Cisco Systems WRV54G manual To start over, I need to set the Router to factory default

Page 58

Wireless-G VPN Broadband Router

10.I am a PPPoE user, and I need to remove the proxy settings or the dial-up pop-up window.

If you have proxy settings, you need to disable these on your computer. Because the Router is the gateway for the Internet connection, the computer does not need any proxy settings to gain access. Please follow these directions to verify that you do not have any proxy settings and that the browser you use is set to connect directly to the LAN.

•For Microsoft Internet Explorer 5.0 or higher:

1.Click Start, Settings, and Control Panel. Double-click Internet Options.

2.Click the Connections tab.

3.Click the LAN settings button and remove anything that is checked.

4.Click the OK button to go back to the previous screen.

5.Click the option Never dial a connection. This will remove any dial-up pop-ups for PPPoE users.

•For Netscape 4.7 or higher:

1.Start Netscape Navigator, and click Edit, Preferences, Advanced, and Proxies.

2.Make sure you have Direct connection to the Internet selected on this screen.

3.Close all the windows to finish.

11.To start over, I need to set the Router to factory default.

Hold the Reset button for 10 seconds and then release it. This will return the password, forwarding, and other settings on the Router to the factory default settings. In other words, the Router will revert to its original factory configuration.

12.I need to upgrade the firmware.

In order to upgrade the firmware with the latest features, you need to go to the Linksys website and download the latest firmware at www.linksys.com.

•Follow these steps:

1.Go to the Linksys website at http://www.linksys.com and download the latest firmware.

2.To upgrade the firmware, follow the steps in the System section found in “Chapter 6: The Router’s Web-based Utility.”

13.The firmware upgrade failed, and/or the Power LED is flashing.

The upgrade could have failed for a number of reasons. Follow these steps to upgrade the firmware and/or make the Power LED stop flashing:

•If the firmware upgrade failed, use the TFTP program (it was downloaded along with the firmware). Open the pdf that was downloaded along with the firmware and TFTP program, and follow the pdf’s instructions.

•Set a static IP address on the PC; refer to “Problem #1, I need to set a static IP address.” Use the following IP address settings for the computer you are using:

IP Address: 192.168.1.50

Subnet Mask: 255.255.255.0

Appendix A: Troubleshooting

54

Common Problems and Solutions

Page 57 Page 59
Image 58
Page 57 Page 59
Contents 802 GHz .11g Wireless- G Copyright and Trademarks How to Use this GuideWord definition Table of Contents Wireless Security Frequently Asked QuestionsIntroduction WelcomeWhat’s in this Guide? Wireless-G Broadband VPN Router IP Addresses Planning your Wireless NetworkRouter’s Functions What’s an IP Address?Dhcp Dynamic Host Configuration Protocol Servers Why do I need a VPN?Dynamic IP Addresses What is a VPN? VPN Router to VPN Router Wireless-G VPN Broadband Router Getting to Know the Wireless-G VPN Broadband Router Back PanelFront Panel DMZConnecting the Wireless-G Broadband Router OverviewWired Connection to a PC Wireless Connection to a PCWireless-G VPN Broadband Router Configuring the PCs Configuring Windows 98 and Millennium PCsConfiguring Windows 2000 PCs PropertiesConfiguring Windows XP PCs Setup Configuring the RouterWireless Security Access RestrictionsAdministration Applications & GamingBasic Setup Tab How to Access the Web-based UtilitySetup Tab Internet SetupStatic Internet Connection Type Optional Settings Required by some ISPs Pptp Internet Connection TypeNetwork Setup Ddns Tab DynDNS.orgMAC Clone MAC Address Clone Tab See FigureAdvanced Routing Tab Advanced RoutingStatic Routing 10 Routing TableBasic Wireless Settings See Figure Wireless TabWireless Network Wireless Security WEP See FigureWireless Network Access See Figure 13 Wireless Network AccessAdvanced Wireless Settings See Figure 15 Advanced Wireless SettingsSecurity Tab FirewallVPN 18 Manual Key Management 19 Advanced VPN Tunnel Setup WEP Access Restrictions Tab Access Restriction23 Internet Filter Summary Applications and Gaming Tab Port Range ForwardingPort Triggering 27 Port TriggeringUPnP Forwarding 28 UPnP ForwardingDMZ Router Password Administration TabManagement Email Alert LogUPnP Syslog NotificationAlert Log DiagnosticsNotification Queue Length General Log33 Factory Default Information StatusRouter WAN ConnectionsLocal Network 36 Local Network38 Wireless System PerformanceCommon Problems and Solutions Appendix a TroubleshootingNeed to set a static IP address on a PC Wireless-G VPN Broadband Router Wireless-G VPN Broadband Router Wireless-G VPN Broadband Router TCP UDP Can’t get the Internet game, server, or application to work Need to upgrade the firmware To start over, I need to set the Router to factory defaultFirmware upgrade failed, and/or the Power LED is flashing My DSL service’s PPPoE is always disconnecting Power LED flashes continuouslyIs IPSec Pass-Through supported by the Router? Frequently Asked QuestionsWhere is the Router installed on the network? Does the Router support IPX or AppleTalk?What is Network Address Translation and what is it used for? Does the Router support ICQ send file?How can I block corrupted FTP downloads? Is the Router cross-platform compatible? What is DMZ Hosting?What are the advanced features of the Router? How many ports can be simultaneously forwarded?What is ad-hoc mode? What is the Ieee 802.11g standard?What Ieee 802.11b features are supported? What is infrastructure mode?What is DSSS? What is FHSS? And what are their differences? What is ISM band?What is Spread Spectrum? What is WEP?How do I resolve issues with signal loss? How do I reset the Router?Have excellent signal strength, but I cannot see my network Brief Overview Appendix B Wireless SecurityWhat Are The Risks? Passive Attacks Jamming AttacksDictionary-Building or Table Attacks Maximizing Wireless SecurityActive Attacks Man-in-the-Middle Attacks5SSID 8WEP Wireless-G VPN Broadband Router 4GHz/802.11b and 802.11g WEP Encryption Figure B-2 WEPEnvironment WRV54GBuild Filter Lists How to Establish a Secure IPSec TunnelCreate an IPSec Policy Filter List 1 win-routerFilter List 2 router-win Figure C-4 IP Filter ListFigure C-7 IP Filter List Configure Individual Tunnel Rules Tunnel 1 win-routerFigure C-13 Authentication Methods Figure C-16 Tunnel Setting Tab Tunnel 2 router-winFigure C-19 IP Filter List Tab Figure C-22 Preshared Key Assign New IPSec Policy Figure C-25 Connection TypeCreate a Tunnel Through the Web-Based Utility Figure C-28 VPN TabFigure D-1 IP Configuration Screen Windows 98 or Me InstructionsWindows 2000 or XP Instructions Figure D-3 MAC Address/Physical AddressAppendix E Snmp Functions Figure F-1 Upgrade Firmware Appendix F Upgrading FirmwareShared Resources Appendix G Windows HelpNetwork Neighborhood/My Network Places Appendix H Glossary Wireless-G VPN Broadband Router Wireless-G VPN Broadband Router Wireless-G VPN Broadband Router Wireless-G VPN Broadband Router Wireless-G VPN Broadband Router Transmit Power 19dBm LEDs Appendix I SpecificationsUp to 54Mbps wireless, up to 100 Mbps LAN Appendix J Regulatory Information FCC StatementFCC Part 68 Statement Safety Notices Appendix K Warranty Information Limited WarrantyAppendix L Contact Information
Top Page Image Contents