Cabletron Systems SSIM-H2-02 manual Cabling, LEDs

Page 19

10

Cabling

The module uses standard or crossed-over UTP-5 copper cables. The maximum cable length is 100 m (328 feet).

1.Insert the modular RJ-45 jack from either end of a standard or crossed-over UTP-5 cable into one of the connectors on the SSIM-H2-02 front panel.

2.Connect the other end of the cable to:

another TS port (using the crossed-over UTP-5 cable)

100/10 MB Ethernet adapter (using the crossed-over UTP-5 cable)

100/10 MB Ethernet switch or hub port (using the standard UTP-5 cable)

LEDs

There are eight LEDs on the front panel of the SSIM-H2-02. During normal operation, the two LEDs on the left side of the front panel indicate the module status:

LED

Position

State

 

Meaning

 

 

 

 

 

 

 

 

 

 

DIAG (green)

Top

On

 

Diagnostics are in process.

 

 

 

 

 

 

 

Off

 

No diagnostics are in process.

 

 

 

 

 

ERR (yellow)

Bottom

On

 

A module failure has occurred.

 

 

 

 

 

 

 

Off

 

The module is working

 

 

 

 

correctly.

 

 

 

 

 

 

 

Table 2. LEDs at the Left on the Front Panel

 

The three LEDs on the right of every port indicate the port status:

LED

Position

State

Meaning

 

 

 

 

 

 

 

 

ACTIVITY

Top

Flashing

The port is receiving or

(green)

 

 

transmitting frames.

 

 

 

 

 

 

Off

Currently no traffic on the port.

 

 

 

 

 

 

 

 

Table 3. LEDs at the Right of Every Port

SSIM-H2-02 Fast Ethernet - Translational Switch SmartStack Interface Module Installation and User Guide

Installation

Image 19
Contents Page Order Number 9032962-01 OC-7063 v .1 Vcci Notice FCC NoticeIndustry Canada Notice Iii Declaration of Conformity AddendumApplication of Council Directives 89/336/EEC 73/23/EEC Page Table of Contents Statistics Vii List of FiguresViii List of TablesIntroduction SSIM-H2-02 Switch SmartStack Interface ModuleFeature Description Processor on the SmartStack STS16-20RM This makes it possible to configure the devicePart of the LAN switch Snmp is supported via the host processorFEUplink MIB MIB SupportPackage Contents InstallationInstallation Procedure Removing the Expansion Slot Cover Hardware InstallationTftp Download Software InstallationFrom the main menu, select Download→ Upload Serial DownloadLEDs CablingPower-On Self Test Default Configuration ConfigurationConfiguration Ports, Port Groups and VLANs IntroductionVirtual Port Restriction TS Virtual Ports and Vlan TaggingRing Number Restriction Source Routed Transparent Bridging SRT Mode Source Routed Switching SRS Operation ModeBridging Modes Ethernet CRF in SRB Bridging Mode Source Routed Bridging SRB ModeNetwork Scenarios Redundant Connections to Fast Ethernet NetworkPreventing Frame Duplication Frame Looping Preventing Frame LoopingBroken Ethernet Cloud Spanning Tree ConfigurationRedundant Connections to Fast Ethernet Network Page Technical Background STP Cost Modification General Guidelines Navigating Within the Menus Main Switch MenuConfiguration Overview Local Vlan Port Configuration Vlan ConfigurationPort Configuration TS Ports BRF ConfigurationAddress Demand Aging Level Virtual Port ConfigurationStatus Display only. Shows the current status of the port1558 001 DefaultDisplay only. Shows the current status of the virtual port You can use only one value as MTURIF Not Learn Interval Vlan Tagging ModeFC Modification Address Aging TimeIP Conversion Status Frame Conversion ConfigurationIP Conversion Parameters Change Snap Frame in the Ieee 802.3 format with Snap Default SRIP Ethernet Format Sets the format of IP frames on EthernetTR MAC Address for IP Multicasts Enable IP FragmentationNovell Conversion Status Explorer Frames TypeNovell Ethernet Format Novell Conversion Parameters ChangeNovell Frames Conversion Novell Token Ring FormatIPX Address Translation NetBios Conversion StatusNetBios Conversion Parameters Change NetBios Frames ConversionNetBios Ethernet Format NetBios Token Ring FormatSNA Conversion Parameters Change SNA Conversion StatusSets the format of SNA frames on Ethernet SNA Ethernet FormatOther Frames w/SNAP Token Ring Format Other Frames w/SNAP Conversion StatusOther Frames w/SNAP Conversion Parameters Change Other Frames w/SNAP Frames ConversionOther Frames w/SNAP Ethernet Format Other Frames w/o Snap Conversion StatusOther Frames w/o Snap Ethernet Format Other Frames w/o Snap Conversion Parameters ChangeOther Frames w/o Snap Frames Conversion Other Frames w/o Snap Token Ring FormatDual Home FEP Addresses Configuration Page Statistics Statistics Menu Port Status General Statistics Port StatisticsDiscarded Frames Table Blocked Virtual Port Table Filtered by Address FilterTable Filtered by Dsap Filter Locally FilteredTraffic Counters Error Counters Frames Forwarded Virtual Port StatisticsDiscarded Frames Statistics Virtual Port StateOther w/o Snap NetBiosInbound Translation errors Other w/SNAPOutbound No Translation Outbound Translation ErrorsGeneric w/o Snap Fragmentation ErrorYour email address Getting in Touch with Technical SupportPage Appendix A. Abbreviations Translational Switch Service Access PointSub-Network Access Protocol Source Route SwitchingIndex-1 IndexIndex-2 Local Vlan port configuration710001816