Cabletron Systems 2200 manual No link

Page 43

 

 

 

Using LANVIEW

 

 

 

 

 

Table 4-1 LANVIEW LEDs (Continued)

 

 

 

 

LED

Color

State

Recommended Action

 

 

 

 

CPU

Off

Power off.

Power up device.

 

 

 

 

 

Red

Blinking. Hardware

Contact Cabletron Systems for technical

 

 

failure has occurred.

support.

 

 

 

 

 

 

Solid. Resetting, normal

If the LED remains red for several minutes,

 

 

power up reset.

contact Cabletron Systems for technical

 

 

 

support.

 

 

 

 

 

Amber

Blinking. Crippled.

Contact Cabletron Systems for technical

 

 

 

support.

 

 

 

 

 

 

Solid. Testing.

If the LED remains amber for several

 

 

 

minutes, contact Cabletron Systems for

 

 

 

technical support.

 

 

 

 

 

Green

Solid. Functional.

None.

 

 

 

 

 

Amber

Booting. Blinks amber

None.

 

and

and green while booting.

 

 

Green

 

 

 

 

 

 

RX

Off

No link.

None.

(Receive)

 

No activity or port in

 

 

 

standby. Port enabled or

 

 

 

disabled.

 

 

 

 

 

 

Green

Solid. Link, port enabled,

None.

 

 

no activity.

 

 

 

 

 

 

 

Blinking. Link, port

None.

 

 

disabled.

 

 

 

 

 

 

Amber

Flashing. Link, port

None.

 

 

enabled, activity.

 

 

 

 

 

 

Red

Solid. Diagnostic failure.

Contact Cabletron Systems for assistance.

 

 

 

 

Troubleshooting 4-3

Image 43
Contents 2E253-49R SmartSwitch Installation User’s Guide Page Page FCC Notice Cabletron SYSTEMS, INC Program License Agreement Page Page Page Cabletron Systems Limited Program License Agreement Viii Declaration of Conformity Page Contents Troubleshooting Figures Tables About This Guide Using this GuideStructure of this Guide Xvi Related DocumentsDocument Conventions Document ConventionsPage Overview IntroductionConnectivity Full Duplex Switched EthernetRuntime IP Address Discovery Standard/Full Duplex Auto-NegotiationSmartTrunk Broadcast Suppression Remote Monitoring RmonPort/VLAN Redirect Functions Flow Control Traffic Rate LimitingManagement Garp Switch OperationSwitching Options 12 802.1 Port PriorityYear 2000 Compliance Lanview Diagnostic LEDsOptional HSIMs and VHSIMs Standards CompatibilityFTP Getting Help10BASE-T Network Network RequirementsPage Installation Unpacking the Device Installing OptionsTabletop or Shelf Installation Installing the DeviceGuidelines for the Rackmount Installation Rackmount InstallationAttaching the Strain-Relief Bracket Rack Mounting the 2E253-49R Installing the Device in a Rack Connecting PowerRedundant Primary AC outlets are On separate circuits Connecting to the NetworkConnection Using the RJ21 Angle Adapter Completing the Installation Using Lanview TroubleshootingPWR No link Is enabled and there is a OFF Troubleshooting Checklist2E253, 2H252, 2H253, and 2H258 Local Reset Button Using the Reset ButtonPage Specifications Device SpecificationsPhysical Properties Environmental Requirements Electrical SpecificationsINPUT/OUTPUT Ports Regulatory Compliance COM Port Pinout AssignmentsPage Required Tools Optional Installations Mode Switch Bank SettingsRemoving the Chassis Cover To remove the chassis cover, proceed as follows Screws Chassis Cover Front Panel Switch 6 Forced BootP Setting the Mode SwitchesSimm Upgrade Locating SIMMs Figure B-3shows the location of the Dram Simm connectorSimm Installing the Dram SimmFigure B-5 Hsim and Vhsim Connector Locations Installing Optional Hsim or Vhsim Interface ModulesPage Numerics IndexIndex-2