Cabletron Systems SM-CSI1076, 1088, 1082 manual Ethernet Based Configuration, Error Source

Page 57

C o n f i g u r a t i o n V i e w s

Error Alarms

Allows you to enable or disable detection of Error Alarms. Possible menu selections are: Enable and Disable.

Error Threshold

Displays the threshold value for the percentage of errors per good packet that may occur within the Timebase before generating an error alarm. This value is user-configurable from 1 to 100.

Error Source

This area of the Repeater Configuration view provides a series of buttons that let you select the types of errors to include in the error sum. The selectable error types are as described below.

CRC

Packets with bad Cyclical Redundancy Checks.

Runts

A packet that is one byte less than the standard Ethernet frame of 64 bytes (not including preamble).

OOW_Colls

Collisions out of the standard window due to a network problem.

Alignment

Misaligned packets detected.

E t h e r n e t B a s e d C o n f i g u r a t i o n

No_Resource

The number of times the module ran out of resources (i.e., lack of buffer space) and could not accept packets.

Giants

Packets received that exceed 1518 bytes (not including preamble).

Ethernet Based Configuration

Access: From the Chassis Icon, select Ethernet Based

Configuration.

This view provides port configuration information for GPIM models. This view also shares fields with the Fast Ethernet Configuration View (page 54) and the shared fields are covered there. The fields below detail the device specific information found with this view.

Auto Negotiate Mode

Indicates whether Auto-Negotiation is enabled for a specific port. If Auto-Negotiation is disabled the port will revert to the speed, duplex, and flow control settings specified by their associated leaves in the Flow Control groups.

Remote Auto Signal

Indicates whether the remote end of the link is operating in Auto-Negotiation signaling or not.

S p e c t r u m E n t e r p r i s e M a n a g e r

Page 58

S m a r t S w i t c h 6 0 0 0

Image 57
Contents Device Management SmartSwitchVirus Disclaimer Contents Model Information View Index Introduction Purpose and ScopeRequired Reading Supported Devices Networking CharacteristicsManagement Modes Distributed Mode6C105 Chassis SmartSwitch 6000 ChassisSpectrum Products SmartSwitch 6000 Modules6E Series Connectivities Product Module Group6H Series Connectivities Spectrum ModelDevice Icons Views Summary Fast Ethernet Operation Check TasksFirmware Upgrade Repeater Port Speed Set Device Performance View Performance ViewsDevice Performance View Bridging Performance ViewInterface Performance View Repeater Port Performance View Chassis Device View Device ViewsChassis Module Icon Chassis Module IconModule Icon Subviews Module Identification LabelsSlot Number Model TypeApplication Label Bridging Application Icon SubviewsOption Opens Interface Type Label Interface LabelsInterface Status Label Bridging Application Interface StatusRepeater Index Repeater LabelsRepeater Status Repeater Label Icon Subviews MenuDelta TotalAccum ClearRepeater Port Label Icon Subviews Repeater Port LabelsRepeater Port Number Repeater Port StatusChassis Information Power RedundancyPS #1 Status PS #2 StatusInterface Device View Interface Device ViewInterface Icon Administrative Status LabelInterface Number Label Interface Icon SubviewsMAC Address Label Backplane Device ViewNetwork Information Label Gauge LabelBackplane Device View Backplane Module Icon Backplane Module Icon SubviewsBackplane Module Icon Subviews Option OpenBackplane Connection Status Descriptions Backplane Connections LabelsPhysical Device View Physical Device ViewDevice Topology View Device Topology ViewApplication View Applications ViewApplication Icon Application IconsSupported Applications Fast Ethernet Application ViewFast Ethernet Port Table Common ApplicationsATM Client Application Operational ModeInterface Port GroupATM Client Application VCL Table Encaps Type Receive SizeVCL CC Cross Connect Id Row StatusVirtual Channel Link View VPI Virtual Path IdentifierVCI Virtual Channel Identifier Cross Connect Id Xmit Descr IndexRcv Descr Index CsRipEnetRpt Repeater Application Download ApplicationCsRipEnetRpt Application Icon Subviews Menu OpenDevice Configuration View Configuration ViewsInterface Configuration Table Port Configuration CSIIfPort View FddiMAC Device Configuration ViewStation Configuration MAC Count MAC AddressNon Master Ports Master PortsSMT MAC Configuration States SMT Information ATM Client Configuration ViewAddress Type Admin AddressNeighbor Address Neighbor If NameOperational Mode Fast Ethernet Configuration ViewAdvertised Ability Operational Mode ValuesReceived Technology Advertised Ability ValuesRepeater Management Repeater Configuration ViewAlarm Configuration Trap ConfigurationError Source Ethernet Based ConfigurationPort Type Flow ControlLink Status Advertised AbilitiesModel Information View Model Information ViewModeling IntroductionAutoDiscovery vs. Manual Modeling Container View Manual Modeling OverviewPreparation for Modeling Modeling Using the Chassis IPSelect Model Type Dialog Box Select Edit New Model New Model By IP OptionPositioning the Chassis Device Icon Numerics IndexMAC Ttrt Wrap