Cabletron Systems SSIM-H2-02 manual Serial Download, From the main menu, select Download→ Upload

Page 18

9

The console will display the download activity while the software is transferred over the network by counting received blocks. When the software has been transferred, you will see the following messages:

Network download complete. Now transferring to TS

Module(s), please wait...

Download of TS firmware complete - TS module(s) being

reinitialized...

➽Warning: If you use Telnet as a manager console, download activity will not be displayed.

The software image is then programmed into the FLASH memory on the module. The software image remains in memory until it is replaced. When the software installation is complete, the module is started for normal operation, and the following message is displayed:

Press <RETURN> to continue...

➽Note: Remember that new module software is active immediately after it is downloaded, but to activate the module’s software you must restart the switch.

Serial Download

1.From the main menu, select Download→ Upload.

2.Select Serial Link Download.

3.Select TS Firmware Download.

4.Using your terminal software, transfer the software image to the SSIM-H2-02 with the X-Modem protocol. The transfer may take several minutes, depending on your terminal emulator baud.

The software image is then programmed into the FLASH memory of the module, and will remain there until it is replaced. When the software installation is complete, the module is started for normal operation and the following message is displayed:

Press <RETURN> to continue...

SSIM-H2-02 Fast Ethernet - Translational Switch SmartStack Interface Module Installation and User Guide

Installation

Image 18

Contents Page Order Number 9032962-01 OC-7063 v .1 FCC Notice Vcci NoticeIndustry Canada Notice Declaration of Conformity Addendum IiiApplication of Council Directives 89/336/EEC 73/23/EEC Page Table of Contents Statistics List of Figures ViiList of Tables ViiiSSIM-H2-02 Switch SmartStack Interface Module IntroductionFeature Description Snmp is supported via the host processor This makes it possible to configure the devicePart of the LAN switch Processor on the SmartStack STS16-20RMMIB Support FEUplink MIBInstallation Package ContentsInstallation Procedure Hardware Installation Removing the Expansion Slot CoverSoftware Installation Tftp DownloadSerial Download From the main menu, select Download→ UploadCabling LEDsPower-On Self Test Configuration Default ConfigurationConfiguration Introduction Ports, Port Groups and VLANsTS Virtual Ports and Vlan Tagging Virtual Port RestrictionRing Number Restriction Source Routed Switching SRS Operation Mode Source Routed Transparent Bridging SRT ModeBridging Modes Source Routed Bridging SRB Mode Ethernet CRF in SRB Bridging ModeRedundant Connections to Fast Ethernet Network Network ScenariosPreventing Frame Duplication Preventing Frame Looping Frame LoopingSpanning Tree Configuration Broken Ethernet CloudRedundant Connections to Fast Ethernet Network Page Technical Background STP Cost Modification General Guidelines Main Switch Menu Navigating Within the MenusConfiguration Overview BRF Configuration Vlan ConfigurationPort Configuration TS Ports Local Vlan Port ConfigurationDisplay only. Shows the current status of the port Virtual Port ConfigurationStatus Address Demand Aging LevelYou can use only one value as MTU DefaultDisplay only. Shows the current status of the virtual port 1558 001Address Aging Time Vlan Tagging ModeFC Modification RIF Not Learn IntervalFrame Conversion Configuration IP Conversion StatusIP Conversion Parameters Change Sets the format of IP frames on Ethernet Default SRIP Ethernet Format Snap Frame in the Ieee 802.3 format with SnapExplorer Frames Type Enable IP FragmentationNovell Conversion Status TR MAC Address for IP MulticastsNovell Token Ring Format Novell Conversion Parameters ChangeNovell Frames Conversion Novell Ethernet FormatNetBios Frames Conversion NetBios Conversion StatusNetBios Conversion Parameters Change IPX Address TranslationNetBios Token Ring Format NetBios Ethernet FormatSNA Conversion Status SNA Conversion Parameters ChangeSNA Ethernet Format Sets the format of SNA frames on EthernetOther Frames w/SNAP Frames Conversion Other Frames w/SNAP Conversion StatusOther Frames w/SNAP Conversion Parameters Change Other Frames w/SNAP Token Ring FormatOther Frames w/o Snap Conversion Status Other Frames w/SNAP Ethernet FormatOther Frames w/o Snap Token Ring Format Other Frames w/o Snap Conversion Parameters ChangeOther Frames w/o Snap Frames Conversion Other Frames w/o Snap Ethernet FormatDual Home FEP Addresses Configuration Page Statistics Statistics Menu Port Status Port Statistics General StatisticsDiscarded Frames Locally Filtered Table Filtered by Address FilterTable Filtered by Dsap Filter Table Blocked Virtual PortTraffic Counters Error Counters Virtual Port State Virtual Port StatisticsDiscarded Frames Statistics Frames ForwardedOther w/SNAP NetBiosInbound Translation errors Other w/o SnapOutbound Translation Errors Outbound No TranslationFragmentation Error Generic w/o SnapGetting in Touch with Technical Support Your email addressPage Appendix A. Abbreviations Source Route Switching Service Access PointSub-Network Access Protocol Translational SwitchIndex Index-1Local Vlan port configuration Index-2710001816