a URL or IP address, I get a time-out error or am prompted to retry.

•Check if other PCs work. If they do, ensure that your workstation’s IP settings are correct (IP Address, Subnet Mask, Default Gateway, and DNS). Restart the computer that is having a problem.

•If the PCs are configured correctly, but still not working, check the Router. Ensure that it is connected and powered on. Connect to it and check its settings. (If you cannot connect to it, check the LAN and power connections.)

•If the Router is configured correctly, check your Internet connection (DSL/cable modem, etc.) to see if it is working correctly. You can remove the Router to verify a direct connection.

•Manually configure the TCP/IP settings with a DNS address provided by your ISP.

•Make sure that your browser is set to connect directly and that any dial-up is disabled. For Internet Explorer, click Tools, Internet Options, and then the Connection tab. Make sure that Internet Explorer is set to Never dial a connection. For Netscape Navigator, click Edit, Preferences, Advanced, and Proxy. Make sure that Netscape Navigator is set to Direct connection to the Internet.

Frequently Asked Questions

What is the maximum number of IP addresses that the Router will support?

The Router will support up to 253 IP addresses.

Is IPSec Pass-Through supported by the Router?

Yes, it is a built-in feature that the Router automatically enables.

Where is the Router installed on the network?

In a typical environment, the Router is installed between the cable/DSL modem and the LAN. Plug the Router into the cable/DSL modem’s Ethernet port.

Does the Router support IPX or AppleTalk?

No. TCP/IP is the only protocol standard for the Internet and has become the global standard for communications. IPX, a NetWare communications protocol used only to route messages from one node to another, and AppleTalk, a communications protocol used on Apple and Macintosh networks, can be used for LAN to LAN connections, but those protocols cannot connect from the Internet to a LAN.

Appendix A: Troubleshooting

56

Frequently Asked Questions

Image 60

Contents 802 GHz .11g Wireless- G How to Use this Guide Copyright and TrademarksWord definition Table of Contents Wireless Security Frequently Asked QuestionsIntroduction WelcomeWhat’s in this Guide? Wireless-G Broadband VPN Router Planning your Wireless Network Router’s FunctionsIP Addresses What’s an IP Address?Why do I need a VPN? Dhcp Dynamic Host Configuration Protocol ServersDynamic IP Addresses What is a VPN? VPN Router to VPN Router Wireless-G VPN Broadband Router Getting to Know the Wireless-G VPN Broadband Router Back PanelFront Panel DMZConnecting the Wireless-G Broadband Router OverviewWired Connection to a PC Wireless Connection to a PCWireless-G VPN Broadband Router Configuring the PCs Configuring Windows 98 and Millennium PCsConfiguring Windows 2000 PCs PropertiesConfiguring Windows XP PCs Configuring the Router SetupWireless Access Restrictions AdministrationSecurity Applications & GamingHow to Access the Web-based Utility Setup TabBasic Setup Tab Internet SetupStatic Internet Connection Type Optional Settings Required by some ISPs Pptp Internet Connection TypeNetwork Setup Ddns Tab DynDNS.orgMAC Address Clone Tab See Figure Advanced Routing TabMAC Clone Advanced RoutingStatic Routing 10 Routing TableWireless Tab Basic Wireless Settings See FigureWireless Network Wireless Security WEP See FigureWireless Network Access See Figure 13 Wireless Network AccessAdvanced Wireless Settings See Figure 15 Advanced Wireless SettingsSecurity Tab FirewallVPN 18 Manual Key Management 19 Advanced VPN Tunnel Setup WEP Access Restrictions Tab Access Restriction23 Internet Filter Summary Applications and Gaming Tab Port Range ForwardingPort Triggering 27 Port TriggeringUPnP Forwarding 28 UPnP ForwardingDMZ Administration Tab Router PasswordManagement Log UPnPEmail Alert Syslog NotificationDiagnostics Notification Queue LengthAlert Log General Log33 Factory Default Status RouterInformation WAN ConnectionsLocal Network 36 Local Network38 Wireless System PerformanceAppendix a Troubleshooting Common Problems and SolutionsNeed to set a static IP address on a PC Wireless-G VPN Broadband Router Wireless-G VPN Broadband Router Wireless-G VPN Broadband Router TCP UDP Can’t get the Internet game, server, or application to work To start over, I need to set the Router to factory default Need to upgrade the firmwareFirmware upgrade failed, and/or the Power LED is flashing My DSL service’s PPPoE is always disconnecting Power LED flashes continuouslyFrequently Asked Questions Where is the Router installed on the network?Is IPSec Pass-Through supported by the Router? Does the Router support IPX or AppleTalk?What is Network Address Translation and what is it used for? Does the Router support ICQ send file?How can I block corrupted FTP downloads? What is DMZ Hosting? What are the advanced features of the Router?Is the Router cross-platform compatible? How many ports can be simultaneously forwarded?What is the Ieee 802.11g standard? What Ieee 802.11b features are supported?What is ad-hoc mode? What is infrastructure mode?What is ISM band? What is Spread Spectrum?What is DSSS? What is FHSS? And what are their differences? What is WEP?How do I reset the Router? How do I resolve issues with signal loss?Have excellent signal strength, but I cannot see my network Appendix B Wireless Security Brief OverviewWhat Are The Risks? Passive Attacks Jamming AttacksMaximizing Wireless Security Active AttacksDictionary-Building or Table Attacks Man-in-the-Middle Attacks5SSID 8WEP Wireless-G VPN Broadband Router 4GHz/802.11b and 802.11g WEP Encryption Figure B-2 WEPEnvironment WRV54GHow to Establish a Secure IPSec Tunnel Create an IPSec PolicyBuild Filter Lists Filter List 1 win-routerFilter List 2 router-win Figure C-4 IP Filter ListFigure C-7 IP Filter List Configure Individual Tunnel Rules Tunnel 1 win-routerFigure C-13 Authentication Methods Figure C-16 Tunnel Setting Tab Tunnel 2 router-winFigure C-19 IP Filter List Tab Figure C-22 Preshared Key Assign New IPSec Policy Figure C-25 Connection TypeCreate a Tunnel Through the Web-Based Utility Figure C-28 VPN TabFigure D-1 IP Configuration Screen Windows 98 or Me InstructionsWindows 2000 or XP Instructions Figure D-3 MAC Address/Physical AddressAppendix E Snmp Functions Figure F-1 Upgrade Firmware Appendix F Upgrading FirmwareAppendix G Windows Help Shared ResourcesNetwork Neighborhood/My Network Places Appendix H Glossary Wireless-G VPN Broadband Router Wireless-G VPN Broadband Router Wireless-G VPN Broadband Router Wireless-G VPN Broadband Router Wireless-G VPN Broadband Router Appendix I Specifications Transmit Power 19dBm LEDsUp to 54Mbps wireless, up to 100 Mbps LAN Appendix J Regulatory Information FCC StatementFCC Part 68 Statement Safety Notices Appendix K Warranty Information Limited WarrantyAppendix L Contact Information